6431.central_uart program from Vidar Berg with updates not working reliably in v3.1.1

[Burt]

We are using Vidar's program that is the basic samples/bluetooth/central_uart sample but with 3 board files so the program can be run on the nrf9160dk/nrf9160/ns board, in conjunction with bluetooth/samples/nci_lpuart running on the nRF52840 on the nRF9160DK board.

Depending upon when I reset the nrf9160, I frequently see the following, where I have added a few printk's to the code. I will show here the successful run followed by a failure. Please ignore the ECC key errors--they can be fixed with two extra config options. To make the error happen frequently, in pracitice I am push button resetting the nRF9160 soon after
Starting Bluetooth Central UART sample
Each time I see the "draining bytes from the uart" printk's that I added to bt_hci_transport_setup(), that's when the program times out and crashes.

*** Booting nRF Connect SDK v3.1.1-e2a97fe2578a ***
*** Using Zephyr OS v4.1.99-ff8f0c579eeb ***
[00:00:00.382,415] <err> bt_hci_core: HCI driver is not ready
[00:00:00.382,446] <err> central_uart: Bluetooth init failed (err -19)
*** Booting nRF Connect SDK v3.1.1-e2a97fe2578a ***
*** Using Zephyr OS v4.1.99-ff8f0c579eeb ***
[00:00:00.285,797] <err> bt_hci_core: HCI driver is not ready
[00:00:00.285,827] <err> central_uart: Bluetooth init failed (err -19)
*** Booting nRF Connect SDK v3.1.1-e2a97fe2578a ***
*** Using Zephyr OS v4.1.99-ff8f0c579eeb ***
[00:00:00.286,865] <err> bt_hci_core: HCI driver is not ready
[00:00:00.286,895] <err> central_uart: Bluetooth init failed (err -19)
*** Booting nRF Connect SDK v3.1.1-e2a97fe2578a ***
*** Using Zephyr OS v4.1.99-ff8f0c579eeb ***
[00:00:00.479,858] <inf> fs_nvs: 2 Sectors of 4096 bytes
[00:00:00.479,858] <inf> fs_nvs: alloc wra: 0, fe8
[00:00:00.479,888] <inf> fs_nvs: data wra: 0, 0
h4_open() entered...
bt_hci_transport_setup() entered...
bt_hci_transport_setup() about to gpio_pin_set(port, RESET_GPIO_PIN=24, 0)
bt_hci_transport_setup() exit success
h4_open() exit
bt_init() entered...
hci_init() entered...
common_init() entered...
common_init() about to  BT_HCI_OP_RESET
[00:00:01.192,993] <err> bt_driver: Unknown H:4 type 0x00
[00:00:01.193,084] <wrn> lpuart: RX: End detected at unexpected state (1).
common_init() after BT_HCI_OP_RESET
common_init() after drv_quirk_no_reset()
common_init() after read_local_ver_complete()
common_init() exit, good
hci_init() just finished common_init()
hci_init() just finished le_init()
[00:00:01.225,341] <inf> bt_hci_core: HW Platform: Nordic Semiconductor (0x0002)
[00:00:01.225,372] <inf> bt_hci_core: HW Variant: nRF52x (0x0002)
[00:00:01.225,433] <inf> bt_hci_core: Firmware: Standard Bluetooth controller (0x00) Version 252.16862 Build 1121034987
hci_init() exit, no error
bt_init() line:4260
bt_init() line:4268
bt_init() line:4276
[00:00:01.227,966] <inf> bt_hci_core: No ID address. App must call settings_load()
[00:00:01.227,996] <inf> central_uart: Bluetooth initialized
[00:00:01.228,363] <err> bt_ecc: Failed to generate ECC key -134
[00:00:01.228,363] <wrn> bt_smp: Public key not available
[00:00:01.231,567] <inf> bt_hci_core: HCI transport: H:4
[00:00:01.231,658] <inf> bt_hci_core: Identity: F1:B2:BA:28:C5:6D (random)
[00:00:01.231,689] <inf> bt_hci_core: HCI: version 6.1 (0x0f) revision 0x1069, manufacturer 0x0059
[00:00:01.231,719] <inf> bt_hci_core: LMP: version 6.1 (0x0f) subver 0x1069
[00:00:01.231,842] <err> bt_gatt: Unable to import the key for AES CMAC -134
[00:00:01.231,964] <inf> central_uart: NUS Client module initialized
[00:00:01.231,994] <inf> central_uart: Scan module initialized
[00:00:01.237,304] <inf> central_uart: Scan started
Starting Bluetooth Central UART sample
[00:00:01.238,098] <err> bt_gatt: Unable to import the key for AES CMAC -134
*** Booting nRF Connect SDK v3.1.1-e2a97fe2578a ***
*** Using Zephyr OS v4.1.99-ff8f0c579eeb ***
[00:00:00.287,353] <inf> fs_nvs: 2 Sectors of 4096 bytes
[00:00:00.287,353] <inf> fs_nvs: alloc wra: 0, fd0
[00:00:00.287,384] <inf> fs_nvs: data wra: 0, 1c
h4_open() entered...
bt_hci_transport_setup() entered...
bt_hci_transport_setup(): draining bytes from uart, c=04
bt_hci_transport_setup(): draining bytes from uart, c=3E
bt_hci_transport_setup(): draining bytes from uart, c=29
bt_hci_transport_setup(): draining bytes from uart, c=02
bt_hci_transport_setup(): draining bytes from uart, c=01
bt_hci_transport_setup(): draining bytes from uart, c=00
bt_hci_transport_setup(): draining bytes from uart, c=00
bt_hci_transport_setup(): draining bytes from uart, c=A4
bt_hci_transport_setup(): draining bytes from uart, c=FA
bt_hci_transport_setup(): draining bytes from uart, c=2A
bt_hci_transport_setup(): draining bytes from uart, c=6A
bt_hci_transport_setup(): draining bytes from uart, c=B4
bt_hci_transport_setup(): draining bytes from uart, c=FA
bt_hci_transport_setup(): draining bytes from uart, c=1D
bt_hci_transport_setup(): draining bytes from uart, c=02
bt_hci_transport_setup(): draining bytes from uart, c=01
bt_hci_transport_setup(): draining bytes from uart, c=06
bt_hci_transport_setup(): draining bytes from uart, c=19
bt_hci_transport_setup(): draining bytes from uart, c=16
bt_hci_transport_setup(): draining bytes from uart, c=F7
bt_hci_transport_setup(): draining bytes from uart, c=FD
bt_hci_transport_setup(): draining bytes from uart, c=01
bt_hci_transport_setup(): draining bytes from uart, c=DF
bt_hci_transport_setup(): draining bytes from uart, c=FF
bt_hci_transport_setup(): draining bytes from uart, c=7D
bt_hci_transport_setup(): draining bytes from uart, c=84
bt_hci_transport_setup(): draining bytes from uart, c=DB
bt_hci_transport_setup(): draining bytes from uart, c=25
bt_hci_transport_setup(): draining bytes from uart, c=54
bt_hci_transport_setup(): draining bytes from uart, c=F4
bt_hci_transport_setup(): draining bytes from uart, c=1B
bt_hci_transport_setup(): draining bytes from uart, c=D0
bt_hci_transport_setup(): draining bytes from uart, c=77
bt_hci_transport_setup(): draining bytes from uart, c=2D
bt_hci_transport_setup(): draining bytes from uart, c=0F
bt_hci_transport_setup(): draining bytes from uart, c=45
bt_hci_transport_setup(): draining bytes from uart, c=C3
bt_hci_transport_setup(): draining bytes from uart, c=65
bt_hci_transport_setup(): draining bytes from uart, c=00
bt_hci_transport_setup(): draining bytes from uart, c=00
bt_hci_transport_setup(): draining bytes from uart, c=00
bt_hci_transport_setup(): draining bytes from uart, c=00
bt_hci_transport_setup(): draining bytes from uart, c=03
bt_hci_transport_setup(): draining bytes from uart, c=A6
bt_hci_transport_setup() about to gpio_pin_set(port, RESET_GPIO_PIN=24, 0)
bt_hci_transport_setup() exit success
h4_open() exit
bt_init() entered...
hci_init() entered...
common_init() entered...
common_init() about to  BT_HCI_OP_RESET
ASSERTION FAIL [err == 0] @ WEST_TOPDIR/zephyr/subsys/bluetooth/host/hci_core.c:505
        Controller unresponsive, command opcode 0x0c03 timeout with err -11
[00:00:10.300,109] <err> os: r0/a1:  0x00000003  r1/a2:  0x00000000  r2/a3:  0x00000002
[00:00:10.300,140] <err> os: r3/a4:  0x00000003 r12/ip:  0x200124dc r14/lr:  0x000104c5
[00:00:10.300,140] <err> os:  xpsr:  0x01000000
[00:00:10.300,170] <err> os: Faulting instruction address (r15/pc): 0x000104d4
[00:00:10.300,201] <err> os: >>> ZEPHYR FATAL ERROR 3: Kernel oops on CPU 0
[00:00:10.300,231] <err> os: Current thread: 0x2000e7e0 (unknown)
[00:00:10.358,123] <err> os: Halting system

The central_uart code and prj.conf have no changes I am aware of other than the CONFIG_LOG... options added for BACKEND_UART.

