Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

How to know the master is iOS or android? 0

How to know the master is iOS or Android when nRF51/52 is advertising or connected?

464 views

0 replies

Started over 8 years ago
by efengzu
Not Answered
Nrf5 IoT sdk Warning issue 0

hello i am using the Nrf52dk with Visualgdb. i try to run the example project (tcp/IP -> client). i am using the Nrf5 IoT sdk v0.9 Project complied successfully but i...
- nrf52
- iot
748 views

0 replies

Started over 8 years ago
by All4here
Not Answered

OpenOCD with nRF52 and Olimex debugger 0

I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...

2226 views

0 replies

Started over 8 years ago
by Tosa
Not Answered

nRF24LE1 (multiple) to nRF24L01 (1) sample RF projects? 0

Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...

1272 views

0 replies

Started over 8 years ago
by mr_creosote
Not Answered

task time of radio from DISABLE to RX 0

HI: i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow: while (1) { Rf_StartRx(ReciverSC.RfBufPointer...

514 views

0 replies

Started over 8 years ago
by baicai

Recent in Nordic blog

Reprogram the nRF51822 Beacon Kit to work with iOS 8

rvaessen

When I decided to attempt the reprogramming of my nRF51822 Beacon Kit I read several posts related to the task. The information I needed was there but I found it to be a bit scattered. It was difficult…
- 30 Aug 2015
Nordic's infocenter

Oisin

The Infocenter – our new documentation portal - has now been up and running since June and contains all of our technical documentation. We saw the need for this because we wanted to make our complete…
- 24 Aug 2015
nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019