Advertising doesn't change name after code update

[Corapche]

Greetings,

I've been developing a DFU firmware that should update the device through Android. The thing is, the device works, but I changed the advertising name, and it still shows the old name when I try to update the device. I use the following function to update the name:

static void make_dev_name(void)
{
    ble_gap_addr_t device_address;
    uint8_t companyName[] = {"M"};
    uint8_t modelName[] = {"1"};
    uint8_t *macAddressName;
    uint8_t macTmp[12];

    sd_ble_gap_addr_get(&device_address);
    macAddressName = Convert_Hex_To_Ascii(&device_address.addr[0], 4);
    memcpy(&DEVICE_NAME[0], companyName, 1);
    memcpy(&DEVICE_NAME[1], modelName, 1);
    memcpy(&DEVICE_NAME[2], macAddressName, 12);

}

Any idea why this issue occurs?

I used reference from here;
https://novelbits.io/ota-device-firmware-update-part-3/

[Vidar Berg]

Hello,

When is make_dev_name() called, is it only on startup, or are you sending a command over BLE to update the name? 

Best regards,

Vidar

[Corapche]

Only on start-up.

int main(void)
{
    bool erase_bonds;
    ret_code_t err_code;
    ble_gap_addr_t device_address;
    
    // Comment this for new modules
    sd_power_dcdc_mode_set(1);

    // Initialize.
    uart_init();
    log_init();

    // Initialize the async SVCI interface to bootloader before any interrupts are enabled.
    err_code = ble_dfu_buttonless_async_svci_init();
    APP_ERROR_CHECK(err_code);

    timers_init();
    buttons_leds_init(&erase_bonds);
    power_management_init();
    ble_stack_init();

    make_dev_name();

    gap_params_init();
    gatt_init();
    services_init();
    advertising_init();
    conn_params_init();

    //if(nrf_gpio_pin_read(WAKEUP_IN_PIN))
    //{
    //    while(1);   // wait here 
    //}

    sd_ble_gap_addr_get(&device_address);
    nrf_delay_ms(5);
    while(!nrf_gpio_pin_read(WAKEUP_IN_PIN))
    {
        //nrf_gpio_pin_clear(UART_TX_NOTIFY);
        //nrf_delay_ms(250);
        //nrf_gpio_pin_set(UART_TX_NOTIFY);
        for(int i=0; i<6; i++)
        {
            do
            {
                err_code = app_uart_put(device_address.addr[i]);
                if ((err_code != NRF_SUCCESS) && (err_code != NRF_ERROR_BUSY))
                {
                    NRF_LOG_ERROR("Failed receiving NUS message. Error 0x%x. ", err_code);
                    APP_ERROR_CHECK(err_code);
                }
            } while (err_code == NRF_ERROR_BUSY);
            
        }
        //nrf_delay_ms(500);
        nrf_delay_ms(50);
    }

    // Start execution.
    //printf("\r\nApplication started.\r\n");
    NRF_LOG_INFO("Debug logging for UART over RTT started.");
    while(app_uart_tx_done());
    app_uart_close();
    advertising_start();

    wdt_init();

    // Enter main loop.
    for (;;)
    {
        // Feed the watchdog
        feed_dog();
        // Power management 
        idle_state_handle();

    }
}

[Vidar Berg]

Thanks for confirming. But I can't tell from the snippet you posted where DEVICE_NAME is referenced. Could you post your main.c file here?

[Corapche]

Device name is referenced as uint8_t array

/** @file
 *
 * @defgroup ble_sdk_uart_over_ble_main main.c
 * @{
 * @ingroup  ble_sdk_app_nus_eval
 * @brief    UART over BLE application main file.
 *
 * This file contains the source code for a sample application that uses the Nordic UART service.
 * This application uses the @ref srvlib_conn_params module.
 */


#include <stdint.h>
#include <string.h>
#include "main.h"
#include "nordic_common.h"
#include "nrf.h"
#include "ble_hci.h"
#include "ble_advdata.h"
#include "ble_advertising.h"
#include "ble_conn_params.h"
#include "nrf_sdh.h"
#include "nrf_sdh_soc.h"
#include "nrf_sdh_ble.h"
#include "nrf_ble_gatt.h"
#include "nrf_ble_qwr.h"
#include "app_timer.h"
#include "ble_nus.h"
#include "app_uart.h"
#include "app_util_platform.h"
#include "bsp_btn_ble.h"
#include "nrf_pwr_mgmt.h"

#if defined (UART_PRESENT)
#include "nrf_uart.h"
#endif
#if defined (UARTE_PRESENT)
#include "nrf_uarte.h"
#endif

#include "nrf_log.h"
#include "nrf_log_ctrl.h"
#include "nrf_log_default_backends.h"
#include "nrf_gpio.h"
#include "nrf_delay.h"  
#include "nrf_drv_wdt.h"
#include "nrf_drv_clock.h"

// BEGIN Block Added for DFU
#include "nrf_power.h"
#include "nrf_dfu_ble_svci_bond_sharing.h"
#include "nrf_svci_async_function.h"
#include "nrf_svci_async_handler.h"
#include "ble_dfu.h"
#include "nrf_bootloader_info.h"
// END Block Added for DFU


#define WAKEUP_IN_PIN   NRF_GPIO_PIN_MAP(0,4)               // Check this pin if need to send MAC
static void uart_init(void);


