Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Supporting multiple network interfaces + devices on one MCU 0

Hello, I'm working with a custom board using an nRF5340 as its primary MCU and NCS 2.7.0. The application I'm developing requires internet connection and can ideally support...
44 views

0 replies

Started 1 day ago
by Amira R.
Not Answered
BLE antenna switching on/off while transmitting 0

Hello, We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
- Evaluation
- antenna
- nrf52832
- bluetooth le
- ant
- rf design
- hardware
57 views

0 replies

Started 2 days ago
by xinyangt
Not Answered
How to software-switch between ESB and BLE on a nrf5340 net-core? 0

Hi, I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
50 views

0 replies

Started 2 days ago
by nfbe
Not Answered
Emulating Xinput, what are the requirements? 0

Hello, I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
- development
- software
- nrf52840
- usb
49 views

0 replies

Started 2 days ago
by blitz0145
Not Answered
CMakePresets.json broke in new nRF Connect for VS Code version 0

Hi We are using the CMakePresets.json file for different variations of our firmware. Since the latest update (2025.4.106) the build configuration interface changed a bit...
41 views

0 replies

Started 2 days ago
by AlanIoT

Recent in Nordic blog

Log continuously for up to 500 days with the PPK2!

Robin M Saltnes

One of the things you asked us for after launching the new Power Profiler Kit II (PPK2) was extending the maximum logging time, some of you wanted hours or even days of continuous logging. We went to work…
- 19 Feb 2021
Allowing debugger access to nRF5340

Daniel Veilleux

After an nRF5340 executes a power-on, brown-out, watchdog timer, or pin reset it is not automatically accessible to debug probes. This is true even if the nRF5340's memory is completely blank --i.e. no…
- 15 Jan 2021
Connected Home over IP: Sneak peek of early development on nRF52840

Lukasz Duda

This blog post provides step-by-step instruction on running Door Lock example from the CHIP repository. It demonstrates how with help of the mobile phone, commission accessory to the network using Bluetooth…
- 28 Dec 2020

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020