Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Configure P0.05/P0.07 as GPIO when using uart0 0

I've got a custom board using an nRF52832. I'm using the P0.06/P0.08 as the TX/RX pins for UART comms, but don't need the P0.05/P0.07 pins for CTS/RTS. Is there anyway I can...
37 views

0 replies

Started 2 days ago
by Mike Austin (LPI)
Not Answered
nRF Connect for Desktop Bluetooth Low Energy stops working with nRF52840 devkit 0

Hello, I'm using my nRF52840 devkit together with nRF Connect for Desktop Bluetooth Low Energy (v4.0.4) app for some testing. The app failed to recognize my devkit. It used...
33 views

0 replies

Started 2 days ago
by John
Not Answered
Setting up custom Secure Bootloader 0

Hello Nordic Team, I'm developing an project using VS Code with nRF Connect Extension for an nRF52832 board. The SDK version I use is 2.7.0 , build system is sysbuild . I...
56 views

0 replies

Started 2 days ago
by wounderkid_
Not Answered
nRF Connect for Desktop Bluetooth Low Energy fails 0

Hello, after a longer time, I wanted to use nRF Connect for Desktop again, to figure out what exactly my device under development is advertising. I upgraded to the latest...
32 views

0 replies

Started 2 days ago
by Torsten Robitzki
Not Answered
Adding clusters to Matter application Example 0

Hello Nordic team, I followed the official guide to add a custom sensor cluster to my Matter application. Everything built and flashed successfully, and the application...
- software
- beginner
- Evaluation
- thread
- nfc
- nRF5340
96 views

0 replies

Started 2 days ago
by BlockT

Recent in Nordic blog

One tool to rule them all: nRF Util becomes a unified command line utility

Ali Aljaani

nRF Util is Nordic's command line utility for Nordic products. You can easily use it to flash applications onto your Nordic device through a terminal. In the most recent major version update, v7.0.0…
- 5 Jan 2023
Reading Thingy:53 sensor data using Bluetooth LE

Tiago Monte

The Thingy:53 is a bleeding edge IoT prototyping platform featuring the flagship nRF5340 dual-core Wireless SoC. It also contains several sensors and a rechargeable Li-Po battery, making it an excellent…
- 9 Dec 2022
Printing to an I2C OLED display using nRF Connect SDK

helsing

If you are a human, as opposed to a microcontroller, you might want an easy and intuitive way to read out data from your application. Adding a small OLED display to your project is a simple solution for…
- 3 Nov 2022

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019