Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nrf51822 and tmp102 0

Hi to everyone, i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822. I want to read the values of the sensor over a beacon app. ...

578 views

0 replies

Started over 8 years ago
by Roberto
Not Answered

After DFU, the device can't reset 0

Hi,I'm glad you can see my post. Now, I am in a program to read and write FLASH such as the screenshot in the attachment. Then I update with DFU service for the equipment...

753 views

0 replies

Started over 8 years ago
by ymYin
Not Answered
Master Control Panel - Change MTU size 0

Hi Is it possible to change the MTU size with the Master Control Panel? I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
- mtu
1499 views

0 replies

Started over 8 years ago
by cp52
Not Answered
can anybody share a battery_level_in_percent for AA battery? 0

Is there a function like battery_level_in_percent for AA battery? I know battery_level_in_percent is only for CR2032. Even though I compensate it to make it 3V from AA battery...
- battery level
- adc
1083 views

0 replies

Started over 8 years ago
by sosse
Not Answered
Code compilation issues with PIC / XC8 - expression generates no code 0

Hi, The following function: void acil_encode_cmd_setup(uint8_t *buffer, aci_cmd_params_setup_t *p_aci_cmd_params_setup, uint8_t setup_data_size) { *(buffer + OFFSET_ACI_CMD_T_LEN...
- pic xc8
4505 views

0 replies

Started over 8 years ago
by didier

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020