#define APP_BLE_CONN_CFG_TAG            1                                           /**< A tag identifying the SoftDevice BLE configuration. */

uint8_t DEVICE_NAME[29];
//#define DEVICE_NAME                     "M1"                                   /**< Name of device. Will be included in the advertising data. */
#define NUS_SERVICE_UUID_TYPE           BLE_UUID_TYPE_VENDOR_BEGIN                  /**< UUID type for the Nordic UART Service (vendor specific). */

#define APP_BLE_OBSERVER_PRIO           3                                           /**< Application's BLE observer priority. You shouldn't need to modify this value. */

#define APP_ADV_INTERVAL                MSEC_TO_UNITS(500, UNIT_0_625_MS)            /**< The advertising interval (in units of 0.625 ms. This value corresponds to 40 ms). */

#define APP_ADV_DURATION                BLE_GAP_ADV_TIMEOUT_GENERAL_UNLIMITED       /**< The advertising duration (180 seconds) in units of 10 milliseconds. */

#define MIN_CONN_INTERVAL               MSEC_TO_UNITS(20, UNIT_1_25_MS)             /**< Minimum acceptable connection interval (20 ms), Connection interval uses 1.25 ms units. */
#define MAX_CONN_INTERVAL               MSEC_TO_UNITS(75, UNIT_1_25_MS)             /**< Maximum acceptable connection interval (75 ms), Connection interval uses 1.25 ms units. */
#define SLAVE_LATENCY                   0                                           /**< Slave latency. */
#define CONN_SUP_TIMEOUT                MSEC_TO_UNITS(4000, UNIT_10_MS)             /**< Connection supervisory timeout (4 seconds), Supervision Timeout uses 10 ms units. */
#define FIRST_CONN_PARAMS_UPDATE_DELAY  APP_TIMER_TICKS(5000)                       /**< Time from initiating event (connect or start of notification) to first time sd_ble_gap_conn_param_update is called (5 seconds). */
#define NEXT_CONN_PARAMS_UPDATE_DELAY   APP_TIMER_TICKS(30000)                      /**< Time between each call to sd_ble_gap_conn_param_update after the first call (30 seconds). */
#define MAX_CONN_PARAMS_UPDATE_COUNT    3                                           /**< Number of attempts before giving up the connection parameter negotiation. */

#define DEAD_BEEF                       0xDEADBEEF                                  /**< Value used as error code on stack dump, can be used to identify stack location on stack unwind. */

#define UART_TX_BUF_SIZE                256                                         /**< UART TX buffer size. */
#define UART_RX_BUF_SIZE                256                                         /**< UART RX buffer size. */


BLE_NUS_DEF(m_nus, NRF_SDH_BLE_TOTAL_LINK_COUNT);                                   /**< BLE NUS service instance. */
NRF_BLE_GATT_DEF(m_gatt);                                                           /**< GATT module instance. */
NRF_BLE_QWR_DEF(m_qwr);                                                             /**< Context for the Queued Write module.*/
BLE_ADVERTISING_DEF(m_advertising);                                                 /**< Advertising module instance. */
APP_TIMER_DEF(m_inactivity_timer_id);                                               // Define the timer instance


static uint16_t   m_conn_handle          = BLE_CONN_HANDLE_INVALID;                 /**< Handle of the current connection. */
static uint16_t   m_ble_nus_max_data_len = BLE_GATT_ATT_MTU_DEFAULT - 3;            /**< Maximum length of data (in bytes) that can be transmitted to the peer by the Nordic UART service module. */
static ble_uuid_t m_adv_uuids[]          =                                          /**< Universally unique service identifier. */
{
    {BLE_UUID_NUS_SERVICE, NUS_SERVICE_UUID_TYPE}
};

//*************** DFU START     *********************************************


/**@brief Handler for shutdown preparation.
 *
 * @details During shutdown procedures, this function will be called at a 1 second interval
 *          untill the function returns true. When the function returns true, it means that the
 *          app is ready to reset to DFU mode.
 *
 * @param[in]   event   Power manager event.
 *
 * @retval  True if shutdown is allowed by this power manager handler, otherwise false.
 */
static bool app_shutdown_handler(nrf_pwr_mgmt_evt_t event)
{
    switch (event)
    {
        case NRF_PWR_MGMT_EVT_PREPARE_DFU:
            NRF_LOG_INFO("Power management wants to reset to DFU mode.");
            // YOUR_JOB: Get ready to reset into DFU mode
            //
            // If you aren't finished with any ongoing tasks, return "false" to
            // signal to the system that reset is impossible at this stage.
            //
            // Here is an example using a variable to delay resetting the device.
            //
            // if (!m_ready_for_reset)
            // {
            //      return false;
            // }
            // else
            //{
            //
            //    // Device ready to enter
            //    uint32_t err_code;
            //    err_code = sd_softdevice_disable();
            //    APP_ERROR_CHECK(err_code);
            //    err_code = app_timer_stop_all();
            //    APP_ERROR_CHECK(err_code);
            //}
            break;

        default:
            // YOUR_JOB: Implement any of the other events available from the power management module:
            //      -NRF_PWR_MGMT_EVT_PREPARE_SYSOFF
            //      -NRF_PWR_MGMT_EVT_PREPARE_WAKEUP
            //      -NRF_PWR_MGMT_EVT_PREPARE_RESET
            return true;
    }

    NRF_LOG_INFO("Power management allowed to reset to DFU mode.");
    return true;
}

