Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
BLE nRF OpenMesh - data rates in typical configurations 0

Hello, I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture. I'm considering using it in a network consisting...
1377 views

0 replies

Started over 8 years ago
by piorossi
Not Answered
Is it useful to simulate my PCB design using CST Studio?and How? 0

Hello Nordic Community, I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
1953 views

0 replies

Started over 8 years ago
by mahmoud.tolba
Not Answered
registering to listen ble_ancs_c events 0

Hi. I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
- nrf52 s132 ble ancs sdk v11
791 views

0 replies

Started over 8 years ago
by Matts
Not Answered
PCB antenna used in the nRF51 DK 0

I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
- antenna nrf51dk
721 views

0 replies

Started over 8 years ago
by BCNLANYC
Not Answered
How to see which part of the code/variable is using more Memory ? 0

Hi. I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
- nrf52 keil c memory
685 views

0 replies

Started over 8 years ago
by Muhammad Ahmad Shah

Recent in Nordic blog

Introducing TechDocs: Nordic's single source for all technical documentation

Tiago Monte

As engineers and developers creating IoT products, you will rely on various resources to bring your ideas to life. Oftentimes, one of the most indispensable resources gets overlooked, and it's one you…
- 5 Oct 2023
Extend your battery life with nRF Cloud's CoAP interface

Tuomas P

Low power is one of the cornerstones of Nordic’s cellular IoT solution. The nRF91 Series is built from the ground up with ultra-low power consumption in mind, and the nRF Connect SDK provides applications…
- 28 Sep 2023
Analyzing power consumption in Thread Sleepy End Devices

MBaczmanski

The Thread protocol is a reliable, secure, and scalable solution for low-power IoT devices. One of the important aspects of its implementation is drawing as little power as possible. This ensures a long…
- 24 Aug 2023

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019