Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

[Solved] SPI: Not getting SCK signal 0

Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong. Hi guys, at the...

1366 views

0 replies

Started over 7 years ago
by uC_newbie
Not Answered

Looking for a developer in Denmark 0

Hi Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...

482 views

0 replies

Started over 7 years ago
by Martin
Not Answered

One RX and Three TX system with NRF24L01+ 0

This system does not work if I enable the third Pipe (Pipe2) . The system is working without any problem as one RX and two TX (Pipe0 and Pipe1). The problem on enabling...

513 views

0 replies

Started over 7 years ago
by Erol
Not Answered
sd_flash_write inside BLE event 0

Hello, i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method. What i would like to do is to write to flash from...
- sd_flash_write
- event
- ble
- flash
- nrf52832
976 views

0 replies

Started over 7 years ago
by schef
Not Answered
sd_flash_write in BLE event 0

Hello, i have read all posts about writing to FLASH when using BLE. But could not find the desirable method. What i would like to do is to write to flash from characteristic...
- sd_flash_write
- event
- nrf52
- ble
- flash
976 views

0 replies

Started over 7 years ago
by schef

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020