//lint -esym(528, m_app_shutdown_handler)
/**@brief Register application shutdown handler with priority 0.
 */
NRF_PWR_MGMT_HANDLER_REGISTER(app_shutdown_handler, 0);


static void buttonless_dfu_sdh_state_observer(nrf_sdh_state_evt_t state, void * p_context)
{
    if (state == NRF_SDH_EVT_STATE_DISABLED)
    {
        // Softdevice was disabled before going into reset. Inform bootloader to skip CRC on next boot.
        nrf_power_gpregret2_set(BOOTLOADER_DFU_SKIP_CRC);

        //Go to system off.
        nrf_pwr_mgmt_shutdown(NRF_PWR_MGMT_SHUTDOWN_GOTO_SYSOFF);
    }
}

/* nrf_sdh state observer. */
NRF_SDH_STATE_OBSERVER(m_buttonless_dfu_state_obs, 0) =
{
    .handler = buttonless_dfu_sdh_state_observer,
};


static void advertising_config_get(ble_adv_modes_config_t * p_config)
{
    memset(p_config, 0, sizeof(ble_adv_modes_config_t));

    p_config->ble_adv_fast_enabled  = true;
    p_config->ble_adv_fast_interval = APP_ADV_INTERVAL;
    p_config->ble_adv_fast_timeout  = APP_ADV_DURATION;
}

static void disconnect(uint16_t conn_handle, void * p_context)
{
    UNUSED_PARAMETER(p_context);

    ret_code_t err_code = sd_ble_gap_disconnect(conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
    if (err_code != NRF_SUCCESS)
    {
        NRF_LOG_WARNING("Failed to disconnect connection. Connection handle: %d Error: %d", conn_handle, err_code);
    }
    else
    {
        NRF_LOG_DEBUG("Disconnected connection handle %d", conn_handle);
    }
}

// YOUR_JOB: Update this code if you want to do anything given a DFU event (optional).
/**@brief Function for handling dfu events from the Buttonless Secure DFU service
 *
 * @param[in]   event   Event from the Buttonless Secure DFU service.
 */
static void ble_dfu_evt_handler(ble_dfu_buttonless_evt_type_t event)
{
    switch (event)
    {
        case BLE_DFU_EVT_BOOTLOADER_ENTER_PREPARE:
        {
            NRF_LOG_INFO("Device is preparing to enter bootloader mode.");

            // Prevent device from advertising on disconnect.
            ble_adv_modes_config_t config;
            advertising_config_get(&config);
            config.ble_adv_on_disconnect_disabled = true;
            ble_advertising_modes_config_set(&m_advertising, &config);

            // Disconnect all other bonded devices that currently are connected.
            // This is required to receive a service changed indication
            // on bootup after a successful (or aborted) Device Firmware Update.
            uint32_t conn_count = ble_conn_state_for_each_connected(disconnect, NULL);
            NRF_LOG_INFO("Disconnected %d links.", conn_count);
            break;
        }

        case BLE_DFU_EVT_BOOTLOADER_ENTER:
            // YOUR_JOB: Write app-specific unwritten data to FLASH, control finalization of this
            //           by delaying reset by reporting false in app_shutdown_handler
            NRF_LOG_INFO("Device will enter bootloader mode.");
            break;

        case BLE_DFU_EVT_BOOTLOADER_ENTER_FAILED:
            NRF_LOG_ERROR("Request to enter bootloader mode failed asynchroneously.");
            // YOUR_JOB: Take corrective measures to resolve the issue
            //           like calling APP_ERROR_CHECK to reset the device.
            break;

        case BLE_DFU_EVT_RESPONSE_SEND_ERROR:
            NRF_LOG_ERROR("Request to send a response to client failed.");
            // YOUR_JOB: Take corrective measures to resolve the issue
            //           like calling APP_ERROR_CHECK to reset the device.
            APP_ERROR_CHECK(false);
            break;

        default:
            NRF_LOG_ERROR("Unknown event from ble_dfu_buttonless.");
            break;
    }
}

//*************** DFU END       **********************************************

// Watch Dog enable
nrfx_wdt_channel_id m_channel_id;

void wdt_event_handler(void)
{
    NRF_LOG_INFO("%s", __func__);
    while (NRF_LOG_PROCESS());
    NRF_LOG_FINAL_FLUSH();
}

void feed_dog(void)
{
     nrf_drv_wdt_channel_feed(m_channel_id);
}

void wdt_init(void)
{
    //2 sec timeout
    uint32_t err_code = NRF_SUCCESS;
    nrfx_wdt_config_t wdt_config = NRFX_WDT_DEAFULT_CONFIG;

    err_code = nrfx_wdt_init(&wdt_config, wdt_event_handler);
    APP_ERROR_CHECK(err_code);

    err_code = nrfx_wdt_channel_alloc(&m_channel_id);
    APP_ERROR_CHECK(err_code);

    nrfx_wdt_enable();

}

// Inactivity timeout handler
static void inactivity_timeout_handler(void * p_context)
{
    UNUSED_PARAMETER(p_context);
    if (m_conn_handle != BLE_CONN_HANDLE_INVALID)
    {
        // Disconnect from the peer.
        ret_code_t err_code = sd_ble_gap_disconnect(m_conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
        APP_ERROR_CHECK(err_code);
    }
}


/**@brief Function for assert macro callback.
 *
 * @details This function will be called in case of an assert in the SoftDevice.
 *
 * @warning This handler is an example only and does not fit a final product. You need to analyse
 *          how your product is supposed to react in case of Assert.
 * @warning On assert from the SoftDevice, the system can only recover on reset.
 *
 * @param[in] line_num    Line number of the failing ASSERT call.
 * @param[in] p_file_name File name of the failing ASSERT call.
 */
void assert_nrf_callback(uint16_t line_num, const uint8_t * p_file_name)
{
    app_error_handler(DEAD_BEEF, line_num, p_file_name);
}

