Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
GRTC resets after sys_poweroff when using MCUboot (ncs 3.1.0) 0

Hello Nordic team, We are using the GRTC on the nRF54L15 , and we are observing the following behavior: When MCUboot is enabled , the GRTC (likely backed by SYSCOUNTER...
28 views

0 replies

Started 9 hours ago
by ddiassword
Not Answered
AT Command Documentation for NTN Development on nRF9151-LACA-A1A-R (SLM Mode) 0

Hi everyone, I’m currently working with the nRF9151-LACA-A1A-R module, developing NTN communication features using SLM mode. However, I haven’t been able to find any documentation...
26 views

0 replies

Started 9 hours ago
by felipe.eaware
Not Answered
HTTP Client + W5500 on nRF5340: Works with IP but fails with domain names (DNS resolution fails) 0

Hi everyone, I’m trying to use the HTTP client sample from NCS v3.0.2 with a W5500 Ethernet shield on an nRF5340. DHCP works fine, and I can successfully POST and GET using...
10 views

0 replies

Started 13 hours ago
by Haris Iqbal
Not Answered
PPK II reliability and interaction with DC/DC converters 0

Hi, We've been using the PPK II for basically every IoT project we've carried out in the last few years, and it has been an incredibly useful tool. Our standard use case...
17 views

0 replies

Started 13 hours ago
by ecasado_iz
Not Answered
GPS CN0 Test 0

If you have tested the nRF9151's GPS with the CMW100 or IQ station. We need to know: 1. What test waveform file is required? 2. Should we use the ARB file or the CW waveform...
12 views

0 replies

Started 14 hours ago
by Bruce Chen

Recent in the DevZone Blog

Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018
Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018