Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
MODBUS not working, RS-485 0

Hello, I'm having problems trying to make the MODBUS RTU Client code work on my board. I'm devoloping with nrf Connect SDK v2.1.0, using Visual Studio Code. The board...
- development
- software
- documentation
- configuration
- C
- nrf52832
10 views

0 replies

Started 23 minutes ago
by Pepe Sanches
Not Answered
DMA buffers switching with SPI and TIMERS via PPI 0

While collecting 2-byte samples via SPI4 (with a 32 MHz clock) using PPI and timers—one triggering transfers at 400 kHz and another handling an interrupt every 512 samples...
- development
- easydma
- software
- dma
- spi
- zephyr
- nRF5340
5 views

0 replies

Started 25 minutes ago
by Michal Mrowiec
Not Answered
Use keypad for wakeup (kbd_matrix) from deep sleep (sys_poweroff) 0

I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
10 views

0 replies

Started 34 minutes ago
by Crox
Not Answered
Writing to flash memory 0

Hi, I'm using an nRF52810 on a custom board and I'm using softdevice s112_nrf52_7.2.0_softdevice.hex. I want to write some information (just 4 bytes) to flash memory,...
- development
- software
- flash
- nrf52810
8 views

0 replies

Started 38 minutes ago
by Kenneth_CBS
Not Answered
Unable to configure nRF Sniffer for 802.15.4 for ZigBee 0

Hello All, I wanted to sniff ZigBee Packets using Wireshark SW, I am following the below link for the setup, https://docs.nordicsemi.com/bundle/ug_sniffer_802154/page...
7 views

0 replies

Started 39 minutes ago
by UVP

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020