/**@brief Function for initializing the timer module.
 */
static void timers_init(void)
{
    ret_code_t err_code = app_timer_init();
    APP_ERROR_CHECK(err_code);

    // Create timer
    err_code = app_timer_create(&m_inactivity_timer_id,
                                APP_TIMER_MODE_SINGLE_SHOT,
                                inactivity_timeout_handler);
    APP_ERROR_CHECK(err_code);
}

/**@brief Function for the GAP initialization.
 *
 * @details This function will set up all the necessary GAP (Generic Access Profile) parameters of
 *          the device. It also sets the permissions and appearance.
 */
static void gap_params_init(void)
{
    uint32_t                err_code;
    ble_gap_conn_params_t   gap_conn_params;
    ble_gap_conn_sec_mode_t sec_mode;

    BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode);

    err_code = sd_ble_gap_device_name_set(&sec_mode,
                                          (const uint8_t *) DEVICE_NAME,
                                          strlen(DEVICE_NAME));
    APP_ERROR_CHECK(err_code);

    err_code = sd_ble_gap_appearance_set(BLE_APPEARANCE_UNKNOWN);
    APP_ERROR_CHECK(err_code);

    memset(&gap_conn_params, 0, sizeof(gap_conn_params));

    gap_conn_params.min_conn_interval = MIN_CONN_INTERVAL;
    gap_conn_params.max_conn_interval = MAX_CONN_INTERVAL;
    gap_conn_params.slave_latency     = SLAVE_LATENCY;
    gap_conn_params.conn_sup_timeout  = CONN_SUP_TIMEOUT;

    err_code = sd_ble_gap_ppcp_set(&gap_conn_params);
    APP_ERROR_CHECK(err_code);
}


/**@brief Function for handling Queued Write Module errors.
 *
 * @details A pointer to this function will be passed to each service which may need to inform the
 *          application about an error.
 *
 * @param[in]   nrf_error   Error code containing information about what went wrong.
 */
static void nrf_qwr_error_handler(uint32_t nrf_error)
{
    APP_ERROR_HANDLER(nrf_error);
}


/**@brief Function for handling the data from the Nordic UART Service.
 *
 * @details This function will process the data received from the Nordic UART BLE Service and send
 *          it to the UART module.
 *
 * @param[in] p_evt       Nordic UART Service event.
 */
/**@snippet [Handling the data received over BLE] */
static void nus_data_handler(ble_nus_evt_t * p_evt)
{

    if (p_evt->type == BLE_NUS_EVT_RX_DATA)
    {
        uint32_t err_code;
        // Notify the MCU that you will send data on UART
        nrf_gpio_pin_clear(UART_TX_NOTIFY);
        nrf_delay_ms(5);
        nrf_gpio_pin_set(UART_TX_NOTIFY);
        nrf_delay_ms(10);

        NRF_LOG_DEBUG("Received data from BLE NUS. Writing data on UART.");
        NRF_LOG_HEXDUMP_DEBUG(p_evt->params.rx_data.p_data, p_evt->params.rx_data.length);
        
        // Restart the inactivity timer
        err_code = app_timer_start(m_inactivity_timer_id, APP_TIMER_TICKS(13000), NULL);    // 13 sec timeout
        APP_ERROR_CHECK(err_code);

        for (uint32_t i = 0; i < p_evt->params.rx_data.length; i++)
        {
            do
            {
                err_code = app_uart_put(p_evt->params.rx_data.p_data[i]);
                if ((err_code != NRF_SUCCESS) && (err_code != NRF_ERROR_BUSY))
                {
                    NRF_LOG_ERROR("Failed receiving NUS message. Error 0x%x. ", err_code);
                    APP_ERROR_CHECK(err_code);
                }
            } while (err_code == NRF_ERROR_BUSY);
        }

        if (p_evt->params.rx_data.p_data[p_evt->params.rx_data.length - 1] == '\r')
        {
            while (app_uart_put('\n') == NRF_ERROR_BUSY);
        }

    }

}
/**@snippet [Handling the data received over BLE] */


/**@brief Function for initializing services that will be used by the application.
 */
static void services_init(void)
{
    uint32_t           err_code;
    ble_nus_init_t     nus_init;
    nrf_ble_qwr_init_t qwr_init = {0};
    ble_dfu_buttonless_init_t dfus_init = {0};

    // Initialize Queued Write Module.
    qwr_init.error_handler = nrf_qwr_error_handler;

    err_code = nrf_ble_qwr_init(&m_qwr, &qwr_init);
    APP_ERROR_CHECK(err_code);

    // Initialize NUS.
    memset(&nus_init, 0, sizeof(nus_init));

    nus_init.data_handler = nus_data_handler;

    err_code = ble_nus_init(&m_nus, &nus_init);
    APP_ERROR_CHECK(err_code);

    // Initialize DFU buttonless.
    dfus_init.evt_handler = ble_dfu_evt_handler;

    err_code = ble_dfu_buttonless_init(&dfus_init);
    APP_ERROR_CHECK(err_code);
}


/**@brief Function for handling an event from the Connection Parameters Module.
 *
 * @details This function will be called for all events in the Connection Parameters Module
 *          which are passed to the application.
 *
 * @note All this function does is to disconnect. This could have been done by simply setting
 *       the disconnect_on_fail config parameter, but instead we use the event handler
 *       mechanism to demonstrate its use.
 *
 * @param[in] p_evt  Event received from the Connection Parameters Module.
 */
static void on_conn_params_evt(ble_conn_params_evt_t * p_evt)
{
    uint32_t err_code;

    if (p_evt->evt_type == BLE_CONN_PARAMS_EVT_FAILED)
    {
        err_code = sd_ble_gap_disconnect(m_conn_handle, BLE_HCI_CONN_INTERVAL_UNACCEPTABLE);
        APP_ERROR_CHECK(err_code);
    }
}


