Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Receiver sensitivity 0

We are using nRF51822 for our products. We want to know the min value of "Receiver sensitivity" when we use this chip for BLE. The Datasheet says "Receiver sensitivity...
- receiver sensitivity nrf51822
2181 views

0 replies

Started over 8 years ago
by makoto
Not Answered
How to send and recive data to mutiple peripheral devices 0

Dear The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral) shows how one central device can connect to multiple peripheral devices. ...
- multiple peripheral
632 views

0 replies

Started over 8 years ago
by sjkim
Not Answered
Eddystone URL parser is broken in MCP 0

In the MCP app, if I have the following service data for an Eddystone beacon: 0x10, // Eddystone-URL type 0x00, // TX power in dBm. This is a signed integer so 0xEE ...
764 views

0 replies

Started over 8 years ago
by Tim
Not Answered
Cannot connect to BLE devices requiring random LE address type with Android nRF app 0

I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect. I know Fitbit wristbandes...
2898 views

0 replies

Started over 8 years ago
by Axelle
Not Answered

Communication between Gazell and non-gazell devices 0

Hi, The situation: I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...

742 views

0 replies

Started over 8 years ago
by nordicdev

Recent in Nordic blog

Reprogram the nRF51822 Beacon Kit to work with iOS 8

rvaessen

When I decided to attempt the reprogramming of my nRF51822 Beacon Kit I read several posts related to the task. The information I needed was there but I found it to be a bit scattered. It was difficult…
- 30 Aug 2015
Nordic's infocenter

Oisin

The Infocenter – our new documentation portal - has now been up and running since June and contains all of our technical documentation. We saw the need for this because we wanted to make our complete…
- 24 Aug 2015
nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019