Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
fds FRESH_INSTALL, desired functionality. Attempt to build unsuccessful 0

I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
- fds keil stack flash
683 views

0 replies

Started over 8 years ago
by dav lion
Not Answered

device_manager_evt_handler return error 0x88 0

nrf51822 SDK v10 SD S110 v8 hello! My pj is about ANCS+nus+hid mouse sevices. If my borad had bonded with an iPhone,then download new hex from mdk ,and run. ...

589 views

0 replies

Started over 8 years ago
by qinhao
Not Answered

segger jlink cortex m4f floating point debugging 0

Hello. I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB. I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...

760 views

0 replies

Started over 8 years ago
by kobyfr
Not Answered
app_timer_appsh and debug with repeat timer, nRF51 0

When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug. To work...
716 views

0 replies

Started over 8 years ago
by Jon (jono)
Not Answered
Setting a hardware timer 0

I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
- nrf52 timer s132 gcc eclipse
2242 views

0 replies

Started over 8 years ago
by archangel689

Recent in Nordic blog

Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020