/**@brief Function for handling errors from the Connection Parameters module.
 *
 * @param[in] nrf_error  Error code containing information about what went wrong.
 */
static void conn_params_error_handler(uint32_t nrf_error)
{
    APP_ERROR_HANDLER(nrf_error);
}


/**@brief Function for initializing the Connection Parameters module.
 */
static void conn_params_init(void)
{
    uint32_t               err_code;
    ble_conn_params_init_t cp_init;

    memset(&cp_init, 0, sizeof(cp_init));

    cp_init.p_conn_params                  = NULL;
    cp_init.first_conn_params_update_delay = FIRST_CONN_PARAMS_UPDATE_DELAY;
    cp_init.next_conn_params_update_delay  = NEXT_CONN_PARAMS_UPDATE_DELAY;
    cp_init.max_conn_params_update_count   = MAX_CONN_PARAMS_UPDATE_COUNT;
    cp_init.start_on_notify_cccd_handle    = BLE_GATT_HANDLE_INVALID;
    cp_init.disconnect_on_fail             = false;
    cp_init.evt_handler                    = on_conn_params_evt;
    cp_init.error_handler                  = conn_params_error_handler;

    err_code = ble_conn_params_init(&cp_init);
    APP_ERROR_CHECK(err_code);
}


/**@brief Function for putting the chip into sleep mode.
 *
 * @note This function will not return.
 */
static void sleep_mode_enter(void)
{
    uint32_t err_code = bsp_indication_set(BSP_INDICATE_IDLE);
    APP_ERROR_CHECK(err_code);

    // Prepare wakeup buttons.
    //err_code = bsp_btn_ble_sleep_mode_prepare();
    //APP_ERROR_CHECK(err_code);

    // Go to system-off mode (this function will not return; wakeup will cause a reset).
    err_code = sd_power_system_off();
    APP_ERROR_CHECK(err_code);
}


/**@brief Function for handling advertising events.
 *
 * @details This function will be called for advertising events which are passed to the application.
 *
 * @param[in] ble_adv_evt  Advertising event.
 */
static void on_adv_evt(ble_adv_evt_t ble_adv_evt)
{
    uint32_t err_code;

    switch (ble_adv_evt)
    {
        case BLE_ADV_EVT_FAST:
            err_code = bsp_indication_set(BSP_INDICATE_ADVERTISING);
            APP_ERROR_CHECK(err_code);
            break;
        case BLE_ADV_EVT_IDLE:
            sleep_mode_enter();
            break;
        default:
            break;
    }
}


/**@brief Function for handling BLE events.
 *
 * @param[in]   p_ble_evt   Bluetooth stack event.
 * @param[in]   p_context   Unused.
 */
static void ble_evt_handler(ble_evt_t const * p_ble_evt, void * p_context)
{
    uint32_t err_code;

    switch (p_ble_evt->header.evt_id)
    {
        case BLE_GAP_EVT_CONNECTED:
            uart_init();
            NRF_LOG_INFO("Connected");
            //err_code = bsp_indication_set(BSP_INDICATE_CONNECTED);
            //APP_ERROR_CHECK(err_code);
            m_conn_handle = p_ble_evt->evt.gap_evt.conn_handle;
            err_code = nrf_ble_qwr_conn_handle_assign(&m_qwr, m_conn_handle);
            APP_ERROR_CHECK(err_code);
            // Start the inactivity timer
            err_code = app_timer_start(m_inactivity_timer_id, APP_TIMER_TICKS(13000), NULL);
            APP_ERROR_CHECK(err_code);
            break;

        case BLE_GAP_EVT_DISCONNECTED:
            // Stop the inactivity timer
            err_code = app_timer_stop(m_inactivity_timer_id);
            APP_ERROR_CHECK(err_code);
            // Wait for UART to finish
            while(app_uart_tx_done());
            app_uart_close();
            NRF_LOG_INFO("Disconnected");
            // LED indication will be changed when advertising starts.
            m_conn_handle = BLE_CONN_HANDLE_INVALID;
            break;

        case BLE_GAP_EVT_PHY_UPDATE_REQUEST:
        {
            NRF_LOG_DEBUG("PHY update request.");
            ble_gap_phys_t const phys =
            {
                .rx_phys = BLE_GAP_PHY_AUTO,
                .tx_phys = BLE_GAP_PHY_AUTO,
            };
            err_code = sd_ble_gap_phy_update(p_ble_evt->evt.gap_evt.conn_handle, &phys);
            APP_ERROR_CHECK(err_code);
        } break;

        case BLE_GAP_EVT_SEC_PARAMS_REQUEST:
            // Pairing not supported
            err_code = sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_PAIRING_NOT_SUPP, NULL, NULL);
            APP_ERROR_CHECK(err_code);
            break;

        case BLE_GATTS_EVT_SYS_ATTR_MISSING:
            // No system attributes have been stored.
            err_code = sd_ble_gatts_sys_attr_set(m_conn_handle, NULL, 0, 0);
            APP_ERROR_CHECK(err_code);
            break;