The board files are modified from the original Vidar code like follows

(v3.1.1) burt@P51:~/ncs/v3.1.1/nrf/samples/bluetooth/central_uart$  diff -rw ~/6431.central_uart/boards boards
Only in boards: nrf5340dk_nrf5340_cpuapp.conf
Only in boards: nrf54h20dk_nrf54h20_cpuapp.conf
Only in boards: nrf54h20dk_nrf54h20_cpuapp.overlay
Only in boards: nrf54l15dk_nrf54l05_cpuapp.conf
Only in boards: nrf54l15dk_nrf54l05_cpuapp.overlay
Only in boards: nrf54l15dk_nrf54l10_cpuapp.conf
Only in boards: nrf54l15dk_nrf54l10_cpuapp.overlay
Only in boards: nrf54l15dk_nrf54l15_cpuapp.conf
Only in boards: nrf54l15dk_nrf54l15_cpuapp.overlay
Only in boards: nrf54lm20dk_nrf54lm20a_cpuapp.conf
Only in boards: nrf54lm20dk_nrf54lm20a_cpuapp.overlay
Only in boards: nrf54lm20pdk_nrf54lm20a_cpuapp.conf
Only in boards: nrf54lm20pdk_nrf54lm20a_cpuapp.overlay
Only in boards: nrf54lv10dk_nrf54lv10a_cpuapp.conf
Only in boards: nrf54lv10dk_nrf54lv10a_cpuapp.overlay
diff -rw /home/burt/6431.central_uart/boards/nrf9160dk_nrf9160_ns_0_14_0.overlay boards/nrf9160dk_nrf9160_ns_0_14_0.overlay
2c2
< #include <nrf9160dk_nrf52840_reset_on_if9.dtsi>
---
> #include <nrf9160/nrf9160dk_nrf52840_reset_on_if9.dtsi>
diff -rw /home/burt/6431.central_uart/boards/nrf9160dk_nrf9160_ns.conf boards/nrf9160dk_nrf9160_ns.conf
10a11,13
> 
> #BMS CONFIG_TFM_PROFILE_TYPE_MINIMAL=n
> #BMS CONFIG_TFM_PROFILE_TYPE_NOT_SET=y
diff -rw /home/burt/6431.central_uart/boards/nrf9160dk_nrf9160_ns.overlay boards/nrf9160dk_nrf9160_ns.overlay
1c1
< #include <nrf9160dk_nrf52840_reset_on_if5.dtsi>
---
> #include <nrf9160/nrf9160dk_nrf52840_reset_on_if5.dtsi>
6a7,8
>         zephyr,bt-hci = &bt_hci_uart;
> 
26a29,34
>               //following 4 lines are added from lte_ble_gateway
>                 bt_hci_uart: bt_hci_uart {
>                         compatible = "zephyr,bt-hci-uart";
>                         status = "okay";
>                 };
> 

Thank you for help with this. Note that I am testing with my external custom nRF52832 board off. That board runs bluetooth/samples/peripheral_uart normally.

Burt Silverman

[Vidar Berg]

Hi Burt,

Is it possible to get logging from the nRF52832 hci controller as well, and if not, are you able to probe the PINRESET input on it do see if it's driven low by the 9160 on startup? Also, I don't remember when I created this sample, do you have a link to that case? And did this work reliably in a previous SDK version? 

Thanks,

Vidar

[Burt]

Hi Vidar, thank you for getting involved. The original ticket where you provided 6431.central_uart to us is (+) BLE communication between a nRF52 DK board and a nRF9160 DK board - Nordic Q&A - Nordic DevZone - Nordic DevZone. I need to try the code on some older versions of SDK such as v2.5.0; I believe that is where we started. I was not involved until very recently, when the project was moved from back burner to front burner. I know that the nRF52840 on the nRF9160DK is getting reset because I can go to its console and see boot messages after I reset the nRF9160. I will try to get logging from the nRF52840 controller. Will get back to you on that.

Burt

[Vidar Berg]

Hi Burt,

I have now. Yes, after the fix I was able to make it work. To apply the commit I opened the terminal, CDed to the v3.1.1/zephyr folder, then ran the following commands:

git remote add upstream https://github.com/zephyrproject-rtos/zephyr.git
git fetch upstream
git cherry-pick 9227a7c131a6763dfaa298e8c833373fe8c1623e

The fix will also be included in the upcoming SDK v3.2.0 release. It's currently available in v3.2.0-rc2. 

Log output host:

[00:00:00.407,440] <inf> fs_nvs: 2 Sectors of 4096 bytes
[00:00:00.407,470] <inf> fs_nvs: alloc wra: 0, fe8
[00:00:00.407,470] <inf> fs_nvs: data wra: 0, 0
[00:00:01.184,692] <inf> bt_hci_core: HW Platform: Nordic Semiconductor (0x0002)
[00:00:01.184,722] <inf> bt_hci_core: HW Variant: nRF52x (0x0002)
[00:00:01.184,753] <inf> bt_hci_core: Firmware: Standard Bluetooth controller (0x00) Version 252.16862 Build 1121034987
[00:00:01.189,300] <inf> bt_hci_core: No ID address. App must call settings_load()
[00:00:01.189,331] <inf> central_uart: Bluetooth initialized
[00:00:01.197,082] <inf> bt_hci_core: HCI transport: H:4
[00:00:01.197,204] <inf> bt_hci_core: Identity: F3:2D:57:2C:CF:0B (random)
[00:00:01.197,235] <inf> bt_hci_core: HCI: version 6.1 (0x0f) revision 0x1069, manufacturer 0x0059
[00:00:01.197,265] <inf> bt_hci_core: LMP: version 6.1 (0x0f) subver 0x1069
[00:00:01.220,977] <inf> cened
[00:00:00.401,550] <inf> fs_nvs: 2 Sectors of 4096 bytes
[00:00:00.401,580] <inf> fs_nvs: alloc wra: 0, fd0
[00:00:00.401,580] <inf> fs_nvs: data wra: 0, 1c
[00:00:01.146,392] <inf> bt_hci_core: HW Platform: Nordic Semiconductor (0x0002)
[00:00:01.146,423] <inf> bt_hci_core: HW Variant: nRF52x (0x0002)
[00:00:01.146,453] <inf> bt_hci_core: Firmware: Standard Bluetooth controller (0x00) Version 252.16862 Build 1121034987
[00:00:01.148,925] <inf> bt_hci_core: No ID address. App must call settings_load()
[00:00:01.148,925] <inf> central_uart: Bluetooth initialized
[00:00:01.152,679] <inf> bt_hci_core: HCI transport: H:4
[00:00:01.152,770] <inf> bt_hci_core: Identity: F3:2D:57:2C:CF:0B (random)
[00:00:01.152,801] <inf> bt_hci_core: HCI: version 6.1 (0x0f) revision 0x1069, manufacturer 0x0059
[00:00:01.152,832] <inf> bt_hci_core: LMP: version 6.1 (0x0f) subver 0x1069
[00:00:01.179,931] <inf> central_uart: NUS Client module initialized
[00:00:01.179,962] <inf> central_uart: Scan module initialized
[00:00:01.185,424] <inf> central_uart: Scan started

Project used (configured for 52840 DK + 9151 DK)

central_uart_nrf91.zip

Best regards,

Vidar

[Burt]

Hi Vidar,

I don't know what I am doing wrong, but I tried building in v3.2.0-rc2, and I get this when running

** Booting nRF Connect SDK v3.2.0-rc2-45be7e87c461 ***
*** Using Zephyr OS v4.2.99-7b2862b457c3 ***
[00:00:00.336,975] <inf> fs_nvs: 2 Sectors of 4096 bytes
[00:00:00.337,005] <inf> fs_nvs: alloc wra: 0, fe8
[00:00:00.337,005] <inf> fs_nvs: data wra: 0, 0
[00:00:01.046,447] <err> bt_driver: Unknown H:4 type 0x82
[00:00:01.046,539] <wrn> lpuart: RX: End detected at unexpected state (1).
[00:00:01.047,607] <err> bt_driver: Unknown H:4 type 0x0e
[00:00:01.048,736] <err> bt_driver: Unknown H:4 type 0x03
[00:00:01.049,896] <err> bt_driver: Unknown H:4 type 0x01
[00:00:01.051,025] <err> bt_driver: Unknown H:4 type 0x00
[00:00:01.052,124] <err> bt_driver: Unknown H:4 type 0x00
ASSERTION FAIL [err == 0] @ WEST_TOPDIR/zephyr/subsys/bluetooth/host/hci_core.c:504
        Controller unresponsive, command opcode 0x0c03 timeout with err -11
[00:00:10.347,717] <err> os: r0/a1:  0x00000003  r1/a2:  0x00000000  r2/a3:  0x00000002
[00:00:10.347,747] <err> os: r3/a4:  0x00000003 r12/ip:  0x2001fdcc r14/lr:  0x00048445
[00:00:10.347,747] <err> os:  xpsr:  0x01000000
[00:00:10.347,747] <err> os: Faulting instruction address (r15/pc): 0x00048454
[00:00:10.347,808] <err> os: >>> ZEPHYR FATAL ERROR 3: Kernel oops on CPU 0
[00:00:10.347,839] <err> os: Current thread: 0x2001c100 (unknown)
[00:00:10.405,548] <err> os: Halting system

It's a bit difficult not having the recommended board overlay files for nRF9160DK as I do not have an nRF9151DK board.

