Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

OpenOCD with nRF52 and Olimex debugger 0

I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...

2204 views

0 replies

Started over 8 years ago
by Tosa
Not Answered

nRF24LE1 (multiple) to nRF24L01 (1) sample RF projects? 0

Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...

1258 views

0 replies

Started over 8 years ago
by mr_creosote
Not Answered

task time of radio from DISABLE to RX 0

HI: i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow: while (1) { Rf_StartRx(ReciverSC.RfBufPointer...

504 views

0 replies

Started over 8 years ago
by baicai
Not Answered

nrf51822 and tmp102 0

Hi to everyone, i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822. I want to read the values of the sensor over a beacon app. ...

534 views

0 replies

Started over 8 years ago
by Roberto
Not Answered

After DFU, the device can't reset 0

Hi,I'm glad you can see my post. Now, I am in a program to read and write FLASH such as the screenshot in the attachment. Then I update with DFU service for the equipment...

717 views

0 replies

Started over 8 years ago
by ymYin

Recent in Nordic blog

On nRF Connect for iOS and its Unnecessary BitField Collection in Swift

Dinesh Harjani

For the longest time we’ve had this idea, of turning one of our most-used Swift Collection Types into a simple one-instruction comparison call, down at the assembly level, to check whether an element belongs…
- 23 Jul 2020
Measuring PSM Sleep Current on the nRF9160-DK

notsane0

Overview In this blog, you will measure the PSM floor current for the rev. 2 version of the nRF9160 SiP. Requirements Hardware You will need: an nRF9160-DK (the one used here was v1.0.0). Be sure that…
- 7 May 2020
Developing for the nRF52820 with nRF5 SDK v16.0.0

bjorn-spockeli

Please note that this blogpost is now deprecated as the nRF52820 is fully supported in nRF5 SDK v17.0.0. We recommend using SDK v17.0.0 for nRF52820 fimware development. Introduction The nRF52820 IC is…
- 19 Mar 2020

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019