        case BLE_GATTC_EVT_TIMEOUT:
            // Stop the inactivity timer
            err_code = app_timer_stop(m_inactivity_timer_id);
            APP_ERROR_CHECK(err_code);
            // Disconnect on GATT Client timeout event.
            err_code = sd_ble_gap_disconnect(p_ble_evt->evt.gattc_evt.conn_handle,
                                             BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
            APP_ERROR_CHECK(err_code);
            break;

        case BLE_GATTS_EVT_TIMEOUT:
            // Stop the inactivity timer
            err_code = app_timer_stop(m_inactivity_timer_id);
            APP_ERROR_CHECK(err_code);
            // Disconnect on GATT Server timeout event.
            err_code = sd_ble_gap_disconnect(p_ble_evt->evt.gatts_evt.conn_handle,
                                             BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
            APP_ERROR_CHECK(err_code);
            break;

        default:
            // No implementation needed.
            break;
    }
}


/**@brief Function for the SoftDevice initialization.
 *
 * @details This function initializes the SoftDevice and the BLE event interrupt.
 */
static void ble_stack_init(void)
{
    ret_code_t err_code;

    err_code = nrf_sdh_enable_request();
    APP_ERROR_CHECK(err_code);

    // Configure the BLE stack using the default settings.
    // Fetch the start address of the application RAM.
    uint32_t ram_start = 0;
    err_code = nrf_sdh_ble_default_cfg_set(APP_BLE_CONN_CFG_TAG, &ram_start);
    APP_ERROR_CHECK(err_code);

    // Enable BLE stack.
    err_code = nrf_sdh_ble_enable(&ram_start);
    APP_ERROR_CHECK(err_code);

    // Register a handler for BLE events.
    NRF_SDH_BLE_OBSERVER(m_ble_observer, APP_BLE_OBSERVER_PRIO, ble_evt_handler, NULL);
}


/**@brief Function for handling events from the GATT library. */
void gatt_evt_handler(nrf_ble_gatt_t * p_gatt, nrf_ble_gatt_evt_t const * p_evt)
{
    if ((m_conn_handle == p_evt->conn_handle) && (p_evt->evt_id == NRF_BLE_GATT_EVT_ATT_MTU_UPDATED))
    {
        m_ble_nus_max_data_len = p_evt->params.att_mtu_effective - OPCODE_LENGTH - HANDLE_LENGTH;
        NRF_LOG_INFO("Data len is set to 0x%X(%d)", m_ble_nus_max_data_len, m_ble_nus_max_data_len);
    }
    NRF_LOG_DEBUG("ATT MTU exchange completed. central 0x%x peripheral 0x%x",
                  p_gatt->att_mtu_desired_central,
                  p_gatt->att_mtu_desired_periph);
}


/**@brief Function for initializing the GATT library. */
void gatt_init(void)
{
    ret_code_t err_code;

    err_code = nrf_ble_gatt_init(&m_gatt, gatt_evt_handler);
    APP_ERROR_CHECK(err_code);

    err_code = nrf_ble_gatt_att_mtu_periph_set(&m_gatt, NRF_SDH_BLE_GATT_MAX_MTU_SIZE);
    APP_ERROR_CHECK(err_code);
}


/**@brief Function for handling events from the BSP module.
 *
 * @param[in]   event   Event generated by button press.
 */
void bsp_event_handler(bsp_event_t event)
{
    uint32_t err_code;
    switch (event)
    {
        case BSP_EVENT_SLEEP:
            sleep_mode_enter();
            break;

        case BSP_EVENT_DISCONNECT:
            err_code = sd_ble_gap_disconnect(m_conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
            if (err_code != NRF_ERROR_INVALID_STATE)
            {
                APP_ERROR_CHECK(err_code);
            }
            break;

        case BSP_EVENT_WHITELIST_OFF:
            if (m_conn_handle == BLE_CONN_HANDLE_INVALID)
            {
                err_code = ble_advertising_restart_without_whitelist(&m_advertising);
                if (err_code != NRF_ERROR_INVALID_STATE)
                {
                    APP_ERROR_CHECK(err_code);
                }
            }
            break;

        default:
            break;
    }
}


/**@brief   Function for handling app_uart events.
 *
 * @details This function will receive a single character from the app_uart module and append it to
 *          a string. The string will be be sent over BLE when the last character received was a
 *          'new line' '\n' (hex 0x0A) or if the string has reached the maximum data length.
 */
/**@snippet [Handling the data received over UART] */
void uart_event_handle(app_uart_evt_t * p_event)
{
    static uint8_t data_array[BLE_NUS_MAX_DATA_LEN];
    static uint8_t index = 0;
    uint32_t       err_code;
    static uint8_t bytesToSend = 0;

    switch (p_event->evt_type)
    {
        case APP_UART_DATA_READY:
            UNUSED_VARIABLE(app_uart_get(&data_array[index]));

            if(index == 1)
            {
                bytesToSend = (char)data_array[index];
                bytesToSend+=2;
                //printf("%c", bytesToSend);
            }
            index++;

            if ((index >= bytesToSend)&&(index > 1))
            {

                //NRF_LOG_DEBUG("Ready to send data over BLE NUS");
                //NRF_LOG_HEXDUMP_DEBUG(data_array, index);
                
                do
                {
                    uint16_t length = (uint16_t)bytesToSend;
                    err_code = ble_nus_data_send(&m_nus, data_array, &length, m_conn_handle);
                    if ((err_code != NRF_ERROR_INVALID_STATE) &&
                        (err_code != NRF_ERROR_RESOURCES) &&
                        (err_code != NRF_ERROR_NOT_FOUND))
                    {
                        APP_ERROR_CHECK(err_code);
                    }
                } while (err_code == NRF_ERROR_RESOURCES);
              
