Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
about nrf24le1debug problem
View Voters Login to vote on this thread 0 Login to vote on this thread
0

hi: now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
- 24le1 debug
609 views

0 replies

Started over 9 years ago
by jerly
Not Answered

Communication timeout. Emulator did not re-enumerate
View Voters Login to vote on this thread 0 Login to vote on this thread
0

This is what I got after upgrading my nRF51 dongle firmware. It always times out. I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...

2039 views

0 replies

Started over 9 years ago
by Paul
Not Answered
APP which support to conect 8 or more BLE peripherals
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hi all, Good day. Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time. Thanks & Regards Jenson
- bluetooth low energy
610 views

0 replies

Started over 9 years ago
by Jenson
Not Answered

nRF51xxx debugging with BDI debugger
View Voters Login to vote on this thread 0 Login to vote on this thread
0

I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...

706 views

0 replies

Started over 9 years ago
by robertos
Not Answered

Scaner Design uisng nRF24L01
View Voters Login to vote on this thread 0 Login to vote on this thread
0

hi, I want to scan ism band to detect active nRF24L01 transmitters. How much time receiver will take to scan the whole band.?

776 views

0 replies

Started over 9 years ago
by adnan

Recent in Nordic blog

nRF52840-DK Range Testing With BLE, ZigBee and Thread Protocols at 0, 4 and 8dBm Transmit Power Settings

notsane0

Range testing of any RF scheme is inherently limited by the RF environment, antenna design, tuning and many other factors. The usefulness of range testing is to provide a basis for comparison while keeping…
- 28 Dec 2018
Thingy:52 MOSFET Usage

gamnes

This blog post describes how you can take advantage of the 4 MOSFET's on the Thingy:52. DISCLAIMER: Please verify all information that is used/retrieved from this blog post. Some of the information…
- 27 Dec 2018
Using the Power Profiling Kit to measure Current Draw on an External Device

notsane0

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018
What impact does the deprecation and withdrawal of Bluetooth Core specification v4.0 and v4.1 have on your current and future products?

Petter Myhre

This blog was last updated 17.01.2019. The Bluetooth Special Interest Group (SIG) recently announced the deprecation and withdrawal of Bluetooth Core specifications v4.0 and v4.1. For products that are…
- 30 Oct 2018
The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018

Nordic DevZone

DevZone monthly Leaderboard

about nrf24le1debug problem View Voters Login to vote on this thread 0 Login to vote on this thread 0

Communication timeout. Emulator did not re-enumerate View Voters Login to vote on this thread 0 Login to vote on this thread 0

APP which support to conect 8 or more BLE peripherals View Voters Login to vote on this thread 0 Login to vote on this thread 0

nRF51xxx debugging with BDI debugger View Voters Login to vote on this thread 0 Login to vote on this thread 0

Scaner Design uisng nRF24L01 View Voters Login to vote on this thread 0 Login to vote on this thread 0

nRF52840-DK Range Testing With BLE, ZigBee and Thread Protocols at 0, 4 and 8dBm Transmit Power Settings

Thingy:52 MOSFET Usage

Using the Power Profiling Kit to measure Current Draw on an External Device

What impact does the deprecation and withdrawal of Bluetooth Core specification v4.0 and v4.1 have on your current and future products?

The S132 v5.1.0 is now production tested on nRF52810

Adding custom commands to a BLE example using Nordic UART Service

about nrf24le1debug problem
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Communication timeout. Emulator did not re-enumerate
View Voters Login to vote on this thread 0 Login to vote on this thread
0

APP which support to conect 8 or more BLE peripherals
View Voters Login to vote on this thread 0 Login to vote on this thread
0

nRF51xxx debugging with BDI debugger
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Scaner Design uisng nRF24L01
View Voters Login to vote on this thread 0 Login to vote on this thread
0