Burt

[Burt]

Vidar, have you tested with including debug.conf when building hci_lpuart? I always enable that when things don't work out the very first time without it. That path needs to be tested given that the debug.conf file exists. I will try again now without using that debug.conf.

Burt

[Burt]

I just turned off debug.conf when building hci_lpuart sample, and I am getting some build garbage when doing a pristine build in v3.2.0-rc2:

warning: BT_BUF_EVT_DISCARDABLE_SIZE (defined at subsys/bluetooth/host/Kconfig:172,
drivers/bluetooth/hci/Kconfig.nxp:60, subsys/bluetooth/host/Kconfig:172) was assigned the value
'255' but got the value ''. Check these unsatisfied dependencies: ((BT_HCI_HOST && BT_RPC_STACK) ||
(BT_NXP && BT_HCI && BT_DRIVERS) || (BT_HCI_HOST && BT_HCI && BT)) (=n). See
docs.zephyrproject.org/.../kconfig.html and/or look up
BT_BUF_EVT_DISCARDABLE_SIZE in the menuconfig/guiconfig interface. The Application Development
Primer, Setting Configuration Values, and Kconfig - Tips and Best Practices sections of the manual
might be helpful too.


warning: BT_CTLR_DTM_HCI (defined at subsys/bluetooth/controller/Kconfig.dtm:14) was assigned the
value 'y' but got the value 'n'. Check these unsatisfied dependencies: BT_CTLR_DTM_HCI_SUPPORT (=n).
See docs.zephyrproject.org/.../kconfig.html and/or look up
BT_CTLR_DTM_HCI in the menuconfig/guiconfig interface. The Application Development Primer, Setting
Configuration Values, and Kconfig - Tips and Best Practices sections of the manual might be helpful
too.

[Burt]

There were bugs in the .conf files so I had to do something like:

(v3.2.0-rc2) burt@P51:~/ncs/v3.2.0-rc2/nrf/samples/bluetooth/hci_lpuart$ git diff .
diff --git a/samples/bluetooth/hci_lpuart/boards/nrf9160dk_nrf52840.conf b/samples/bluetooth/hci_lpuart/boards/nrf9160dk_nrf52840.conf
index c6a0424420..f611f52b2e 100644
--- a/samples/bluetooth/hci_lpuart/boards/nrf9160dk_nrf52840.conf
+++ b/samples/bluetooth/hci_lpuart/boards/nrf9160dk_nrf52840.conf
@@ -3,7 +3,7 @@
 CONFIG_GPIO=y
 CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=512
 CONFIG_BT_MAX_CONN=16
-CONFIG_BT_CTLR_DTM_HCI=y
+#CONFIG_BT_CTLR_DTM_HCI=y
 CONFIG_BT_CTLR_ASSERT_HANDLER=y
 
 CONFIG_UART_1_ASYNC=y
diff --git a/samples/bluetooth/hci_lpuart/prj.conf b/samples/bluetooth/hci_lpuart/prj.conf
index 1997b45e3a..6371f8e11c 100644
--- a/samples/bluetooth/hci_lpuart/prj.conf
+++ b/samples/bluetooth/hci_lpuart/prj.conf
@@ -5,4 +5,5 @@ CONFIG_BT_HCI_RAW=y
 CONFIG_BT_HCI_RAW_H4=y
 CONFIG_BT_HCI_RAW_H4_ENABLE=y
 CONFIG_BT_BUF_ACL_RX_SIZE=251
-CONFIG_BT_BUF_EVT_DISCARDABLE_SIZE=255
+#CONFIG_BT_BUF_EVT_DISCARDABLE_SIZE=255

Still nothing works for me.

[Vidar Berg]

I tested with the last release candidate now and found that I had to add CONFIG_BT_BUF_ACL_RX_SIZE=251 to the application configuration to align the buffer ACL sizes between host and controller (controller does not support reassembly like a generic controller, hence this requirement), and also uncomment the CONFIG_NRFX_UARTE0=y line. But it worked after making these two changes. Can you check if the controller board is reset when bt_enable is called or if the custom bt_hci_transport_setup() from nrf52840_reset.c is being called at all? This resetting of the controller is needed to ensure the host and controller are in sync before performing the initialisation.

[Burt]

Hi Vidar,

I was almost ready to say "it works," but after more tries I have to modify that to "it works, quite often."

The CONFIG_BT_BUF_ACL_RX_SIZE=251 definitely is what made it work "quite often." And the CONFIG_NRFX_UARTE0=y line I do not see in v3.2.0-rc2. I do see CONFIG_NRFX_UARTE=y uncommented in prj.conf. But I did see it in v3.1.1. Now, it is defined in zephyr/drivers/serial/Kconfig.nrfx_uart_instance and is not user configurable

config NRFX_UARTE$(nrfx_uart_num)
        def_bool y if HAS_HW_NRF_UARTE$(nrfx_uart_num) && !UART_NRFX_UARTE_LEGACY_SHIM

so it should not show up in prj.conf. Nevertheless, I do see

CONFIG_HAS_HW_NRF_UARTE0=y
CONFIG_HAS_HW_NRF_UARTE2=y

in build/central_uart/zephyr/.config, but I also see 

CONFIG_UART_NRFX_UARTE_LEGACY_SHIM=y

in that file. I could set CONFIG_UART_NRFX_UARTE_LEGACY_SHIM=n but according to zephyr/drivers/serial/Kconfig.nrfx, doing that is deprecated. So we are in limbo--can you take another look at what is really needed for CONFIG_NRFX_UARTE0?

Having talked about these details, and yes, I do see that the controller board is reset after I start central_uart, the problem I am having is that eventually something gets out of sync and the system does not come up to Bluetooth initialized. You may have to try it quite a few times, but it is happening for me within a minute or two of continued resets. The strange thing is that once it happens, something is stuck in memory so that it usually stays out of sync until doing a power on reset (rather than push button reset).

Burt

[Vidar Berg]

Hi Burt,

I had a chance to do some more testing with the v3.2.0 release tag, but I wasn’t able to reproduce the reliability issue. I performed multiple resets and also tried a different peripheral sample to stress test the system by repeatedly connecting and disconnecting and sending notifications at a high rate. The CONFIG_NRFX_UARTE0 symbol has been removed now, see migration doc:

https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/releases_and_maturity/migration/migration_guide_3.2.html#nrfx 

Including .config file from my host and controller build for comparison (to compare the UART configuration)

