Cryptocell and usb

[AintMina]

I was building the "console" sample code found in zephyr for my custom nrf52840 board and I managed to get it to work. But as soon as cryptocell gets enabled, it doesn't work anymore.

Q1:  Why doesn't the devicetree find "nordic,cryptocell"? I get a warning like this: Unknown node type "nordic,cryptocell"

- This also applies to nrf52840 Dongle and DK.

Q2: Cryptocell is enabled by default in nrf52840 devicetree which gets applied to all the boards (like nrf52840dongle and nrf52840dk and my custom board which uses nrf52840dongle as template). But this breaks the usb communication with the "console" sample on my custom board (It does build though).

- I can't test it with other boards since I only have nrf52dk and it doesn't support usb.

- I'm flashing it through mcuboot so I don't have access to debugger and I'm scared to use the nrf52dk as debugger since it already has bricked 3/5 devices.

Q3: The acl node has also a warning: Address range collides with flash-controller@4001e000 (both start at 0x4001e000)

- But it still works with it enabled.

I'm running Manjaro kde with linux66 kernel, v2.6.1 toolchain with v2.6.1 SDK installed through vscode extension.

This is the configuration which works:

And prj.conf:

CONFIG_USB_DEVICE_STACK=y
CONFIG_USB_DEVICE_PRODUCT="Testing"
CONFIG_USB_DEVICE_PID=0x0851
CONFIG_USB_DEVICE_VID=0x884E
CONFIG_USB_DEVICE_INITIALIZE_AT_BOOT=n

CONFIG_SERIAL=y
CONFIG_CONSOLE=y
CONFIG_UART_CONSOLE=y
CONFIG_UART_LINE_CTRL=y

 

And board defconfig:

CONFIG_SOC_SERIES_NRF52X=y
CONFIG_SOC_NRF52840_QIAA=y
CONFIG_BOARD_NRF52840_CUSTOM=y

# ??????
CONFIG_BOARD_ENABLE_DCDC=n

# 32K clock
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC=y
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC_CALIBRATION=y

# Enable MPU
CONFIG_ARM_MPU=y

# enable GPIO
CONFIG_GPIO=y

# Enable Zephyr application to be booted by MCUboot
CONFIG_BOOTLOADER_MCUBOOT=y
CONFIG_DISABLE_FLASH_PATCH=y

[dejans]

Hi, 

I would appreciate additional information and some clarifications.

Do you use a custom board with nrf52840?

I was building the "console" sample code found in zephyr for my custom nrf52840 board and I managed to get it to work. But as soon as cryptocell gets enabled, it doesn't work anymore.

Which console sample did you use? Is it maybe console over USB?
How did you enable CryptoCell?
What happens when it does not work anymore, is there any error?

Q1:  Why doesn't the devicetree find "nordic,cryptocell"? I get a warning like this: Unknown node type "nordic,cryptocell"

Did you get this warning on your custom board? Have you tried on nrf52840-dk?
"nordic,cryptocell" unknown type is probably related to some devicetree error. Can you show where and how you added "nordic,cryptocell" configuration?

Q2: Cryptocell is enabled by default in nrf52840 devicetree which gets applied to all the boards (like nrf52840dongle and nrf52840dk and my custom board which uses nrf52840dongle as template). But this breaks the usb communication with the "console" sample on my custom board (It does build though).

Can you provide information in which way is USB communication broken, what exactly happens?
Is USB communication functional on nrf52840-dk board?

Q3: The acl node has also a warning: Address range collides with flash-controller@4001e000 (both start at 0x4001e000)

This also indicates devicetree configuration issue.

But it still works with it enabled.

Can you rephrase this - what works when what is enabled? Can you show what is enabled and what happens when it works?

What is shown in provided screenshot?

Best regards,
Dejan

[AintMina]

Hi,

dejans said:

Do you use a custom board with nrf52840?

Yes, my custom board has nrf52840.

dejans said:

Which console sample did you use? Is it maybe console over USB?

It was the USB subsys sample called "console"

dejans said:

How did you enable CryptoCell?

CryptoCell is enabled by default here.

dejans said:

What happens when it does not work anymore, is there any error?

It does build without any errors, but the usb does not get initialized or recognized by my PC. It's hard to say what happens there without debugger.

dejans said:

Did you get this warning on your custom board? Have you tried on nrf52840-dk?
"nordic,cryptocell" unknown type is probably related to some devicetree error. Can you show where and how you added "nordic,cryptocell" configuration?

This warning is also shown in the nrf52840.dsti. Nrf52840-dk includes the same file. "nordic,cryptocell" is configured there and I only disabled it in my board files to make the usb code work.

dejans said:

Can you provide information in which way is USB communication broken, what exactly happens?
Is USB communication functional on nrf52840-dk board?

The only way I know it's broken is that it no longer gets recognized as a usb serial device and it is not found with NRF Connect or any other serial terminal software. I do not have access to nrf52840-dk board.

dejans said:

This also indicates devicetree configuration issue.

