Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
PCB antenna used in the nRF51 DK 0

I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
- antenna nrf51dk
721 views

0 replies

Started over 8 years ago
by BCNLANYC
Not Answered
How to see which part of the code/variable is using more Memory ? 0

Hi. I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
- nrf52 keil c memory
685 views

0 replies

Started over 8 years ago
by Muhammad Ahmad Shah
Not Answered
asynchronous pulse counting in low power mode 0

Hello, I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode. Pulses are asynchronous The rate of pulses can...
1043 views

0 replies

Started over 8 years ago
by fakufaku
Not Answered
nRF52 SAADC gain error a function of Vcc? 0

Hi I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52. Both the reference resistor and the PT-100 is sampled while the voltage...
- nrf52
- adc
- gain
- vcc
- nrf52382
- saadc
2202 views

0 replies

Started over 8 years ago
by Visti Andresen
Not Answered
Sample multiple inputs with fixed rate using ADC hal 0

Hi I have been searching the forums, but were not able to find an answer to my question. I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
- adc
- oftdevice
1240 views

0 replies

Started over 8 years ago
by Phillip

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019