# CONFIG_INPUT is not set
# CONFIG_WIFI is not set
# CONFIG_REGULATOR is not set
CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=1024
CONFIG_BT_LONG_WQ_STACK_SIZE=1800
CONFIG_MAIN_STACK_SIZE=4096
# CONFIG_FPU is not set
CONFIG_BT_RX_STACK_SIZE=1200
CONFIG_SERIAL=y
# CONFIG_SPI is not set
# CONFIG_MIPI_DSI is not set
# CONFIG_MEMC is not set
# CONFIG_MODEM is not set
CONFIG_UART_INTERRUPT_DRIVEN=y
CONFIG_BT_HCI_ACL_FLOW_CONTROL=y
CONFIG_BT_HCI_VS=y
CONFIG_HW_STACK_PROTECTION=y
CONFIG_BOARD_NRF9151DK=y
# CONFIG_BT_WAIT_NOP is not set
# CONFIG_I2C is not set
CONFIG_NUM_IRQS=65
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC=32768
CONFIG_FLASH_SIZE=1024
CONFIG_FLASH_BASE_ADDRESS=0x0
CONFIG_MP_MAX_NUM_CPUS=1
CONFIG_SOC_RESET_HOOK=y
CONFIG_CLOCK_CONTROL=y
CONFIG_IDLE_STACK_SIZE=320
CONFIG_ISR_STACK_SIZE=2048
CONFIG_SYS_CLOCK_TICKS_PER_SEC=32768
CONFIG_ROM_START_OFFSET=0
CONFIG_KERNEL_ENTRY="__start"
CONFIG_BUILD_OUTPUT_BIN=y
CONFIG_XIP=y
CONFIG_HAS_FLASH_LOAD_OFFSET=y
# CONFIG_COUNTER is not set
# CONFIG_SRAM_VECTOR_TABLE is not set
CONFIG_CPU_HAS_ARM_MPU=y
# CONFIG_SHARED_INTERRUPTS is not set
# CONFIG_PM_DEVICE is not set
CONFIG_TICKLESS_KERNEL=y
CONFIG_BT_AUTO_PHY_UPDATE=y
CONFIG_BT_AUTO_DATA_LEN_UPDATE=y
# CONFIG_BT_USER_PHY_UPDATE is not set
CONFIG_CLOCK_CONTROL_INIT_PRIORITY=30
CONFIG_USE_DT_CODE_PARTITION=y
CONFIG_BUILD_WITH_TFM=y
# CONFIG_MULTI_LEVEL_INTERRUPTS is not set
# CONFIG_ZERO_LATENCY_IRQS is not set
CONFIG_NUM_PREEMPT_PRIORITIES=15
CONFIG_NUM_METAIRQ_PRIORITIES=0
CONFIG_GEN_IRQ_VECTOR_TABLE=y
# CONFIG_DYNAMIC_INTERRUPTS is not set
CONFIG_GEN_ISR_TABLES=y
# CONFIG_INIT_STACKS is not set
CONFIG_TIMESLICE_SIZE=20
CONFIG_FLASH_LOAD_OFFSET=0x50000
CONFIG_SYS_CLOCK_EXISTS=y
CONFIG_INIT_ARCH_HW_AT_BOOT=y
# CONFIG_BUILD_OUTPUT_S19 is not set
CONFIG_BUILD_OUTPUT_HEX=y
CONFIG_ARCH_HAS_CUSTOM_BUSY_WAIT=y
# CONFIG_FLASH is not set
# CONFIG_HCI_NXP_ENABLE_AUTO_SLEEP is not set
# CONFIG_HCI_NXP_SET_CAL_DATA is not set
CONFIG_BT_BUF_EVT_RX_COUNT=11
CONFIG_BT_BUF_ACL_TX_COUNT=10
# CONFIG_POWER_DOMAIN is not set
# CONFIG_MFD is not set
# CONFIG_HCI_NXP_RX_THREAD is not set
CONFIG_GPIO=y
# CONFIG_CPU_HAS_CUSTOM_FIXED_SOC_MPU_REGIONS is not set
# CONFIG_CODE_DATA_RELOCATION_SRAM is not set
# CONFIG_CACHE is not set
CONFIG_LOG=y
CONFIG_CMSIS_CORE_HAS_SYSTEM_CORE_CLOCK=y
# CONFIG_CODE_DATA_RELOCATION is not set
# CONFIG_ROMSTART_RELOCATION_ROM is not set
CONFIG_DCACHE_LINE_SIZE=32
# CONFIG_RESET is not set
CONFIG_ARCH_SW_ISR_TABLE_ALIGN=4
CONFIG_LOG_DOMAIN_NAME=""
# CONFIG_ASSERT is not set
CONFIG_LOG_PROCESS_THREAD_STACK_SIZE=768
# CONFIG_DEVICE_DEPS is not set
CONFIG_SOC_HAS_TIMING_FUNCTIONS=y
# CONFIG_UART_USE_RUNTIME_CONFIGURE is not set
# CONFIG_SYSCON is not set
CONFIG_CONSOLE=y
# CONFIG_WINSTREAM is not set
CONFIG_COMMON_LIBC_MALLOC_ARENA_SIZE=-1
CONFIG_GEN_SW_ISR_TABLE=y
# CONFIG_REBOOT is not set
CONFIG_GEN_IRQ_START_VECTOR=0
CONFIG_SRAM_OFFSET=0
CONFIG_ARCH_IRQ_VECTOR_TABLE_ALIGN=4
CONFIG_ISR_TABLES_LOCAL_DECLARATION_SUPPORTED=y
# CONFIG_BOOTLOADER_MCUBOOT is not set
# CONFIG_SCHED_CPU_MASK is not set
CONFIG_BT_BUF_CMD_TX_COUNT=1
CONFIG_KERNEL_MEM_POOL=y
CONFIG_MULTITHREADING=y
# CONFIG_OUTPUT_DISASSEMBLY is not set
# CONFIG_WATCHDOG is not set
CONFIG_ICACHE_LINE_SIZE=32
CONFIG_BT_BUF_CMD_TX_SIZE=65
CONFIG_BT_BUF_EVT_RX_SIZE=68
CONFIG_BT_BUF_ACL_TX_SIZE=251
CONFIG_BT_BUF_ACL_RX_SIZE=251
CONFIG_BT_L2CAP_TX_MTU=247

#
# Devicetree Info
#
CONFIG_DT_HAS_ARDUINO_UNO_ADC_ENABLED=y
CONFIG_DT_HAS_ARDUINO_HEADER_R3_ENABLED=y
CONFIG_DT_HAS_ARM_ARMV8M_MPU_ENABLED=y
CONFIG_DT_HAS_ARM_CORTEX_M33F_ENABLED=y
CONFIG_DT_HAS_ARM_V8M_NVIC_ENABLED=y
CONFIG_DT_HAS_FIXED_PARTITIONS_ENABLED=y
CONFIG_DT_HAS_FIXED_SUBPARTITIONS_ENABLED=y
CONFIG_DT_HAS_GPIO_KEYS_ENABLED=y
CONFIG_DT_HAS_GPIO_LEDS_ENABLED=y
CONFIG_DT_HAS_MMIO_SRAM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CLOCK_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_DPPIC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_EGU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIOTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPREGRET_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_IPC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_KMU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_PINCTRL_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_POWER_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SAADC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SW_LPUART_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_TWIM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UARTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_VMC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_WDT_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF91_FLASH_CONTROLLER_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF91X_REGULATORS_ENABLED=y
CONFIG_DT_HAS_PWM_LEDS_ENABLED=y
CONFIG_DT_HAS_SOC_NV_FLASH_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_BT_HCI_UART_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_PSA_CRYPTO_RNG_ENABLED=y
# end of Devicetree Info

#
# Modules
#
# CONFIG_BUILD_ONLY_NO_BLOBS is not set

#
# Available modules.
#

#
# nrf (/opt/nordic/ncs/v3.1.1/nrf)
#
CONFIG_LOG_BUFFER_SIZE=1024
CONFIG_MBEDTLS_MPI_MAX_SIZE=384
CONFIG_MBEDTLS_HEAP_SIZE=512
CONFIG_MBEDTLS_PSA_KEY_SLOT_COUNT=32
CONFIG_MPSL_WORK_STACK_SIZE=1024
CONFIG_MBEDTLS=y
# CONFIG_MBEDTLS_TLS_VERSION_1_2 is not set
CONFIG_MBEDTLS_MAC_SHA256_ENABLED=y
# CONFIG_MBEDTLS_CTR_DRBG_ENABLED is not set
# CONFIG_MBEDTLS_MD_C is not set
# CONFIG_MBEDTLS_TLS_LIBRARY is not set
# CONFIG_MBEDTLS_X509_LIBRARY is not set
CONFIG_MBEDTLS_ENABLE_HEAP=y
CONFIG_MBEDTLS_PSA_CRYPTO_STORAGE_C=y
# CONFIG_MBEDTLS_LEGACY_CRYPTO_C is not set
CONFIG_TFM_CRYPTO_RNG_MODULE_ENABLED=y
CONFIG_TFM_PARTITION_CRYPTO=y
CONFIG_TFM_PARTITION_PLATFORM=y

#
# Nordic nRF Connect
#
CONFIG_WARN_EXPERIMENTAL=y
CONFIG_NORDIC_QSPI_NOR_FLASH_LAYOUT_PAGE_SIZE=4096
CONFIG_NRF_SECURITY_ENABLER=y
# CONFIG_NCS_SAMPLES_DEFAULTS is not set

#
# Image build variants
#
# CONFIG_NCS_MCUBOOT_IN_BUILD is not set
# end of Image build variants

# CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU_SPEEDUP is not set

#
# Subsystems
#

#
# Bootloader
#
# CONFIG_SECURE_BOOT is not set
CONFIG_PM_PARTITION_SIZE_PROVISION=0x280
# CONFIG_B0_MIN_PARTITION_SIZE is not set
CONFIG_PM_PARTITION_SIZE_B0_IMAGE=0x8000
# CONFIG_IS_SECURE_BOOTLOADER is not set

#
# Secure Boot firmware validation
#
CONFIG_SB_VALIDATION_INFO_MAGIC=0x86518483
CONFIG_SB_VALIDATION_POINTER_MAGIC=0x6919b47e
CONFIG_SB_VALIDATION_INFO_CRYPTO_ID=1
CONFIG_SB_VALIDATION_INFO_VERSION=2
CONFIG_SB_VALIDATION_METADATA_OFFSET=0
CONFIG_SB_VALIDATION_STRUCT_HAS_HASH=y
CONFIG_SB_VALIDATION_STRUCT_HAS_PUBLIC_KEY=y
CONFIG_SB_VALIDATE_FW_SIGNATURE=y
# end of Secure Boot firmware validation

# CONFIG_SECURE_BOOT_STORAGE is not set
# CONFIG_MCUBOOT_COMPRESSED_IMAGE_SUPPORT_ENABLED is not set
# CONFIG_MCUBOOT_BOOTLOADER_SIGNATURE_TYPE_ED25519 is not set
# CONFIG_MCUBOOT_BOOTLOADER_SIGNATURE_TYPE_PURE is not set
# CONFIG_NCS_MCUBOOT_BOOTLOADER_SIGN_MERGED_BINARY is not set
# CONFIG_NCS_MCUBOOT_MANIFEST_UPDATES is not set
# end of Bootloader

#
# Bluetooth Low Energy
#
CONFIG_BT_COMPANY_ID_NORDIC=0x0059
CONFIG_BT_COMPANY_ID=0x0059
CONFIG_BT_MAX_CONN=1
CONFIG_BT_LL_SOFTDEVICE_HEADERS_INCLUDE=y
CONFIG_BT_HCI_TX_STACK_SIZE=512
# CONFIG_BT_RADIO_NOTIFICATION_CONN_CB is not set

#
# BLE Libraries
#
# CONFIG_BT_GATT_POOL is not set
# CONFIG_BT_GATT_DM is not set
# CONFIG_BT_ADV_PROV is not set
# CONFIG_BT_CONN_CTX is not set