This I already knew. The question was why? Both of the nodes have the default configuration that come with the SDK.

dejans said:

Can you rephrase this - what works when what is enabled? Can you show what is enabled and what happens when it works?

This sample code and other codes still work when acl is enabled regarding the warning.

dejans said:

What is shown in provided screenshot?

The device configuration part of the devicetree.

BR

[AintMina]

Is this question simulator?? I have already told you these things...

You replicated the same problem as I got and still refuse to help on it...

[dejans]

Hi,

AintMina said:

I have already told you these things...

Yes, this is correct. You said that your device no longer gets recognized as a usb serial device and it is not found with NRF Connect or any other serial terminal software. I might have hoped for additional information.
Did you get any console output from the sample when cryptocell was disabled and when it was enabled?

AintMina said:

You replicated the same problem as I got and still refuse to help on it...

I am not sure if the cause of the problem in our testing is the same. I am not refusing to help you. On the contrary, I am doing further testing and having internal discussion trying to assist you. Are you able to send a software which can be run on nrf52840-dongle that would verify the behavior?

Best regards,
Dejan

[AintMina]

As I said, I don't have access to proper debugger, so the first test would be to figure out why you got the same ish problem and try to see if it's the same.

Notify when you find a solution to the problem.

BR

[Einar Thorsrud]

Hi,

Dejan is out office so I have taken over this case. Reading through this case I have problems understanding the issue. Can you please explain from the beginning the exact issue and how to reproduce it?

PS: Regarding not having a debugger, that is essential for embedded development. I assume you have at least one as you are able to program it? And using the DK as a debugger should not brick your custom board in any way. If that was the case I suggest a separate thread about that (my guess would be a that you power the board before attacking the debugger with a common ground, but this would then be an issue regardless of which debugger you connected). 

[AintMina]

...Im tired of explaining this already, read the posts... Build "console", *** works, enable cryptocell, *** no work!

if you have more questions you have to be more specific

[Einar Thorsrud]

Hi,

I have read this thread again and I am unfrortunately not able to understand what the issue is and what you want us to do. Please provide a detailed set of step by step instructions of how to reproduce this issue on a DK if you want us to look more into this. Also please note that I do not try to be difficult, it is just that I am simply not able to understand the issue from reading this thread.

[AintMina]

Clearly you didnt read ***. I have stated that I DO NOT have access to any DK board which has USB connected to the MCU.

AintMina said:

1. Installed fresh ubuntu 22.04 virtual machine

2. Installed vscode

3. Installed nrf extension pack for vscode

4. Installed 2.6.1 toolchain and SDK from vscode extension

5. Build "console" sample code for my custom boardnrf52840_custom.dts

6. Opened any serial terminal and saw the hello world message

7. Enable cryptocell in board files OR app overlay, delete build folder and build again

8. Serial terminal cannot connect to it anymore nor does lsusb find the device anymore

[AintMina]

Apparently cryptocell only works with debugger attached. Whats up with that?

[AintMina]

Great, this place removes posts...

and now the ****** board is bricked...

1. Why did the debugger erase my bootloader even though the app was built for it?

2. How did the debugger(NRF52dk) brick the board even though the code was running before bricking it?

Well, I managed to get it unbricked by messing around with gpio registers from JLinkExe. Apparently it needs to be connected with JLinkExe every time it disappears. So theres something funky going on with nrfutil...

But now I can't get the mcuboot to work and I don't have the original mcuboot config which we managed to get to work after a long battle...

[Einar Thorsrud]

Hi,

Regarding "1. Why did the debugger erase my bootloader even though the app was built for it?", I do not know how you used it, but if you do a full erase / erase all (which you often do when programming or debugging), that will erase the whole flash, includign any bootlaoders and the UICR. If you just want to re-flash the application you can seelct to use sector erase. If you are using nRF Connect for VS code for programming you can select if you want to do a full erase or not when flashing, as explaind in this post.

Regarding "2. How did the debugger(NRF52dk) brick the board even though the code was running before bricking it?" I do not know which state it what in when  you refer to it as "bricked" nor how it got there. If you can share details about how it behaved when you define it as "bricked", how it ended up in that state and hwo it receoverd, we may be able to understand more.

Generally, there is no need to use a debugger to get CrytpoCell to work, and also no conflict between CryptoCell and USB. So I suspect there are other more fundamental issues with your device or setup. I am also not able to understand the comments about debugger bricking your device. I kindly ask that you elaborate much more and provide exact details if you want specific feedback.

It seems to me that you are seeing a significant number of seemingly unrelated issues that are difficult to explain. I would suggest that you try to reduce the numer fo unkowns in the beginning by obtaining a DK so tha that you have known good hardware and test parts of your firmware on that. Then you can gradually move to your custom HW. Alternatively, there is an absolute requierment that you are able to debug your hardware.