                // Disconnect from phone
                if(data_array[2] != 0x01)
                {
                    // Stop the inactivity timer
                    ret_code_t err_code = app_timer_stop(m_inactivity_timer_id);
                    APP_ERROR_CHECK(err_code);

                    err_code = sd_ble_gap_disconnect(m_conn_handle, BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION);
                    APP_ERROR_CHECK(err_code);
                }

                index = 0;
                bytesToSend = 0;
            }

        //**************    ORG      ********************************************
            //UNUSED_VARIABLE(app_uart_get(&data_array[index]));
            //index++;

            //if (((data_array[index - 2] == '\n') &&
            //    (data_array[index - 1] == '\r')) ||
            //    (index >= m_ble_nus_max_data_len))
            //{
            //    if (index > 1)
            //    {
            //        NRF_LOG_DEBUG("Ready to send data over BLE NUS");
            //        NRF_LOG_HEXDUMP_DEBUG(data_array, index);
                    
            //        do
            //        {
            //            uint16_t length = (uint16_t)index;
            //            err_code = ble_nus_data_send(&m_nus, data_array, &length, m_conn_handle);
            //            if ((err_code != NRF_ERROR_INVALID_STATE) &&
            //                (err_code != NRF_ERROR_RESOURCES) &&
            //                (err_code != NRF_ERROR_NOT_FOUND))
            //            {
            //                APP_ERROR_CHECK(err_code);
            //            }
            //        } while (err_code == NRF_ERROR_RESOURCES);
            //    }
                
            //    index = 0;
            //}
            break;

        case APP_UART_COMMUNICATION_ERROR:
            APP_ERROR_HANDLER(p_event->data.error_communication);
            break;

        case APP_UART_FIFO_ERROR:
            APP_ERROR_HANDLER(p_event->data.error_code);
            break;

        default:
            break;
    }
}
/**@snippet [Handling the data received over UART] */


/**@brief  Function for initializing the UART module.
 */
/**@snippet [UART Initialization] */
static void uart_init(void)
{
    uint32_t                     err_code;
    app_uart_comm_params_t const comm_params =
    {
        .rx_pin_no    = RX_PIN_NUMBER,
        .tx_pin_no    = TX_PIN_NUMBER,
        .rts_pin_no   = RTS_PIN_NUMBER,
        .cts_pin_no   = CTS_PIN_NUMBER,
        .flow_control = APP_UART_FLOW_CONTROL_DISABLED,
        .use_parity   = false,
        .baud_rate    = NRF_UART_BAUDRATE_115200
    };

    APP_UART_FIFO_INIT(&comm_params,
                       UART_RX_BUF_SIZE,
                       UART_TX_BUF_SIZE,
                       uart_event_handle,
                       APP_IRQ_PRIORITY_LOW,
                       err_code);
    APP_ERROR_CHECK(err_code);
}
/**@snippet [UART Initialization] */


/**@brief Function for initializing the Advertising functionality.
 */
static void advertising_init(void)
{
    uint32_t               err_code;
    ble_advertising_init_t init;

    memset(&init, 0, sizeof(init));

    init.advdata.name_type          = BLE_ADVDATA_FULL_NAME;
    init.advdata.include_appearance = false;
    init.advdata.flags              = BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;

    init.srdata.uuids_complete.uuid_cnt = sizeof(m_adv_uuids) / sizeof(m_adv_uuids[0]);
    init.srdata.uuids_complete.p_uuids  = m_adv_uuids;

    init.config.ble_adv_fast_enabled  = true;
    init.config.ble_adv_fast_interval = APP_ADV_INTERVAL;
    init.config.ble_adv_fast_timeout  = APP_ADV_DURATION;
    init.evt_handler = on_adv_evt;

    err_code = ble_advertising_init(&m_advertising, &init);
    APP_ERROR_CHECK(err_code);

    ble_advertising_conn_cfg_tag_set(&m_advertising, APP_BLE_CONN_CFG_TAG);
}


/**@brief Function for initializing buttons and leds.
 *
 * @param[out] p_erase_bonds  Will be true if the clear bonding button was pressed to wake the application up.
 */
static void buttons_leds_init(bool * p_erase_bonds)
{
    bsp_event_t startup_event;

    //uint32_t err_code = bsp_init(BSP_INIT_LEDS | BSP_INIT_BUTTONS, bsp_event_handler);
    //uint32_t err_code = bsp_init(BSP_INIT_LEDS, bsp_event_handler);
    //APP_ERROR_CHECK(err_code);

    //err_code = bsp_btn_ble_init(NULL, &startup_event);
    //APP_ERROR_CHECK(err_code);

    //*p_erase_bonds = (startup_event == BSP_EVENT_CLEAR_BONDING_DATA);

    // Initialize output pin to notify the MCU
    nrf_gpio_cfg_output(UART_TX_NOTIFY);
    nrf_gpio_pin_set(UART_TX_NOTIFY);
    
    // Initialize pin to send MAC address
    nrf_gpio_cfg_input(WAKEUP_IN_PIN, NRF_GPIO_PIN_PULLUP);
}


/**@brief Function for initializing the nrf log module.
 */
static void log_init(void)
{
    ret_code_t err_code = NRF_LOG_INIT(NULL);
    APP_ERROR_CHECK(err_code);

