Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Dect NR+ Subcarrier scaling factor and subslot 0

Hello, I am working with the NRF9151 DK on DECT NR+ and I want to change the subcarrier scaling factor and subslot value in the hello_dect example. However, I am not sure...
15 views

0 replies

Started 16 hours ago
by emindrmus
Not Answered
BLE_MESH: dynamically change between node and relay mode 0

Hi, We are planning a new project that needs to use very low power. Since relay mode uses more power than simple node, can we turn off relay mode on all nodes until an event...
16 views

0 replies

Started 16 hours ago
by atlesilgjerd
Not Answered
Coded PHY on BLE sniffer not working? 0

I'm trying to use nordic's BLE sniffer on a nRF52833-DK. I have programmed it with the firmware "sniffer_nrf52833dk_nrf52833_4.1.1.hex". I've then tried both the command...
15 views

0 replies

Started 17 hours ago
by Emil Lenngren
Not Answered
nRF Connect SDK VScode mcuboot settings 0

Hi, for my custom device with nRF52840 and nRF Connect SDk v.2.8.0with VScode I want to add bootloader so that I can pass firmware to it through USB cable. I want a simple...
26 views

0 replies

Started 20 hours ago
by masterLee
Not Answered
VBUS supply before system ON on normal voltage mode nRF52833 0

1. Our system is configured with circuit config3 of the nRF52833 WLCSP, where an external power supply of 1.8V is applied to VDD. Power sequence : USB connection -> VBUS...
19 views

0 replies

Started 23 hours ago
by deep_dive

Recent in Nordic blog

Exploring the benefits of MCUboot's compressed image support

Ali Aljaani

The MCUboot compressed image support, introduced in nRF Connect SDK v2.8.0, offers a significant advancement for developers working with non-volatile memory constraints. This feature frees up a substantial…
- 3 Dec 2024
nRF54L Series now widely available for development

Petter Myhre

Since the announcement of the nRF54L15 SoC, we have been working hard to get the quality up to our standard, while adding support in our software and tools to improve the developer experience and ease…
- 13 Nov 2024
Getting started with NR+ PHY

Heidi-Irene Harvey Sollie

The DECT NR+ standard is steadily maturing, and with the release of nRF Connect SDK v2.7.0, we are inching closer to seeing NR+ commercial products on the market. If you want to get up to speed on NR+ quickly…
- 20 Jun 2024

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022