LIS2DH12 device is not ready issue

[Jareena]

Hi,

I have added .overlay file as below mentioned 

&spi0 {
    status = "okay";   
    acc_lis2dh_spi: lis2dh@0 {
        compatible = "st,lis2dh";
        reg = <0>;
        spi-max-frequency = <10000000>;
        irq-gpios = <&gpio1 1 2>;
        label = "LIS2DH";
    };
};

And i have added my prj.config file as mentioned below.

CONFIG_STDOUT_CONSOLE=y
CONFIG_SPI=y
CONFIG_SENSOR=y
CONFIG_CBPRINTF_FP_SUPPORT=y
CONFIG_LIS2DH=y
CONFIG_LIS2DH_TRIGGER_GLOBAL_THREAD=y
CONFIG_PRINTK=y

And I am facing issue is
Device LIS2DH is not ready with nrf52840dk.

So, can you please, help me with it.

Thanks & Regards,

Shaik Jareena.

[Jared]

Hi,

Where do you specify the SPI pins such as SCLK, CS, MOSI, MISO?

regards

Jared 

[Jareena]

Hi,

I have added this pins like below mentioned and can you please, find this below.

&spi1 {
    status = "okay";
    compatible = "nordic,nrf-spi";
    sck-pin = <0x23>;
    mosi-pin = <0x24>;
    miso-pin = <0x25>;
    cs-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
    
    acc_lis2dh_spi: lis2dh@0 {
        compatible = "st,lis2dh";
        reg = <0>;
        spi-max-frequency = <10000000>;
        irq-gpios = <&gpio1 2 1>;
        label = "LIS2DH";
    };
};

And after this also, I am facing same issue device is not ready issue.

Thanks & Regards,

Shaik Jareena.

[Jared]

Hi,

If you probe the SCLK, do you see any clock activity when you start the program?

regards

Jared 

[Jareena]

Hi,

I forgot to mention that when I am adding like this below 

&spi1 {
    status = "okay";
    compatible = "nordic,nrf-spi";
    sck-pin = <0x23>;
    mosi-pin = <0x24>;
    miso-pin = <0x25>;
    cs-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
    
    acc_lis2dh_spi: lis2dh@0 {
        compatible = "st,lis2dh";
        reg = <0>;
        spi-max-frequency = <10000000>;
        irq-gpios = <&gpio1 2 1>;
        label = "LIS2DH";
    };
};

I am facing cmake errors and i am not able to build even 

[{
	"resource": "/c:/ncs/v2.5.1/zephyr/cmake/modules/dts.cmake",
	"owner": "nrf-connect",
	"severity": 8,
	"message": "CMake Error at C:/ncs/v2.5.1/zephyr/cmake/modules/dts.cmake:279 (message):",
	"source": "cmake",
	"startLineNumber": 279,
	"startColumn": 1,
	"endLineNumber": 279,
	"endColumn": 2147483647
}]

So, If i solve this only I can build my lis2dh12 application. So, can you please provide the correct .overlay file for nrf52840.

Your help is more Appreciable.

Thanks & Regards,

Shaik Jareena.

[Jared]

What build error do you get?

regards

Jared 

[Jareena]

Hi,

I am facing below mentioned errors. Can you please, help me with it.

Building lis2dh
C:\Windows\system32\cmd.exe /d /s /c "west build --build-dir c:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build c:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh"

