Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

[bug report & fix] app_uart_fifo is sending APP_UART_TX_EMPTY event before the last byte is sent 0

Hi Team, We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...

1778 views

0 replies

Started over 7 years ago
by Patrice Rudaz
Not Answered
Pairing procedure failed by bonding 0

Hello everybody, for my project, i will bond the peripherial with the central. I test my device with the MCP and can connect without problems. When i press the Bond Button...
- bond
- sdk11
- s132
- nrf52832
1193 views

0 replies

Started over 7 years ago
by 1_andi
Not Answered
nRF52 max. input frequency on GPIO 0

Hi all, I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
- 132 nrf52832 gpio
1970 views

0 replies

Started over 7 years ago
by Pascal Künzi
Not Answered
NRF52840DK w/S140 hardfault 0

Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio. App flash base is set to 0x00021000 and app RAM base is set to 0x20003000 Looking at the CPU...
- nrf52840dk nrf52 nrfgo
559 views

0 replies

Started over 7 years ago
by Ove-Anders Gaarder Aune
Not Answered
Bluetooth name length limit less in SDK12.0.0 than in SDK8.0.0? 0

In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
- nrf5
- sdk12
- sdk8
- bluetooth name length
486 views

0 replies

Started over 7 years ago
by Jarmo

Recent in Nordic blog

New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019