Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
In the smp_svr project, OTA fails after explicitly setting CONFIG_BT_SMP=y. 0

SDK v3.2.0 SMP Service: INITIALZING Always show " INITIALZING ".
1 view

0 replies

Started 2 minutes ago
by Leo Mo
Not Answered
NRF54L05 how to surpport CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC in bare-metal SDK 0

Hi , NRF54L05 how to surpport CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC in bare-metal SDK,and while enable mcuboot OTA DFU feature ,how to modify the configuration?Thanks.
7 views

0 replies

Started 54 minutes ago
by OPQ
Not Answered
nrf52833 scan extend adv packet 0

I am using the nrf52833 with 17.1 SDK and s140_nrf52_7.2.0_softdevice，i want to scan a scannable extend adv packets， This is what i get in the BLE_GAP_EVT_ADV_REPORT ： ...
5 views

0 replies

Started 58 minutes ago
by xinzhenXU
Not Answered
UART, I2C, SPI, PDM and USB Pin Mapping for nRF5340 (NRF5340-QKAA-R7) 0

Hello Nordic Team, We are working with the NRF5340-QKAA-R7 and need clarification on which physical pins can be used for UART, I2C, SPI, PDM and USB interfaces . We have...
12 views

0 replies

Started 4 hours ago
by Mohammed Hashir P
Not Answered
Linux USB ports 0

I have a nrf9160dk that drives a screen via SPI, using an IT8951 controller. The firmware driving the screen works fine if I plug the USB cable on a power bank or using MS...
13 views

0 replies

Started 17 hours ago
by amelio

Recent in the DevZone Blog

Using the Power Profiling Kit to measure Current Draw on an External Device

notsane0

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018
What impact does the deprecation and withdrawal of Bluetooth Core specification v4.0 and v4.1 have on your current and future products?

Petter Myhre

This blog was last updated 17.01.2019. The Bluetooth Special Interest Group (SIG) recently announced the deprecation and withdrawal of Bluetooth Core specifications v4.0 and v4.1. For products that are…
- 30 Oct 2018
The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018