nRF52840 dongle isnt showing up in the connected devices section on VS code.

[qurese1]

Hi, 

I've been trying to connect the nRF53480 dongle to VS Code. I have followed the necessary tutorials and ensured I have compatible and updated nrf Connect SDK and toolchain versions. However, the toolchain installation is always stuck on loading on VS code (amber colour) and always fails to connect. Subsequently, I don't see any device connected in connected devices. I know it is not a hardware problem, as the dongle turns either green or red when i connect it and in the RSSI viewer, I can see the live connection as well. I am unsure what to do next. 

I have also reinstalled and installed it multiple times from scratch, but it doesn't seem to fix the problem. 

The purpose of my work right now is to run a continuous wave through the dongle and be able to visualize it, but I am unable to get past the configuration/setting up stage. 

Any ideas on how I can fix this? 

[Maria Gilje]

Hello,

Subsequently, I don't see any device connected in connected devices.

The nRF52840 Dongle will not show up in VS Code because it does not have an on-board debugger. It can be programmed with the Programmer application in nRF Connect for Desktop. You can find the instructions for programming it here, and the user guide for the nRF52840 Dongle here.

I've been trying to connect the nRF53480 dongle to VS Code. I have followed the necessary tutorials and ensured I have compatible and updated nrf Connect SDK and toolchain versions. However, the toolchain installation is always stuck on loading on VS code (amber colour) and always fails to connect.

Please use the "Generate support information" option in the Welcome tab in the nRF Connect for VS Code extension and share the output in a reply.

I have followed the necessary tutorials

Was this the tutorial you followed? Installing automatically

If yes, please share the system report from the Toolchain manager. This is found under About -> Support.

Best regards,

Maria

[qurese1]

Hello, 
- here is the system report from the toolchain manager. 

- yes, the link to tutorial you mentioned is the one i have used. 
- for "share the output in a reply" is that referring to the toolchain being stuck on "loading"? 
- lastly, where can i find the DFU in nrf Connect 

these are the only apps i see here, is there an external way of getting the DFU as the on-board debugger?

Best Regards, 

[qurese1]

Naeem Maroof said:

I don't have any other suggestion at the moment, but it could be improper installation if you were never able to start any sample. You may consider installing another version of ncs (e.g. ncs v2.3.0 along with the toolchain). It might take some time before installation gets completed. Please update the SDK and toolchain before using.

since my laptop is windows 11, could that be the reason why the toolchain isn't loading??

[qurese1]

Naeem Maroof said:

a) were you able to use NCS2.4.0 previously? Or it is the same symptoms from the start (when you first time installed NCS)

b) did you try any other version of NCS (like 2.3.0)?

c) can you uninstall the NCS and completely remove the toolchain and sdk folders and then start from scratch. Also, try another version of the SDK as well.

I have once again uninstalled all relate SDKs and toolchains and will try the aforementioned versions to see if it works!

[qurese1]

Naeem Maroof said:

a) were you able to use NCS2.4.0 previously? Or it is the same symptoms from the start (when you first time installed NCS)

 

since my laptop is 64 bit only these versions of nrf connect are available

[Naeem Maroof]

Hi Emaan,

I am also surprised to look at this, but yes, as per the "supported OS" information of the NCS, it may or may not work for your operating system.

[Naeem Maroof]

Yes, you may install it as this is the supported version for x64, but as you have pointed out that as per the OS requirement for NCS, windows 11 is Tier 3, and the NCS may or may not work on it.