Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Pin connection for UART and SPI for Thing:91 0

Hello, I need to connect the Thingy:91 to an MCU via UART and/or SPI bus. I need help to identify the pins for communications for: SPI: CSK, CS, MISO, and MOSI UART...
- Evaluation
- spi
- Other
- hardware
9 views

0 replies

Started 1 hour ago
by RamizB
Not Answered
When using external flash, calling Device_is_read returns a failure 0

Hi: I use ncs v2.8.0, using external flash(w25q128). this is test flash project. And this log: Device_is_read returns a failure. But flash read/write successful...
13 views

0 replies

Started 3 hours ago
by john.liu
Not Answered
Sniffer fails to catch packets when running radio_test. 0

Hello, I wanted to verify if two devices are communicating by using a sniffer. After running the radio_test example, I set up parameters for each transmitter and receiver...
20 views

0 replies

Started 7 hours ago
by kim_mj
Not Answered
upgrade ncs from v2.6.0 to v2.9.0, building gets errors 0

hello, my code was built under ncs v2.6.0 and tool chain 2.6.0 without issue, I upgrade them to v2.9.0, then I get these errors, can not figure out how to fix them. could...
14 views

0 replies

Started 8 hours ago
by danny0007
Not Answered
Fuel Gauge Battery Profiling Configuration 0

Hi, I'm new to fuel gauging and battery profiling and am trying to understand the process and the parameters used. Is there a description of how a battery model is created...
17 views

0 replies

Started 9 hours ago
by ralphjy

Recent in Nordic blog

BLEBot - a phone controlled/autonomous 2WD robot based on nRF51822

Mahesh Venkitachalam

In this project, we will build a two-wheeled robot based on the Nordic nRF51822 BLE SoC. Motor control for the two wheels of the robot will be done using an L293D chip. The robot can be controlled using…
- 12 Oct 2015
Toys 2.0: Smart Toy Robots use the nRF51 based Cannybot Brain

Wayne

The Cannybot Brain is a robotics controller board that uses the Nordic Semiconductor nRF51822 at its core. The board has been developed by Cannybots Limited in Cambridge, UK. One of Cannybots core values…
- 6 Oct 2015
Programming services, HI-LO Electronics in corporation with Nordic Semiconductor AS

HILO

In corporation with Nordic Semiconductor we are happy to announce our programming services! Your flexible programming center is based in Gothenburg, Sweden at HI-LO Electronics AB Advantages with pre…
- 30 Sep 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019