[0/1] Re-running CMake...
Loading Zephyr default modules (Zephyr base (cached)).
-- Application: C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh
-- CMake version: 3.20.5
-- Cache files will be written to: C:/ncs/v2.5.1/zephyr/.cache
-- Zephyr version: 3.4.99 (C:/ncs/v2.5.1/zephyr)
-- Found west (found suitable version "1.1.0", minimum required is "0.14.0")
-- Board: nrf52840dk_nrf52840
-- Found host-tools: zephyr 0.16.1 (C:/ncs/toolchains/c57af46cb7/opt/zephyr-sdk)
-- Found toolchain: zephyr 0.16.1 (C:/ncs/toolchains/c57af46cb7/opt/zephyr-sdk)
-- Found BOARD.dts: C:/ncs/v2.5.1/zephyr/boards/arm/nrf52840dk_nrf52840/nrf52840dk_nrf52840.dts
-- Found devicetree overlay: C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/nrf52840dk_nrf52840.overlay
-- Found devicetree overlay: nrf52840dk_nrf52840.overlay
devicetree error: 'sck-pin' appears in /soc/spi@40004000 in C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/zephyr.dts.pre, but is not declared in 'properties:' in C:/ncs/v2.5.1/zephyr/dts/bindings\spi\nordic,nrf-spi.yaml
-- In: C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr, command: C:/ncs/toolchains/c57af46cb7/opt/bin/python.exe;C:/ncs/v2.5.1/zephyr/scripts/dts/gen_defines.py;--dts;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/zephyr.dts.pre;--dtc-flags;'-Wno-unique_unit_address_if_enabled';--bindings-dirs;C:/ncs/v2.5.1/nrf/dts/bindings;C:/ncs/v2.5.1/zephyr/dts/bindings;--header-out;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/include/generated/devicetree_generated.h.new;--dts-out;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/zephyr.dts.new;--edt-pickle-out;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/edt.pickle;--vendor-prefixes;C:/ncs/v2.5.1/nrf/dts/bindings/vendor-prefixes.txt;--vendor-prefixes;C:/ncs/v2.5.1/zephyr/dts/bindings/vendor-prefixes.txt
CMake Error at C:/ncs/v2.5.1/zephyr/cmake/modules/dts.cmake:279 (message):
gen_defines.py failed with return code: 1
Call Stack (most recent call first):
C:/ncs/v2.5.1/zephyr/cmake/modules/zephyr_default.cmake:129 (include)
C:/ncs/v2.5.1/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:66 (include)
C:/ncs/v2.5.1/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:97 (include_boilerplate)
CMakeLists.txt:8 (find_package)

-- Configuring incomplete, errors occurred!
See also "C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/CMakeFiles/CMakeOutput.log".
See also "C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/CMakeFiles/CMakeError.log".
ninja: error: rebuilding 'build.ninja': subcommand failed
FAILED: build.ninja
C:\ncs\toolchains\c57af46cb7\opt\bin\cmake.exe --regenerate-during-build -SC:\ncs\v2.5.1\zephyr\samples\sensor\lis2dh -BC:\ncs\v2.5.1\zephyr\samples\sensor\lis2dh\build
FATAL ERROR: command exited with status 1: 'C:\ncs\toolchains\c57af46cb7\opt\bin\cmake.EXE' --build 'c:\ncs\v2.5.1\zephyr\samples\sensor\lis2dh\build'

* The terminal process terminated with exit code: 1.
* Terminal will be reused by tasks, press any key to close it.

* Executing task: nRF Connect: Build [clean]: lis2dh/build (active)

Building lis2dh
C:\Windows\system32\cmd.exe /d /s /c "west build -t clean --build-dir c:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build"

