Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

ble-sniffer_win_1.0.1_1111_Sniffer.exe exited unexpectedly 0

I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed. I am attaching the log.txt. log...

1789 views

0 replies

Started over 9 years ago
by Paul
Not Answered

From which function new node will get version detail for the first time in mesh 0

Hi all, I am using ble open mesh with pca10028 boards ble mesh is working fine. I am developing a application that has to blink led in mesh( without any delay between...

2205 views

0 replies

Started over 9 years ago
by Manjunath
Not Answered

low power uart mode leaves TX asserted while CTS is disabled 0

I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...

643 views

0 replies

Started over 9 years ago
by Jim Dattolo
Not Answered
BLE nRF OpenMesh - data rates in typical configurations 0

Hello, I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture. I'm considering using it in a network consisting...
1412 views

0 replies

Started over 9 years ago
by piorossi
Not Answered
Is it useful to simulate my PCB design using CST Studio?and How? 0

Hello Nordic Community, I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
2036 views

0 replies

Started over 9 years ago
by mahmoud.tolba

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019