Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Matter Thermostat build fail for nRF54L15DK 0

I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
28 views

0 replies

Started 15 hours ago
by Sunil vignesh
Not Answered
Cmake Errors while building code in nrf5340dk 0

when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
- development
- code
- Evaluation
- configuration
- zephyr
- nRF5340
30 views

0 replies

Started 16 hours ago
by Gouri
Not Answered
Understanding "S1-U data transfer: Not supported" with nRF9160 on Private NB-IoT (Network Owner Claims Modem Origin) 0

Hello, I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network. However, when reviewing the logs from the private network...
64 views

0 replies

Started 1 day ago
by l0cszp
Not Answered
nRF54L15 continuous wave mode 0

Hello, How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
42 views

0 replies

Started 1 day ago
by kitc22
Not Answered
Adding Actinius Icarus nRF9160 as LTE device in nRF cloud 0

Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud. I already know my board IMEI (I got it by flashing the AT client sample and then...
37 views

0 replies

Started 1 day ago
by Rocio Cabral

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017
Bluetooth 5 2Mbps Demo with nRF52 Series and Samsung Galaxy S8

John Leonard

Bluetooth 5 - now arriving in smartphones As we know, Bluetooth 5 was launched last December by the Bluetooth SIG. The nRF52 Series from Nordic have always had Bluetooth 5 and its arrival in the mix for…
- 9 May 2017
Setting up Segger on a mac or pc and debug - step by step for humans

Lola

Most guides out there are unclear and made for machines. Here is a full guide how to setup Segger for mac OS X with some example project from the SDK ( or even a PC but not tested), and also how to debug…
- 5 May 2017
FreeRTOS threads preview with J-Link, GDB/Eclipse

Radoslaw Koppel

Short note how to make FreeRTOS program debugging with eclipse little simpler. If you are looking the information how to configure the whole environment see this post: https://devzone.nordicsemi.com/tutorials…
- 11 Apr 2017