-- west build: running target clean
[0/1] Re-running CMake...
Loading Zephyr default modules (Zephyr base (cached)).
-- Application: C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh
-- CMake version: 3.20.5
-- Cache files will be written to: C:/ncs/v2.5.1/zephyr/.cache
-- Zephyr version: 3.4.99 (C:/ncs/v2.5.1/zephyr)
-- Found west (found suitable version "1.1.0", minimum required is "0.14.0")
-- Board: nrf52840dk_nrf52840
-- Found host-tools: zephyr 0.16.1 (C:/ncs/toolchains/c57af46cb7/opt/zephyr-sdk)
-- Found toolchain: zephyr 0.16.1 (C:/ncs/toolchains/c57af46cb7/opt/zephyr-sdk)
-- Found BOARD.dts: C:/ncs/v2.5.1/zephyr/boards/arm/nrf52840dk_nrf52840/nrf52840dk_nrf52840.dts
-- Found devicetree overlay: C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/nrf52840dk_nrf52840.overlay
-- Found devicetree overlay: nrf52840dk_nrf52840.overlay
devicetree error: 'sck-pin' appears in /soc/spi@40004000 in C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/zephyr.dts.pre, but is not declared in 'properties:' in C:/ncs/v2.5.1/zephyr/dts/bindings\spi\nordic,nrf-spi.yaml
-- In: C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr, command: C:/ncs/toolchains/c57af46cb7/opt/bin/python.exe;C:/ncs/v2.5.1/zephyr/scripts/dts/gen_defines.py;--dts;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/zephyr.dts.pre;--dtc-flags;'-Wno-unique_unit_address_if_enabled';--bindings-dirs;C:/ncs/v2.5.1/nrf/dts/bindings;C:/ncs/v2.5.1/zephyr/dts/bindings;--header-out;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/include/generated/devicetree_generated.h.new;--dts-out;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/zephyr.dts.new;--edt-pickle-out;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/edt.pickle;--vendor-prefixes;C:/ncs/v2.5.1/nrf/dts/bindings/vendor-prefixes.txt;--vendor-prefixes;C:/ncs/v2.5.1/zephyr/dts/bindings/vendor-prefixes.txt
CMake Error at C:/ncs/v2.5.1/zephyr/cmake/modules/dts.cmake:279 (message):
gen_defines.py failed with return code: 1
Call Stack (most recent call first):
C:/ncs/v2.5.1/zephyr/cmake/modules/zephyr_default.cmake:129 (include)
C:/ncs/v2.5.1/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:66 (include)
C:/ncs/v2.5.1/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:97 (include_boilerplate)
CMakeLists.txt:8 (find_package)

-- Configuring incomplete, errors occurred!
See also "C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/CMakeFiles/CMakeOutput.log".
See also "C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/CMakeFiles/CMakeError.log".
FAILED: build.ninja
C:\ncs\toolchains\c57af46cb7\opt\bin\cmake.exe --regenerate-during-build -SC:\ncs\v2.5.1\zephyr\samples\sensor\lis2dh -BC:\ncs\v2.5.1\zephyr\samples\sensor\lis2dh\build
ninja: error: rebuilding 'build.ninja': subcommand failed
FATAL ERROR: command exited with status 1: 'C:\ncs\toolchains\c57af46cb7\opt\bin\cmake.EXE' --build 'c:\ncs\v2.5.1\zephyr\samples\sensor\lis2dh\build' --target clean

* The terminal process terminated with exit code: 1.
* Terminal will be reused by tasks, press any key to close it.

* Executing task: nRF Connect: Build: lis2dh/build (active)

Building lis2dh
C:\Windows\system32\cmd.exe /d /s /c "west build --build-dir c:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build c:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh"