#
# Bluetooth Services
#
# CONFIG_BT_AMS_CLIENT is not set
# CONFIG_BT_ANCS_CLIENT is not set
# CONFIG_BT_BAS_CLIENT is not set
# CONFIG_BT_BMS is not set
# CONFIG_BT_CTS_CLIENT is not set
# CONFIG_BT_DFU_SMP is not set
# CONFIG_BT_GATTP is not set
# CONFIG_BT_HIDS is not set
# CONFIG_BT_HOGP is not set
# CONFIG_BT_LBS is not set
# CONFIG_BT_NSMS is not set
# CONFIG_BT_NUS is not set
# CONFIG_BT_NUS_CLIENT is not set
# CONFIG_BT_RSCS is not set
# CONFIG_BT_THROUGHPUT is not set
# CONFIG_BT_LATENCY is not set
# CONFIG_BT_LATENCY_CLIENT is not set
# CONFIG_BT_HRS_CLIENT is not set
# CONFIG_BT_DDFS is not set
# CONFIG_BT_MDS is not set
# CONFIG_BT_CGMS is not set
# CONFIG_BT_FAST_PAIR is not set
CONFIG_SYSTEM_WORKQUEUE_PRIORITY=-1
# end of Bluetooth Services

#
# BLE over nRF RPC
#
# CONFIG_BT_RPC is not set
CONFIG_HEAP_MEM_POOL_SIZE=512
# CONFIG_BT_SHELL is not set
CONFIG_BT_CONN_DYNAMIC_CALLBACKS=y
# CONFIG_BT_RPC_STACK is not set
# CONFIG_BT_CENTRAL is not set
CONFIG_BT_PERIPHERAL=y
# CONFIG_BT_OBSERVER is not set
CONFIG_BT_BROADCASTER=y
CONFIG_BT_CONN=y
# CONFIG_BT_REMOTE_VERSION is not set
CONFIG_BT_PHY_UPDATE=y
CONFIG_BT_DATA_LEN_UPDATE=y
# CONFIG_BT_EXT_ADV is not set
CONFIG_BT_LOG=y
# CONFIG_BT_LOG_LEVEL_OFF is not set
# CONFIG_BT_LOG_LEVEL_ERR is not set
# CONFIG_BT_LOG_LEVEL_WRN is not set
# CONFIG_BT_LOG_LEVEL_INF is not set
# CONFIG_BT_LOG_LEVEL_DBG is not set
CONFIG_BT_LOG_LEVEL_DEFAULT=y
CONFIG_BT_LOG_LEVEL=3
CONFIG_BT_HCI_DRIVER_LOG_LEVEL_INHERIT=y
CONFIG_BT_HCI_DRIVER_LOG_LEVEL=3
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_OFF is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_ERR is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_WRN is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_INF is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_DBG is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_RPA_LOG_LEVEL_INHERIT=y
CONFIG_BT_RPA_LOG_LEVEL=3
# CONFIG_BT_RPA_LOG_LEVEL_OFF is not set
# CONFIG_BT_RPA_LOG_LEVEL_ERR is not set
# CONFIG_BT_RPA_LOG_LEVEL_WRN is not set
# CONFIG_BT_RPA_LOG_LEVEL_INF is not set
# CONFIG_BT_RPA_LOG_LEVEL_DBG is not set
# CONFIG_BT_RPA_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_ATT_LOG_LEVEL_INHERIT=y
CONFIG_BT_ATT_LOG_LEVEL=3
# CONFIG_BT_ATT_LOG_LEVEL_OFF is not set
# CONFIG_BT_ATT_LOG_LEVEL_ERR is not set
# CONFIG_BT_ATT_LOG_LEVEL_WRN is not set
# CONFIG_BT_ATT_LOG_LEVEL_INF is not set
# CONFIG_BT_ATT_LOG_LEVEL_DBG is not set
# CONFIG_BT_ATT_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_GATT_LOG_LEVEL_INHERIT=y
CONFIG_BT_GATT_LOG_LEVEL=3
# CONFIG_BT_GATT_LOG_LEVEL_OFF is not set
# CONFIG_BT_GATT_LOG_LEVEL_ERR is not set
# CONFIG_BT_GATT_LOG_LEVEL_WRN is not set
# CONFIG_BT_GATT_LOG_LEVEL_INF is not set
# CONFIG_BT_GATT_LOG_LEVEL_DBG is not set
# CONFIG_BT_GATT_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_L2CAP_LOG_LEVEL_INHERIT=y
CONFIG_BT_L2CAP_LOG_LEVEL=3
# CONFIG_BT_L2CAP_LOG_LEVEL_OFF is not set
# CONFIG_BT_L2CAP_LOG_LEVEL_ERR is not set
# CONFIG_BT_L2CAP_LOG_LEVEL_WRN is not set
# CONFIG_BT_L2CAP_LOG_LEVEL_INF is not set
# CONFIG_BT_L2CAP_LOG_LEVEL_DBG is not set
# CONFIG_BT_L2CAP_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_HCI_CORE_LOG_LEVEL_INHERIT=y
CONFIG_BT_HCI_CORE_LOG_LEVEL=3
# CONFIG_BT_HCI_CORE_LOG_LEVEL_OFF is not set
# CONFIG_BT_HCI_CORE_LOG_LEVEL_ERR is not set
# CONFIG_BT_HCI_CORE_LOG_LEVEL_WRN is not set
# CONFIG_BT_HCI_CORE_LOG_LEVEL_INF is not set
# CONFIG_BT_HCI_CORE_LOG_LEVEL_DBG is not set
# CONFIG_BT_HCI_CORE_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_CONN_LOG_LEVEL_INHERIT=y
CONFIG_BT_CONN_LOG_LEVEL=3
# CONFIG_BT_CONN_LOG_LEVEL_OFF is not set
# CONFIG_BT_CONN_LOG_LEVEL_ERR is not set
# CONFIG_BT_CONN_LOG_LEVEL_WRN is not set
# CONFIG_BT_CONN_LOG_LEVEL_INF is not set
# CONFIG_BT_CONN_LOG_LEVEL_DBG is not set
# CONFIG_BT_CONN_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_KEYS_LOG_LEVEL_INHERIT=y
CONFIG_BT_KEYS_LOG_LEVEL=3
# CONFIG_BT_KEYS_LOG_LEVEL_OFF is not set
# CONFIG_BT_KEYS_LOG_LEVEL_ERR is not set
# CONFIG_BT_KEYS_LOG_LEVEL_WRN is not set
# CONFIG_BT_KEYS_LOG_LEVEL_INF is not set
# CONFIG_BT_KEYS_LOG_LEVEL_DBG is not set
# CONFIG_BT_KEYS_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_SERVICE_LOG_LEVEL_INHERIT=y
CONFIG_BT_SERVICE_LOG_LEVEL=3
# CONFIG_BT_SERVICE_LOG_LEVEL_OFF is not set
# CONFIG_BT_SERVICE_LOG_LEVEL_ERR is not set
# CONFIG_BT_SERVICE_LOG_LEVEL_WRN is not set
# CONFIG_BT_SERVICE_LOG_LEVEL_INF is not set
# CONFIG_BT_SERVICE_LOG_LEVEL_DBG is not set
# CONFIG_BT_SERVICE_LOG_LEVEL_DEFAULT is not set
# CONFIG_BT_DIS is not set
# CONFIG_BT_CTS is not set
# CONFIG_BT_HRS is not set
# CONFIG_BT_TPS is not set
# CONFIG_BT_ZEPHYR_NUS is not set
# CONFIG_BT_IAS is not set
# CONFIG_BT_IAS_CLIENT is not set
# CONFIG_BT_OTS is not set
# CONFIG_BT_OTS_CLIENT is not set
# CONFIG_BT_BAS is not set
# CONFIG_BT_BAS_BLS is not set
CONFIG_BT_BUF_ACL_RX_COUNT_EXTRA=1
# CONFIG_BT_HCI_VS_EXT_DETECT is not set
CONFIG_BT_ASSERT=y
CONFIG_BT_ASSERT_VERBOSE=y
# CONFIG_BT_ASSERT_PANIC is not set
# CONFIG_BT_HCI_ERR_TO_STR is not set
CONFIG_BT_DEBUG_NONE=y
# CONFIG_BT_DEBUG_MONITOR_UART is not set
CONFIG_BT_LONG_WQ=y
CONFIG_BT_LONG_WQ_PRIO=10
CONFIG_BT_LONG_WQ_INIT_PRIO=50
CONFIG_BT_HCI_HOST=y
# CONFIG_BT_HCI_TX_STACK_SIZE_WITH_PROMPT is not set
CONFIG_BT_HCI_TX_PRIO=7
# CONFIG_BT_RECV_WORKQ_SYS is not set
CONFIG_BT_RECV_WORKQ_BT=y
CONFIG_BT_RX_PRIO=8
CONFIG_BT_DRIVER_RX_HIGH_PRIO=6
# CONFIG_BT_CONN_TX_NOTIFY_WQ is not set
# CONFIG_BT_AUDIO is not set
CONFIG_BT_BUF_EVT_DISCARDABLE_SIZE=43
CONFIG_BT_BUF_EVT_DISCARDABLE_COUNT=3
CONFIG_BT_HOST_CRYPTO=y
CONFIG_BT_HOST_CRYPTO_PRNG=y
# CONFIG_BT_FILTER_ACCEPT_LIST is not set
CONFIG_BT_LIM_ADV_TIMEOUT=30
CONFIG_BT_CONN_TX_USER_DATA_SIZE=16
CONFIG_BT_CONN_FRAG_COUNT=1
CONFIG_BT_CONN_TX_MAX=10
# CONFIG_BT_CONN_PARAM_ANY is not set
# CONFIG_BT_CONN_CHECK_NULL_BEFORE_CREATE is not set
# CONFIG_BT_USER_DATA_LEN_UPDATE is not set
# CONFIG_BT_REMOTE_INFO is not set
# CONFIG_BT_SMP is not set
CONFIG_BT_L2CAP_TX_BUF_COUNT=10
CONFIG_BT_L2CAP_TX_FRAG_COUNT=2
# CONFIG_BT_L2CAP_SEG_RECV is not set
# CONFIG_BT_L2CAP_RECONFIGURE_EXPLICIT is not set
# CONFIG_BT_ATT_ERR_TO_STR is not set
CONFIG_BT_ATT_TX_COUNT=10
CONFIG_BT_ATT_PREPARE_COUNT=2
# CONFIG_BT_ATT_SENT_CB_AFTER_TX is not set
CONFIG_BT_GATT_SERVICE_CHANGED=y
# CONFIG_BT_GATT_DYNAMIC_DB is not set
CONFIG_BT_GATT_CACHING=y
# CONFIG_BT_GATT_NOTIFY_MULTIPLE is not set
# CONFIG_BT_GATT_ENFORCE_CHANGE_UNAWARE is not set
CONFIG_BT_GATT_ENFORCE_SUBSCRIPTION=y
# CONFIG_BT_GATT_CLIENT is not set
CONFIG_BT_GATT_READ_MULTIPLE=y
CONFIG_BT_GATT_READ_MULT_VAR_LEN=y
CONFIG_BT_GAP_AUTO_UPDATE_CONN_PARAMS=y
CONFIG_BT_GAP_PERIPHERAL_PREF_PARAMS=y
CONFIG_BT_PERIPHERAL_PREF_MIN_INT=12
CONFIG_BT_PERIPHERAL_PREF_MAX_INT=12
CONFIG_BT_PERIPHERAL_PREF_LATENCY=0
CONFIG_BT_PERIPHERAL_PREF_TIMEOUT=400
# CONFIG_BT_GATT_AUTHORIZATION_CUSTOM is not set
CONFIG_BT_MAX_PAIRED=0
CONFIG_BT_CREATE_CONN_TIMEOUT=3
CONFIG_BT_CONN_PARAM_UPDATE_TIMEOUT=5000
CONFIG_BT_CONN_PARAM_RETRY_COUNT=3
CONFIG_BT_CONN_PARAM_RETRY_TIMEOUT=5000
# CONFIG_BT_DEVICE_NAME_DYNAMIC is not set
CONFIG_BT_DEVICE_NAME="throughput_test"
# CONFIG_BT_DEVICE_APPEARANCE_DYNAMIC is not set
CONFIG_BT_DEVICE_APPEARANCE=0
CONFIG_BT_ID_MAX=1
# CONFIG_BT_DF is not set
# CONFIG_BT_HOST_CCM is not set
# CONFIG_BT_LOG_SNIFFER_INFO is not set
# CONFIG_BT_TESTING is not set
# CONFIG_BT_CLASSIC is not set
# CONFIG_BT_HCI_VS_EVT_USER is not set
# end of BLE over nRF RPC
# end of Bluetooth Low Energy

