Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
PCB antenna used in the nRF51 DK 0

I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
- antenna nrf51dk
742 views

0 replies

Started over 9 years ago
by BCNLANYC
Not Answered
How to see which part of the code/variable is using more Memory ? 0

Hi. I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
- nrf52 keil c memory
749 views

0 replies

Started over 9 years ago
by Muhammad Ahmad Shah
Not Answered
asynchronous pulse counting in low power mode 0

Hello, I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode. Pulses are asynchronous The rate of pulses can...
1077 views

0 replies

Started over 9 years ago
by fakufaku
Not Answered
nRF52 SAADC gain error a function of Vcc? 0

Hi I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52. Both the reference resistor and the PT-100 is sampled while the voltage...
- nrf52
- adc
- gain
- vcc
- nrf52382
- saadc
2249 views

0 replies

Started over 9 years ago
by Visti Andresen
Not Answered
Sample multiple inputs with fixed rate using ADC hal 0

Hi I have been searching the forums, but were not able to find an answer to my question. I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
- adc
- oftdevice
1269 views

0 replies

Started over 9 years ago
by Phillip

Recent in Nordic blog

Nordic Semiconductor nRF51822 Firmware for Background Data Recording

scytulip

#Nordic Semiconductor nRF51822 Firmware for Background Data Recording Updating on https://github.com/scytulip/nrf51-back-rec Design Objective This firmware is designed for low-cost long-time low-power…
- 23 Oct 2014
Nordic nRF51822 ARM Cortex-M0 Development using emIDE

Hugh

Nordic nRF51822 ARM Cortex-M0 Development using emIDE To avoid the hefty charges with commercial compilers I tried emIDE with some success; here are the settings I used for the EV Kit Official emIDE…
- 22 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014

Latest guides

Software: Using a custom Secure Partition Manager with your application

Heidi

One of the samples available in the nRF Connect SDK is the Secure Partition Manager, which is required to run applications in the nonsecure domain of the CPU. The sample uses the SPM library available in…
- 12 Feb 2020
Getting Started : nRF Connect SDK Bluetooth Low Energy tutorial part 1: Custom Service in Peripheral role

haakonsh

Scope The goal of this tutorial is to set-up your own custom Bluetooth Low Energy service on an nRF5340 acting in a peripheral role. We will set up a new Bluetooth LE project from scratch. The finished…
- 11 Feb 2020
Mesh Networks: Mass Provisioning of Nordic BLE Mesh Nodes

Mark Q

Purpose When creating a mesh network with many nodes, it can take a while to provision each node, especially using PyACI. An alternative is to use a static provisioner that provisions the nodes automatically…
- 8 Feb 2020
Software and Protocols: Enabling and testing TLS in mqtt_simple

Daniel Veilleux

The MQ Telemetry Transport (MQTT) protocol is hugely popular in IoT because it is lightweight and versatile. In this post we will enable Transport Layer Security (TLS) in the mqtt_simple sample from the…
- 4 Feb 2020
Getting Started: Introduction to Nordic nRF5 SDK and Softdevice

Mihua

What is the difference between SDK and Softdevice? How can we select SDK and Softdevice versions? Do the SoC, SDK, and Softdevice have version compatibility problems? How can we understand the SDK directory…
- 15 Jan 2020
Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020