How to configure cell battery and USB power

[Serafino Convertini]

Hi to all,

this is my first public ticket ;)

I would power a nRF52840 on my custom board both with a cell battery (specifically CR2032) and the VBUS provided by the USB connection.
I was thinking to use two schottky diode in the way showed in the attached image with using the internal DCDC of the nRF52840 as in the development board.

But I'm not sure to use schottky diode since the voltage drop on the diode. In the proposed configuration for the nRF52840, I cannot find any solution that could fit with this question.

Has anyone done this task before?

Thanks in advance

[hmolesworth]

My grandfather used schottky diodes, nowadays there are better low-drop solutions. Have a look at these:

max40203 Ideal Diode

[Serafino Convertini]

Let's assume that using MAX40203 or TCK106 (as used in nRF52840-DK). Does make sense to connect the VBUS (when present) to VDDH and VBATT (qhen present) on VDD, or should I connect the output voltage (VBUS or VBATT) to VDDH?

In both case I think I configure the nRF power stage using internal DCDC.

[hmolesworth]

The LTC4411 is a good choice if the battery is not (say) a CR2032 used for long periods; the Iq current (quiescent current to Gnd) is much higher for the LTC4411 (10s uA) compared with the MAX40203 (<1uA) which might not be important if only sparse use on the battery. Using daisy-chaned (ie both) DC-DC is also slightly less efficient, but only a few percent. This becomes an isse if (say) a 1 year shelf-life is required before use.

Both DC-DC need to be enabled by registers, and the VDD output voltage from REG0, via registers DCDEN0, REGOUT0  and DCDEN. The nRFConnect and SDK IDEs are different however, but there are examples.

[Serafino Convertini]

So your proposal is:

1. using 2x MAX40203 in place of 1x LTC4411 for the less quiescent current;
2. Connect the VBUS (via MAX40203) to VDDH;
3. Connect VBAT (via MAX40203) to VDD;
4. Enabling only the DCDCEN0;

Are you agree?

[hmolesworth]

Actually provided the coin cell is not used for long periods (the Iq issue) your latest circuit should work well as you can now set VDD to a lower voltage, typically 1.8V, which reduces current drain. However that requires all external peripheral devices (if any) on VDD or a nRF52 port pin to be specified at 1.8V supply, which is generally true nowadays. 1.8V halves the current from a 3.4V coin, and is still pretty good at 2.7V coin; I generally use 1.8V. Note if you have LEDs those require a buck-boost from the battery or a simple voltage doubler from the battery; when on battery power both of those will be required in any case.

What value is the doubled capacitor? I usually recommend low-leakage 150uF 10V on the coin cell, much higher than most reference designs.

[Serafino Convertini]

Whereas the device must work for long period, if I should use 1.8V as VDD and I have a coin cell with 3V. How could I provide a 1.8V voltage on the nRF. Should I use a DCDC stage to generate 1.8V starting from 3V (coin cell)?

[hmolesworth]

I would suggest just use your latest circuit as-is, but change the LTC411 to the MAX40203 and set VDD to 1.8V via REGOUT0. Best test before commiting to PCB layout ..

Keep in mind that the coin cell will not work well in low voltage situations (ie below 1.8V + a bit) as REG0 might misbehave, hence the need for large capacitance on the coin cell (and some on VDD).

Edit: VDDH High voltage mode operating voltage 2.5 minimum, so coin cell (as seen at VDDH) must not dip below 2.5V