#
# DFU
#
# CONFIG_DFU_MULTI_IMAGE is not set
# CONFIG_DFU_TARGET is not set
# end of DFU

# CONFIG_ESB is not set

#
# Peripheral CPU DFU (PCD)
#
# CONFIG_PCD is not set
# CONFIG_PCD_APP is not set
CONFIG_PCD_VERSION_PAGE_BUF_SIZE=2046
# CONFIG_PCD_NET is not set
# end of Peripheral CPU DFU (PCD)

#
# Networking
#

#
# Application protocols
#
# CONFIG_NRF_CLOUD is not set
# CONFIG_REST_CLIENT is not set
# CONFIG_DOWNLOADER is not set
# CONFIG_AWS_IOT is not set
# CONFIG_AWS_JOBS is not set
# CONFIG_AZURE_IOT_HUB is not set

#
# Self-Registration (Zi ZHu Ce)
#
# end of Self-Registration (Zi ZHu Ce)

# CONFIG_ICAL_PARSER is not set
# CONFIG_FTP_CLIENT is not set
# CONFIG_LWM2M_CLIENT_UTILS is not set
# CONFIG_MQTT_HELPER is not set
# CONFIG_NRF_MCUMGR_SMP_CLIENT is not set
# CONFIG_WIFI_PROV_CORE_LOG_LEVEL_OFF is not set
# CONFIG_WIFI_PROV_CORE_LOG_LEVEL_ERR is not set
# CONFIG_WIFI_PROV_CORE_LOG_LEVEL_WRN is not set
# CONFIG_WIFI_PROV_CORE_LOG_LEVEL_INF is not set
# CONFIG_WIFI_PROV_CORE_LOG_LEVEL_DBG is not set
CONFIG_WIFI_PROV_CORE_LOG_LEVEL_DEFAULT=y
CONFIG_WIFI_PROV_CORE_LOG_LEVEL=3
# end of Application protocols

# CONFIG_OPENTHREAD_RPC is not set
# end of Networking

#
# NFC
#
# CONFIG_NFC_NDEF is not set
# CONFIG_NFC_NDEF_PARSER is not set
# CONFIG_NFC_NDEF_PAYLOAD_TYPE_COMMON is not set
# CONFIG_NFC_T2T_PARSER is not set
# CONFIG_NFC_T4T_NDEF_FILE is not set
# CONFIG_NFC_T4T_ISODEP is not set
# CONFIG_NFC_T4T_APDU is not set
# CONFIG_NFC_T4T_CC_FILE is not set
# CONFIG_NFC_T4T_HL_PROCEDURE is not set
# CONFIG_NFC_TNEP_TAG is not set
# CONFIG_NFC_TNEP_POLLER is not set
# CONFIG_NFC_TNEP_CH is not set
# CONFIG_NFC_RPC is not set
# end of NFC

# CONFIG_APP_EVENT_MANAGER is not set
# CONFIG_NRF_PROFILER is not set
# CONFIG_FW_INFO is not set

#
# Debug
#
# CONFIG_NRF_CPU_LOAD is not set
# CONFIG_ETB_TRACE is not set
# CONFIG_PPI_TRACE is not set
CONFIG_PPI_TRACE_PIN_CNT=8
# end of Debug

# CONFIG_SHELL_BT_NUS is not set

#
# Multiprotocol service layer (MPSL)
#
# CONFIG_MPSL_FEM_ONLY is not set
# CONFIG_MPSL_FEM_DEVICE_CONFIG_254 is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_OFF is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_ERR is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_WRN is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_INF is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_DBG is not set
CONFIG_MPSL_FEM_LOG_LEVEL_DEFAULT=y
CONFIG_MPSL_FEM_LOG_LEVEL=3
CONFIG_MPSL_THREAD_COOP_PRIO=8
CONFIG_MPSL_TIMESLOT_SESSION_COUNT=0
# CONFIG_MPSL_ASSERT_HANDLER is not set
CONFIG_MPSL_HFCLK_LATENCY=1400
CONFIG_MPSL_INIT_PRIORITY=40
CONFIG_MPSL_FORCE_RRAM_ON_ALL_THE_TIME=y
# CONFIG_MPSL_LOG_LEVEL_OFF is not set
# CONFIG_MPSL_LOG_LEVEL_ERR is not set
# CONFIG_MPSL_LOG_LEVEL_WRN is not set
# CONFIG_MPSL_LOG_LEVEL_INF is not set
# CONFIG_MPSL_LOG_LEVEL_DBG is not set
CONFIG_MPSL_LOG_LEVEL_DEFAULT=y
CONFIG_MPSL_LOG_LEVEL=3
# end of Multiprotocol service layer (MPSL)

#
# Partition Manager
#
CONFIG_PARTITION_MANAGER_ENABLED=y
CONFIG_FLASH_MAP_CUSTOM=y
CONFIG_SRAM_SIZE=128
CONFIG_SRAM_BASE_ADDRESS=0x20020000

#
# Zephyr subsystem configurations
#
# end of Zephyr subsystem configurations

#
# NCS subsystem configurations
#
CONFIG_PM_EXTERNAL_FLASH_BASE=0
CONFIG_PM_EXTERNAL_FLASH_PATH=""
CONFIG_PM_EXTERNAL_FLASH_SIZE_BITS=0
# CONFIG_PM_OVERRIDE_EXTERNAL_DRIVER_CHECK is not set
CONFIG_PM_SRAM_BASE=0x20000000
CONFIG_PM_SRAM_SIZE=0x40000
# end of Partition Manager

#
# nRF RPC (Remote Procedure Call) library
#
# end of nRF RPC (Remote Procedure Call) library

#
# Full Modem Firmware Update Management(FMFU)
#
# end of Full Modem Firmware Update Management(FMFU)

#
# Additional MCUmgr configuration
#

#
# Additional MCUmgr group configuration
#

#
# Additional MCUmgr OS group management functionality
#
# end of Additional MCUmgr OS group management functionality

#
# Additional MCUmgr image management group functionality
#
# end of Additional MCUmgr image management group functionality
# end of Additional MCUmgr group configuration
# end of Additional MCUmgr configuration