[0/1] Re-running CMake...
Loading Zephyr default modules (Zephyr base (cached)).
-- Application: C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh
-- CMake version: 3.20.5
-- Cache files will be written to: C:/ncs/v2.5.1/zephyr/.cache
-- Zephyr version: 3.4.99 (C:/ncs/v2.5.1/zephyr)
-- Found west (found suitable version "1.1.0", minimum required is "0.14.0")
-- Board: nrf52840dk_nrf52840
-- Found host-tools: zephyr 0.16.1 (C:/ncs/toolchains/c57af46cb7/opt/zephyr-sdk)
-- Found toolchain: zephyr 0.16.1 (C:/ncs/toolchains/c57af46cb7/opt/zephyr-sdk)
-- Found BOARD.dts: C:/ncs/v2.5.1/zephyr/boards/arm/nrf52840dk_nrf52840/nrf52840dk_nrf52840.dts
-- Found devicetree overlay: C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/nrf52840dk_nrf52840.overlay
-- Found devicetree overlay: nrf52840dk_nrf52840.overlay
devicetree error: 'sck-pin' appears in /soc/spi@40004000 in C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/zephyr.dts.pre, but is not declared in 'properties:' in C:/ncs/v2.5.1/zephyr/dts/bindings\spi\nordic,nrf-spi.yaml
-- In: C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr, command: C:/ncs/toolchains/c57af46cb7/opt/bin/python.exe;C:/ncs/v2.5.1/zephyr/scripts/dts/gen_defines.py;--dts;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/zephyr.dts.pre;--dtc-flags;'-Wno-unique_unit_address_if_enabled';--bindings-dirs;C:/ncs/v2.5.1/nrf/dts/bindings;C:/ncs/v2.5.1/zephyr/dts/bindings;--header-out;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/include/generated/devicetree_generated.h.new;--dts-out;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/zephyr.dts.new;--edt-pickle-out;C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/zephyr/edt.pickle;--vendor-prefixes;C:/ncs/v2.5.1/nrf/dts/bindings/vendor-prefixes.txt;--vendor-prefixes;C:/ncs/v2.5.1/zephyr/dts/bindings/vendor-prefixes.txt
CMake Error at C:/ncs/v2.5.1/zephyr/cmake/modules/dts.cmake:279 (message):
gen_defines.py failed with return code: 1
Call Stack (most recent call first):
C:/ncs/v2.5.1/zephyr/cmake/modules/zephyr_default.cmake:129 (include)
C:/ncs/v2.5.1/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:66 (include)
C:/ncs/v2.5.1/zephyr/share/zephyr-package/cmake/ZephyrConfig.cmake:97 (include_boilerplate)
CMakeLists.txt:8 (find_package)

-- Configuring incomplete, errors occurred!
See also "C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/CMakeFiles/CMakeOutput.log".
See also "C:/ncs/v2.5.1/zephyr/samples/sensor/lis2dh/build/CMakeFiles/CMakeError.log".
FAILED: build.ninja
C:\ncs\toolchains\c57af46cb7\opt\bin\cmake.exe --regenerate-during-build -SC:\ncs\v2.5.1\zephyr\samples\sensor\lis2dh -BC:\ncs\v2.5.1\zephyr\samples\sensor\lis2dh\build
ninja: error: rebuilding 'build.ninja': subcommand failed
FATAL ERROR: command exited with status 1: 'C:\ncs\toolchains\c57af46cb7\opt\bin\cmake.EXE' --build 'c:\ncs\v2.5.1\zephyr\samples\sensor\lis2dh\build'

* The terminal process terminated with exit code: 1.
* Terminal will be reused by tasks, press any key to close it.

Thanks & Regards,

Shaik Jareena.

[Jared]

Hi,

You have to use pin ctrl when you add the pins, for example in the JESD216 sample:

And the board file for nrf52840dk_nrf52840-pinctrl.dtsi

regards

Jared

[Jareena]

Hi,

Thank you for your response, I have one doubt about pin connections now I have to provide the pin connections according to the LIS2DH12 and nRF52840 pins. So, I have to change the pins If I am using JES2D16 reference sample but I do not have schematic of LIS2DH12+nRF52840 pin connections, I searched for it in Nordic website but i did not find it.

If you have schematic of LIS2DH12+nRF52840 pin connections schematic, can you please, share with me.

Thanks & Regards,

Shaik Jareena.

[Jared]

Hi,

I provided the previous sample so that you can see how you should setup miso, sclk, and mosi using pinctrl. The CS pin is setup as a node by itself in the SPI node structure. I'm not sure what schematic you're asking for. The LIS2DH12 is not embedded on the nRF52840 DK. What pins have you physically connected the LIS2DH12 to the nRF52840 on?

regards

Jared