    NRF_LOG_DEFAULT_BACKENDS_INIT();
}


/**@brief Function for initializing power management.
 */
static void power_management_init(void)
{
    ret_code_t err_code;
    err_code = nrf_pwr_mgmt_init();
    APP_ERROR_CHECK(err_code);
}


/**@brief Function for handling the idle state (main loop).
 *
 * @details If there is no pending log operation, then sleep until next the next event occurs.
 */
static void idle_state_handle(void)
{
    if (NRF_LOG_PROCESS() == false)
    {
        nrf_pwr_mgmt_run();
    }
}


/**@brief Function for starting advertising.
 */
static void advertising_start(void)
{
    uint32_t err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST);
    APP_ERROR_CHECK(err_code);
}


static uint8_t *Convert_Hex_To_Ascii(uint8_t *hex_data, uint16_t data_len)
{
    int i = 0;
    uint16_t j = 0;
    static uint8_t ascii_data[8];
    uint8_t pom_low, pom_high;

    for (i=0; i<data_len; i++)
    {
        pom_low = (hex_data[i] & 0x0F);
        pom_high = ((hex_data[i]>>4) & 0x0F);

        if((pom_low >= 0) && (pom_low <= 9))
        {
            pom_low += 0x30;
        }
        else
        {
            pom_low += 0x37;
        }

        if((pom_high >= 0) && (pom_high <= 9))
        {
            pom_high += 0x30;
        }
        else
        {
            pom_high += 0x37;
        }

        ascii_data[j++] = pom_high;
        ascii_data[j++] = pom_low;
    }

    return ascii_data; // return the address of the first element
}

static void make_dev_name(void)
{
    ble_gap_addr_t device_address;
    uint8_t companyName[] = {"M"};
    uint8_t modelName[] = {"1"}
    uint8_t *macAddressName;
    uint8_t macTmp[12];

    sd_ble_gap_addr_get(&device_address);
    macAddressName = Convert_Hex_To_Ascii(&device_address.addr[0], 4);
    
    memcpy(&DEVICE_NAME[0], companyName, 1);
    memcpy(&DEVICE_NAME[1], modelName, 1);
    memcpy(&DEVICE_NAME[2], macAddressName, 12);

}


/**@brief Application main function.
 */
int main(void)
{
    bool erase_bonds;
    ret_code_t err_code;
    ble_gap_addr_t device_address;
    
    // Comment this for new modules
    sd_power_dcdc_mode_set(1);

    // Initialize.
    uart_init();
    log_init();

    // Initialize the async SVCI interface to bootloader before any interrupts are enabled.
    err_code = ble_dfu_buttonless_async_svci_init();
    APP_ERROR_CHECK(err_code);

    timers_init();
    buttons_leds_init(&erase_bonds);
    power_management_init();
    ble_stack_init();

    make_dev_name();

    gap_params_init();
    gatt_init();
    services_init();
    advertising_init();
    conn_params_init();

    //if(nrf_gpio_pin_read(WAKEUP_IN_PIN))
    //{
    //    while(1);   // wait here 
    //}

    sd_ble_gap_addr_get(&device_address);
    nrf_delay_ms(5);
    while(!nrf_gpio_pin_read(WAKEUP_IN_PIN))
    {
        //nrf_gpio_pin_clear(UART_TX_NOTIFY);
        //nrf_delay_ms(250);
        //nrf_gpio_pin_set(UART_TX_NOTIFY);
        for(int i=0; i<6; i++)
        {
            do
            {
                err_code = app_uart_put(device_address.addr[i]);
                if ((err_code != NRF_SUCCESS) && (err_code != NRF_ERROR_BUSY))
                {
                    NRF_LOG_ERROR("Failed receiving NUS message. Error 0x%x. ", err_code);
                    APP_ERROR_CHECK(err_code);
                }
            } while (err_code == NRF_ERROR_BUSY);
            
        }
        //nrf_delay_ms(500);
        nrf_delay_ms(50);
    }

    // Start execution.
    //printf("\r\nApplication started.\r\n");
    NRF_LOG_INFO("Debug logging for UART over RTT started.");
    while(app_uart_tx_done());
    app_uart_close();
    advertising_start();

    wdt_init();

    // Enter main loop.
    for (;;)
    {
        // Feed the watchdog
        feed_dog();
        // Power management 
        idle_state_handle();

    }
}

/**
 * @}
 */

[Vidar Berg]

Thanks for sharing the code. But I'm not seeing any obvious errors in this implementation. Does the device advertise with the expected name if you load the application FW with your debugger? Also, are you sure the previous device name has not been cached by your phone? 

[Corapche]

The device does not advertise with the expected name, it advertises with its' previous name e.g. M0...

We also tried with a different phone that has never been connected to the device, but it still shows the previous name.

[Vidar Berg]

Strange. I replaced the code in the ble_app_uart example in SDK 17.1.0 with your main.c file (also removed the buttonless DFU features) to attempt to reproduce the problem, but I see the full name:

Can you place a breakpoint at the idle_state_handle() and inspect the DEVICE_NAME array to see if it is initialized correctly?

[Corapche]

Unfortunately, I can't debug it because the initial setup wasn't made in Segger. Instead, I'm trying to see what UART is giving me. I will post what when I have some results.

[Vidar Berg]

It's possible to use other tools such as GDB or Segger Ozone to debug the app if the project was built without an IDE.

[Corapche]

I tried to debug it with Ozone, commented log_init() because it got stuck there and now it gets stuck or it crashes on 

ble_dfu_buttonless_async_svci_init(); (line 1041)