# CONFIG_CAF is not set
# CONFIG_DM_MODULE is not set

#
# nRF Security
#
# CONFIG_NORDIC_SECURITY_BACKEND is not set
CONFIG_NRF_SECURITY=y

#
# Nordic-added meta types
#
CONFIG_PSA_HAS_CIPHER_SUPPORT=y
CONFIG_PSA_HAS_HASH_SUPPORT=y
CONFIG_PSA_HAS_KEY_DERIVATION=y
CONFIG_PSA_HAS_KEY_SUPPORT=y
CONFIG_PSA_HAS_MAC_SUPPORT=y

#
# Nordic added alg types
#
# CONFIG_PSA_WANT_ALG_ECDSA_ANY is not set
# CONFIG_PSA_WANT_ALG_ED25519PH is not set
# CONFIG_PSA_WANT_ALG_ED448PH is not set
# CONFIG_PSA_WANT_ALG_HSS is not set
# CONFIG_PSA_WANT_ALG_LMS is not set
# CONFIG_PSA_WANT_ALG_ML_DSA is not set
# CONFIG_PSA_WANT_ALG_XMSS is not set
# CONFIG_PSA_WANT_ALG_XMSS_MT is not set
# CONFIG_PSA_WANT_ALG_ML_KEM is not set
# CONFIG_PSA_WANT_ALG_PURE_EDDSA is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_SIGN_RAW is not set
# CONFIG_PSA_WANT_ALG_RSA_PSS_ANY_SALT is not set
# CONFIG_PSA_WANT_ALG_SHA_256_192 is not set
# CONFIG_PSA_WANT_ALG_SHA_512_224 is not set
# CONFIG_PSA_WANT_ALG_SHA_512_256 is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_HMAC is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_CMAC is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_MATTER is not set
# CONFIG_PSA_WANT_ALG_SP800_108_COUNTER_HMAC is not set
# CONFIG_PSA_WANT_ALG_SP800_108_COUNTER_CMAC is not set
# CONFIG_PSA_WANT_ALG_SRP_6 is not set
# CONFIG_PSA_WANT_ALG_SRP_PASSWORD_HASH is not set
# CONFIG_PSA_WANT_ALG_XTS is not set
CONFIG_PSA_WANT_ALG_ECB_NO_PADDING=y
# CONFIG_PSA_WANT_ALG_CHACHA20 is not set
# CONFIG_PSA_WANT_ALG_XCHACHA20_POLY1305 is not set
# CONFIG_PSA_WANT_ALG_SHAKE128_256 is not set
# CONFIG_PSA_WANT_ALG_SHAKE256_192 is not set
# CONFIG_PSA_WANT_ALG_SHAKE256_256 is not set
# CONFIG_PSA_WANT_ALG_SHAKE256_512 is not set
# CONFIG_PSA_WANT_ALG_AES_KW is not set
# CONFIG_PSA_WANT_ALG_AES_KWP is not set
# CONFIG_PSA_WANT_ALG_WPA3_SAE_H2E is not set
# CONFIG_PSA_WANT_ALG_WPA3_SAE is not set

#
# Nordic added ECC curve types
#
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_224 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_320 is not set
# CONFIG_PSA_WANT_ECC_TWISTED_EDWARDS_255 is not set
# CONFIG_PSA_WANT_ECC_TWISTED_EDWARDS_448 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_224 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_233 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_283 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_409 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_571 is not set

#
# Nordic addded RNG configuration
#
CONFIG_PSA_WANT_GENERATE_RANDOM=y

#
# Nordic added key types
#
# CONFIG_PSA_WANT_KEY_TYPE_PEPPER is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_WPA3_SAE_PT is not set
# CONFIG_PSA_WANT_KEY_TYPE_XCHACHA20 is not set
# CONFIG_PSA_WANT_KEY_TYPE_HSS_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_LMS_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_XMSS_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_XMSS_MT_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_ML_DSA_KEY_SIZE_44 is not set
# CONFIG_PSA_WANT_ML_DSA_KEY_SIZE_65 is not set
# CONFIG_PSA_WANT_ML_DSA_KEY_SIZE_87 is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_DSA_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_DSA_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_DSA_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_DSA_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_DSA_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_ML_KEM_KEY_SIZE_512 is not set
# CONFIG_PSA_WANT_ML_KEM_KEY_SIZE_768 is not set
# CONFIG_PSA_WANT_ML_KEM_KEY_SIZE_1024 is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_KEM_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_KEM_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_KEM_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_KEM_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_KEM_PUBLIC_KEY is not set
CONFIG_MBEDTLS_CFG_FILE="nrf-config.h"
CONFIG_MBEDTLS_PSA_CRYPTO_CONFIG=y
CONFIG_MBEDTLS_PSA_CRYPTO_CONFIG_FILE="nrf-psa-crypto-config.h"
CONFIG_MBEDTLS_PSA_CRYPTO_USER_CONFIG_FILE="nrf-psa-crypto-user-config.h"
CONFIG_MBEDTLS_PSA_CRYPTO_C=y
CONFIG_PSA_CORE_OBERON=y

#
# PSA Driver Support
#
CONFIG_MBEDTLS_PSA_CRYPTO_DRIVERS=y
CONFIG_MBEDTLS_PSA_CRYPTO_CLIENT=y
CONFIG_PSA_CRYPTO_DRIVER_OBERON=y
# CONFIG_PSA_CRYPTO_DRIVER_CC3XX is not set

#
# Choose DRBG algorithm
#
CONFIG_PSA_WANT_ALG_CTR_DRBG=y
# CONFIG_PSA_WANT_ALG_HMAC_DRBG is not set
CONFIG_PSA_USE_CTR_DRBG_DRIVER=y
# end of Choose DRBG algorithm

#
# CryptoCell PSA Driver Configuration
#
CONFIG_PSA_USE_CC3XX_CTR_DRBG_DRIVER=y
# end of CryptoCell PSA Driver Configuration

#
# CRACEN PSA Driver Configuration
#
# end of CRACEN PSA Driver Configuration

#
# AES key size configuration
#
CONFIG_PSA_WANT_AES_KEY_SIZE_128=y
CONFIG_PSA_WANT_AES_KEY_SIZE_192=y
CONFIG_PSA_WANT_AES_KEY_SIZE_256=y
# end of AES key size configuration

#
# RSA key size configuration
#
# CONFIG_PSA_WANT_RSA_KEY_SIZE_1024 is not set
# CONFIG_PSA_WANT_RSA_KEY_SIZE_1536 is not set
# CONFIG_PSA_WANT_RSA_KEY_SIZE_2048 is not set
# CONFIG_PSA_WANT_RSA_KEY_SIZE_3072 is not set
# CONFIG_PSA_WANT_RSA_KEY_SIZE_4096 is not set
# CONFIG_PSA_WANT_RSA_KEY_SIZE_6144 is not set
# CONFIG_PSA_WANT_RSA_KEY_SIZE_8192 is not set
CONFIG_PSA_MAX_RSA_KEY_BITS=0
# end of RSA key size configuration

CONFIG_PSA_ACCEL_GENERATE_RANDOM=y
CONFIG_PSA_NEED_CC3XX_CTR_DRBG_DRIVER=y
# CONFIG_CRACEN_LOG_LEVEL_OFF is not set
# CONFIG_CRACEN_LOG_LEVEL_ERR is not set
# CONFIG_CRACEN_LOG_LEVEL_WRN is not set
# CONFIG_CRACEN_LOG_LEVEL_INF is not set
# CONFIG_CRACEN_LOG_LEVEL_DBG is not set
CONFIG_CRACEN_LOG_LEVEL_DEFAULT=y
CONFIG_CRACEN_LOG_LEVEL=3
CONFIG_PSA_NEED_OBERON_ECB_NO_PADDING_AES=y
CONFIG_PSA_NEED_OBERON_CIPHER_DRIVER=y
CONFIG_PSA_NEED_OBERON_SHA_224=y
CONFIG_PSA_NEED_OBERON_SHA_256=y
CONFIG_PSA_NEED_OBERON_HASH_DRIVER=y
CONFIG_PSA_NEED_OBERON_HMAC=y
CONFIG_PSA_NEED_OBERON_CMAC=y
CONFIG_PSA_NEED_OBERON_MAC_DRIVER=y
CONFIG_PSA_NEED_OBERON_HKDF=y
CONFIG_PSA_NEED_OBERON_KEY_DERIVATION_DRIVER=y

#
# PSA API support
#
CONFIG_MBEDTLS_USE_PSA_CRYPTO=y
# CONFIG_MBEDTLS_PSA_STATIC_KEY_SLOTS is not set
CONFIG_PSA_CRYPTO_SYS_INIT=y
# end of PSA API support

