Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF5_SDK_16 : NRF_SECTION_DEF() / NRF_SECTION_START_ADDR() : unnecessary ‘&’ in the definition 0

From "nrf_section.h" (__GNUC__): Example for the section name " log_const_data ": NRF_SECTION_DEF(log_const_data, nrf_log_module_const_data_t) //: extern nrf_log_module_const_data_t...
- development
- software
- s132
- nrf52832
0 views

0 replies

Started 1 hour ago
by dwm
Not Answered
nRF52840 DK dual virtual COM 0

Dear, I am using both nRF52840 UART (UART0 and UARTE1) on the nRF52840 DK. The default pin assignement is used, such as UART0 pins are TX/RX 0.6 & 0.5 and UARTE1...
0 views

0 replies

Started 1 hour ago
by Nop Microwave
Not Answered
How can I add color control capabilities to the matter_bulb example? 0

"I added an endpoint called Matter Extended Color Light to the matter_bulb example. After compiling and flashing the firmware, HomeKit only recognizes and creates two dimmable...
0 views

0 replies

Started 1 hour ago
by OllLlllO
Not Answered
Clarification on nPM1300 Current Measurements 0

Hello, I have a few questions regarding the nPM1300 current measurements: As far as I understand, there are two ways to trigger a current measurement: By writing...
0 views

0 replies

Started 2 hours ago
by Badr
Not Answered
Tone of Tolerance (Power) value for nrf52832 0

Hi, we had used nRF52832 in our product. Our product is undergoing FCC & IC certification. FCC & IC regulatory body had requested to provide Tone of tolerance (Power)...
0 views

0 replies

Started 3 hours ago
by Rahul Wagh

Recent in Nordic blog

Fast Production Screening based upon Bluetooth DTM

Ken L

The challenge As a product is getting into the production phase, the need of a fast and standalone screening facility on the production line arises. Here I'm introducing a production screening setup…
- 9 Dec 2016
I am developing an open source sensor beacon board

zelin

I am developing an open source sensor beacon board named: YS-Beacon which contains: nRF52832 DAPLink - LPC11U35 9-Axis Motion Sensor Ambient Light Sensor、Proximity Sensor and 3D-Gesture Sensor with…
- 2 Dec 2016
nRF52 Rocket: Part I – Introduction to Model Rocketry and its UX Problem

Tony Wu

Official Launch Video Welcome to this 2 or 3-part blog about the nRF52 Rocket, a BLE-enabled model rocket, which you’ve just seen soaring through the air in the video above. In the first part of blog…
- 21 Nov 2016

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022