Adding demo bootloader for nrf54L15

[reichel]

I do step-by-step elements from https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-5-fota-over-bluetooth-low-energy/

Using LBS sample, NCS 3.1.0, toolchain 3.1.0 and finally  No configure step for 'mcuboot', as mention in sysbuild.conf have only this

SB_CONFIG_BOOTLOADER_MCUBOOT=y

in prj.conf

CONFIG_NCS_SAMPLES_DEFAULTS=y

CONFIG_BT=y

CONFIG_BT_PERIPHERAL=y

CONFIG_BT_DEVICE_NAME="Nordic_LBS"

# Enable the LBS service

CONFIG_BT_LBS=y

CONFIG_BT_LBS_POLL_BUTTON=y

CONFIG_DK_LIBRARY=y

CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=2048

CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU=y

Not sure what goes wrong (and feel that documentation changes too fast ... too many versions in a short time)

[reichel]

Not sure why I received  "Cannot upgrade: slots are not compatible",

both partitions have the  same size, only shrink and empty reallocated at the end

[reichel]

Wrong alignment now work's

 

but still would like to know about earlier questions.

[Amanda Hsieh]

(updated)

reichel said:

1) On L15 "have" magic from dtsi set to 0x165000 for maximum size of app if config was generated automatically. I see this number in zephyr\dts\vendor\nordic\nrf54l15.dtsi but for cpuflpr and my app is for configuration cpuapp (and PM manager do not allow me to build smaller region) For L05 I see in dts 0x75800 but If I create app without bootloader in partition.yml I've got 0x7d000 (so full 512). Could you explain ?

We set it do 500k by default as flpr is not supported on the l05 and l10 variant yet. https://github.com/nrfconnect/sdk-zephyr/blob/dc15a79bfeb842bfb503fd63017e8cb371050ddf/dts/vendor/nordic/nrf54l05_partition.dtsi#L7

https://github.com/nrfconnect/sdk-zephyr/blob/dc15a79bfeb842bfb503fd63017e8cb371050ddf/dts/vendor/nordic/nrf54l10_partition.dtsi#L7 

 

reichel said:

2) Now (without soft device) there is no common BT stack ? Because simple app is huge and have more than 220kb, so with dual bank, there is no possibility to use mcuboot (any option for single, like in older way ?) Without very hard optimization (maybe should go back to nrf52 ...). Is there any way to use a single bank ?

There’s no single‑bank BLE DFU in NCS. For BLE DFU, you need dual‑bank (two slots). Only the serial recovery mode supports the single bank. See https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-1-dfu-over-uart/ 

For the nRF54L05 BLE DFU, I suggest building the pm_static_nrf54l15dk_nrf54l05_cpuapp_release.yml to avoid slot allocation issues. 

[reichel]

so if set for flpr why is used for cpuapp during generation of partition.yml ?

Link to pm_static_nrf54l15dk_nrf54l05_cpuapp_release.yml gives 404, not sure should I log to , add repo , ?!

BTW. it is not a problem of calculating partition etc. This is normal day. But I feel that documentation and zephyr are a little bit underdeveloped. It supposedly "solves" a lot of issues, but if something doesn't work, you have to dig deeper (today I came across a library for the HDC2080 again, it supposedly exists, but only a little, and the rest needs to be added anyway... so maybe it would be easier to write it from scratch without all that overhead...)

[Amanda Hsieh]

No, it doesn't set as flpr is not supported for nRF54L05.

That's an internal link. Here is the content:

mcuboot:
  address: 0x0
  region: flash_primary
  size: 0x6000

mcuboot_primary:
  address: 0x6000
  orig_span: &id001
  - app
  - mcuboot_pad
  region: flash_primary
  size: 0x3a000
  span: *id001
mcuboot_pad:
  address: 0x6000
  region: flash_primary
  size: 0x800
app:
  address: 0x6800
  region: flash_primary
  size: 0x39800
mcuboot_primary_app:
  address: 0x6800
  orig_span: &id002
  - app
  region: flash_primary
  size: 0x39800
  span: *id002

mcuboot_secondary:
  address: 0x40000
  orig_span: &id003
  - mcuboot_secondary_pad
  - mcuboot_secondary_app
  region: flash_primary
  size: 0x3a000
  span: *id003
mcuboot_secondary_pad:
  address: 0x40000
  region: flash_primary
  size: 0x800
mcuboot_secondary_app:
  address: 0x40800
  region: flash_primary
  size: 0x39800

settings_storage:
  address: 0x7a000
  region: flash_primary
  size: 0x3000