Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
asynchronous pulse counting in low power mode 0

Hello, I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode. Pulses are asynchronous The rate of pulses can...
1043 views

0 replies

Started over 8 years ago
by fakufaku
Not Answered
nRF52 SAADC gain error a function of Vcc? 0

Hi I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52. Both the reference resistor and the PT-100 is sampled while the voltage...
- nrf52
- adc
- gain
- vcc
- nrf52382
- saadc
2202 views

0 replies

Started over 8 years ago
by Visti Andresen
Not Answered
Sample multiple inputs with fixed rate using ADC hal 0

Hi I have been searching the forums, but were not able to find an answer to my question. I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
- adc
- oftdevice
1240 views

0 replies

Started over 8 years ago
by Phillip
Not Answered

NRF24L01 sends 0

Hi I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...

538 views

0 replies

Started over 8 years ago
by Mani
Not Answered

What values can the nRF905 status register have? 0

Hi I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...

629 views

0 replies

Started over 8 years ago
by Pieter Roos

Recent in Nordic blog

Reprogram the nRF51822 Beacon Kit to work with iOS 8

rvaessen

When I decided to attempt the reprogramming of my nRF51822 Beacon Kit I read several posts related to the task. The information I needed was there but I found it to be a bit scattered. It was difficult…
- 30 Aug 2015
Nordic's infocenter

Oisin

The Infocenter – our new documentation portal - has now been up and running since June and contains all of our technical documentation. We saw the need for this because we wanted to make our complete…
- 24 Aug 2015
nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020