Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

From which function new node will get version detail for the first time in mesh 0

Hi all, I am using ble open mesh with pca10028 boards ble mesh is working fine. I am developing a application that has to blink led in mesh( without any delay between...

2178 views

0 replies

Started over 8 years ago
by Manjunath
Not Answered

low power uart mode leaves TX asserted while CTS is disabled 0

I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...

616 views

0 replies

Started over 8 years ago
by Jim Dattolo
Not Answered
BLE nRF OpenMesh - data rates in typical configurations 0

Hello, I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture. I'm considering using it in a network consisting...
1377 views

0 replies

Started over 8 years ago
by piorossi
Not Answered
Is it useful to simulate my PCB design using CST Studio?and How? 0

Hello Nordic Community, I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
1953 views

0 replies

Started over 8 years ago
by mahmoud.tolba
Not Answered
registering to listen ble_ancs_c events 0

Hi. I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
- nrf52 s132 ble ancs sdk v11
791 views

0 replies

Started over 8 years ago
by Matts

Recent in Nordic blog

Current vs Voltage for nrf51 CPU

FormerMember

Since I couldn't find the information of how the supply current would change with different supply voltage for nrf51 chip, this is the result of a little test that I made to get this info. Setup: nrf51…
- 9 Sep 2015
Using Eclipse's Managed Make with the nRF51 DK

i_am_trying

I have been using Eclipse to programming+build+flash+debugging my nRF51 DK apps. This requires carrying a Makefile forward, modifying as stuff changes...handling flash programming in less integrated way…
- 6 Sep 2015
Programming Inexpensive nRf51822 modules with Nordic nRF51-DK

Mahesh Venkitachalam

I've updated my article on external SWD programming using the nRF51-DK. I have also designed an adapter board for these modules. http://electronut.in/nrf51-dk-external-programming/#E3BO
- 6 Sep 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019