Unable to decrypt Zigbee Shell traffic in Wireshark

[Wayne]

Hi,

I'm using nRF Connect v2.6.2 with Wireshark (3.6) and it is setup with the nRF sniffer + Nordic network keys configured.

I can decrypt packets from another Zigbee network (Pi + SkyConnect based using the added Home Assistant network key)

I have performed a full flash erase before flashing the shell firmware on my nrf52840.

The command sequence I'm using is as follows (it is/should be re-using the Nordic example network key already configured in Wireshark):

```

bdb start
bdb factory_reset

# nRF HW Reset at this point and reconnect to shell cli

nvram disable
bdb nwkkey abcdef01234567890000000000000000
nvram enable

bdb role zc
bdb start

```

At this point any packets appearing in Wireshark are never decrypted.  

Is anyone able to help point out what steps I have missed or am I doing wrong?

Thank you,

Wayne

[Marte Myrvold]

Hi Wayne,

Can you explain why you are starting the network, factory resetting the device, and disabling/enabling NVRAM before starting the network again?

Are you able to decrypt the packets if you simply configure the network key, configure the device as coordinator, and then start the network?

bdb nwkkey abcdef01234567890000000000000000
bdb role zc
bdb start

Best regards,
Marte

[Wayne]

Hi,

I've also tried setting the network key in the shell main.c hoping this would be the default key instead of any randomly assigned one:

int main(void)

{

LOG_INF("Starting Zigbee shell application");

 

...

uint8_t network_key[ZB_CCM_KEY_SIZE] = {0xab, 0xcd, 0xef, 0x01, 0x23, 0x45, 0x67, 0x89, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00};

zb_secur_setup_nwk_key(network_key,0);

LOG_INF("Zigbee shell application started");

return 0;

}

Although this doesn't work either, but it's not clear to me that this actually takes effect and is not overwritten by any other zigbee startup code.

All the best

Wayne

[Wayne]

Hi Marte,

The network key is set after the erase, I have just tried a test with the sniffer running prior to my testing. I'm going to upgrade to WS 4.x to see if that makes a difference.

What are "install codes"?

Thanks

Wayne

[Marte Myrvold]

Hi Wayne,

Install code is a security feature in Zigbee that allows you to configure the network so that only devices with install codes can join it. When using this, the install code and extended address of a joining device must be added to the coordinator before the device can join, and during joining, the device's install code is used to generate a unique trust center link key for the device. If you were using this, it could explain why the packets are encrypted since the sniffer would not be able to decrypt the packets of a network using install codes with just the network key.

With Zigbee shell, you can manually enable and add install codes, but it does not seem like you are doing so, so you can just ignore my question regarding it

Best regards,
Marte

[Wayne]

Hi Marte,

Thanks for letting know.  

Please could you also let me know which version of: the nRF Connect SDK, Wireshark and the nRF MCU you are using to test please ?

Thanks

Wayne

[Marte Myrvold]

Hi Wayne,

I tested with nRF Connect SDK v2.6.1, Wireshark v4.2.4 on Ubuntu 22.04, and nRF52840 DK.

Best regards,
Marte

[Wayne]

Hi Marte,

Thanks for your help, I'm able to see decrypted packets.

All the best

Wayne