CONFIG_MBEDTLS_PLATFORM_MEMORY=y
CONFIG_MBEDTLS_PLATFORM_C=y
CONFIG_MBEDTLS_MEMORY_C=y
CONFIG_MBEDTLS_MEMORY_BUFFER_ALLOC_C=y
CONFIG_MBEDTLS_THREADING_C=y
CONFIG_MBEDTLS_BASE64_C=y
CONFIG_MBEDTLS_OID_C=y
CONFIG_MBEDTLS_ASN1_WRITE_C=y
CONFIG_MBEDTLS_ASN1_PARSE_C=y
CONFIG_MBEDTLS_ENTROPY_HARDWARE_ALT=y
CONFIG_MBEDTLS_AES_SETKEY_ENC_ALT=y
CONFIG_MBEDTLS_AES_SETKEY_DEC_ALT=y
CONFIG_MBEDTLS_AES_ENCRYPT_ALT=y
CONFIG_MBEDTLS_AES_DECRYPT_ALT=y
CONFIG_MBEDTLS_CHACHA20_ALT=y
CONFIG_MBEDTLS_POLY1305_ALT=y
CONFIG_MBEDTLS_ECDH_GEN_PUBLIC_ALT=y
CONFIG_MBEDTLS_ECDH_COMPUTE_SHARED_ALT=y
CONFIG_MBEDTLS_ECDSA_GENKEY_ALT=y
CONFIG_MBEDTLS_ECDSA_SIGN_ALT=y
CONFIG_MBEDTLS_ECDSA_VERIFY_ALT=y
CONFIG_MBEDTLS_ECJPAKE_ALT=y
CONFIG_MBEDTLS_SHA1_ALT=y
CONFIG_MBEDTLS_SHA224_ALT=y
CONFIG_MBEDTLS_SHA256_ALT=y
CONFIG_MBEDTLS_ENTROPY_FORCE_SHA256=y
CONFIG_MBEDTLS_ENTROPY_MAX_SOURCES=1
CONFIG_MBEDTLS_NO_PLATFORM_ENTROPY=y
# CONFIG_NRF_SECURITY_ADVANCED is not set
CONFIG_OBERON_ONLY_PSA_ENABLED=y
CONFIG_OBERON_ONLY_ENABLED=y

#
# Legacy mbed TLS crypto APIs
#
CONFIG_MBEDTLS_MPI_WINDOW_SIZE=6
# CONFIG_MBEDTLS_CIPHER_C is not set
# CONFIG_MBEDTLS_PK_C is not set
# CONFIG_MBEDTLS_PEM_PARSE_C is not set
# CONFIG_MBEDTLS_PEM_WRITE_C is not set
# end of Legacy mbed TLS crypto APIs

#
# Zephyr legacy configurations
#
# CONFIG_MBEDTLS_KEY_EXCHANGE_ALL_ENABLED is not set
# CONFIG_MBEDTLS_KEY_EXCHANGE_SOME_PSK_ENABLED is not set
# CONFIG_MBEDTLS_ECP_ALL_ENABLED is not set
# CONFIG_MBEDTLS_CIPHER_ALL_ENABLED is not set
# CONFIG_MBEDTLS_MAC_ALL_ENABLED is not set
# CONFIG_MBEDTLS_MAC_MD5_ENABLED is not set
# CONFIG_MBEDTLS_HMAC_DRBG_ENABLED is not set
# CONFIG_MBEDTLS_CIPHER is not set
# CONFIG_MBEDTLS_MD is not set
# CONFIG_MBEDTLS_ENTROPY_ENABLED is not set
# CONFIG_MBEDTLS_GENPRIME_ENABLED is not set
# end of Zephyr legacy configurations

CONFIG_MBEDTLS_LIBRARY_NRF_SECURITY=y
# end of nRF Security

#
# Audio Modules
#
# CONFIG_AUDIO_MODULE_TEST is not set

#
# Log levels
#
# end of Log levels
# end of Audio Modules

#
# Audio Modules
#
# CONFIG_AUDIO_MODULE_TEMPLATE is not set
# end of Audio Modules

# CONFIG_UART_ASYNC_ADAPTER is not set

#
# Logging over RPC
#
# CONFIG_LOG_FORWARDER_RPC is not set
# CONFIG_LOG_BACKEND_RPC is not set
CONFIG_LOG_BACKED_RPC_CRASH_INFO_FILENAME_SIZE=1
# end of Logging over RPC

# CONFIG_DULT is not set
# CONFIG_NRF_COMPRESS is not set

#
# MCUboot IDs (informative only, do not change)
#
CONFIG_MCUBOOT_APPLICATION_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_NETWORK_CORE_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_WIFI_PATCHES_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_QSPI_XIP_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_MCUBOOT_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_EXTRA_1_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_EXTRA_2_IMAGE_NUMBER=-1
# end of MCUboot IDs (informative only, do not change)
# end of Subsystems

# CONFIG_WFA_QT_LOG_LEVEL_OFF is not set
# CONFIG_WFA_QT_LOG_LEVEL_ERR is not set
# CONFIG_WFA_QT_LOG_LEVEL_WRN is not set
# CONFIG_WFA_QT_LOG_LEVEL_INF is not set
# CONFIG_WFA_QT_LOG_LEVEL_DBG is not set
CONFIG_WFA_QT_LOG_LEVEL_DEFAULT=y
CONFIG_WFA_QT_LOG_LEVEL=3
# CONFIG_WFA_QT_CONTROL_APP is not set
CONFIG_WFA_QT_THREAD_STACK_SIZE=5200
CONFIG_WFA_QT_REBOOT_TIMEOUT_MS=1000
CONFIG_WFA_QT_DEFAULT_INTERFACE="wlan0"
CONFIG_WPAS_READY_TIMEOUT_MS=10000

#
# Libraries
#
# CONFIG_APP_JWT is not set

#
# Binary libraries
#
# end of Binary libraries

CONFIG_NRF_MODEM_LIB=y

#
# Memory configuration
#
CONFIG_NRF_MODEM_LIB_HEAP_SIZE=1024
CONFIG_NRF_MODEM_LIB_SHMEM_CTRL_SIZE=0x4e8
CONFIG_NRF_MODEM_LIB_SHMEM_TX_SIZE=8320
CONFIG_NRF_MODEM_LIB_SHMEM_RX_SIZE=8192
CONFIG_NRF_MODEM_LIB_SHMEM_TRACE_SIZE=0
CONFIG_NRF_MODEM_LIB_SENDMSG_BUF_SIZE=128
# CONFIG_NRF_MODEM_LIB_MEM_DIAG is not set
# end of Memory configuration

# CONFIG_NRF_MODEM_LIB_TRACE is not set
CONFIG_NRF_MODEM_LIB_ON_FAULT_DO_NOTHING=y
# CONFIG_NRF_MODEM_LIB_ON_FAULT_RESET_MODEM is not set
# CONFIG_NRF_MODEM_LIB_ON_FAULT_APPLICATION_SPECIFIC is not set
CONFIG_NRF_MODEM_LIB_CFUN_HOOKS=y
# CONFIG_NRF_MODEM_LIB_FAULT_STRERROR is not set

#
# Shell
#
# CONFIG_NRF_MODEM_LIB_SHELL_TRACE is not set
# end of Shell

CONFIG_NRF_MODEM_LIB_IPC_IRQ_PRIO=1
# CONFIG_NRF_MODEM_LIB_LOG_LEVEL_OFF is not set
# CONFIG_NRF_MODEM_LIB_LOG_LEVEL_ERR is not set
# CONFIG_NRF_MODEM_LIB_LOG_LEVEL_WRN is not set
# CONFIG_NRF_MODEM_LIB_LOG_LEVEL_INF is not set
# CONFIG_NRF_MODEM_LIB_LOG_LEVEL_DBG is not set
CONFIG_NRF_MODEM_LIB_LOG_LEVEL_DEFAULT=y
CONFIG_NRF_MODEM_LIB_LOG_LEVEL=3
# CONFIG_NRF_MODEM_LIB_LOG_FW_VERSION_UUID is not set
# CONFIG_AT_MONITOR is not set
# CONFIG_LTE_LINK_CONTROL is not set
# CONFIG_NTN is not set
CONFIG_NRF_SPU_FLASH_REGION_SIZE=0x8000
CONFIG_FPROTECT_BLOCK_SIZE=0x8000
# CONFIG_FPROTECT is not set
# CONFIG_AT_CMD_CUSTOM is not set
# CONFIG_AT_HOST_LIBRARY is not set
# CONFIG_DK_LIBRARY is not set
# CONFIG_AT_PARSER is not set
# CONFIG_MODEM_INFO is not set
# CONFIG_RESET_ON_FATAL_ERROR is not set
# CONFIG_SMS is not set
# CONFIG_GCF_SMS is not set
# CONFIG_MODEM_KEY_MGMT is not set
# CONFIG_SUPL_CLIENT_LIB is not set
# CONFIG_DATE_TIME is not set
# CONFIG_HW_ID_LIBRARY is not set
# CONFIG_WAVE_GEN_LIB is not set
CONFIG_HW_UNIQUE_KEY_SUPPORTED=y
CONFIG_HW_UNIQUE_KEY=y
CONFIG_HW_UNIQUE_KEY_RANDOM=y
CONFIG_HW_UNIQUE_KEY_PARTITION_SIZE=0
# CONFIG_MODEM_JWT is not set
# CONFIG_MODEM_ATTEST_TOKEN is not set
# CONFIG_LOCATION is not set
CONFIG_MODEM_ANTENNA=y
CONFIG_MODEM_ANTENNA_GNSS_ONBOARD=y
# CONFIG_MODEM_ANTENNA_GNSS_EXTERNAL is not set
CONFIG_MODEM_ANTENNA_AT_MAGPIO=""
CONFIG_MODEM_ANTENNA_AT_COEX0="AT%XCOEX0=1,1,1565,1586"
CONFIG_MODEM_ANTENNA_AT_MIPIRFFEDEV=""
CONFIG_MODEM_ANTENNA_AT_MIPIRFFECTRL_INIT=""
CONFIG_MODEM_ANTENNA_AT_MIPIRFFECTRL_ON=""
CONFIG_MODEM_ANTENNA_AT_MIPIRFFECTRL_OFF=""
CONFIG_MODEM_ANTENNA_AT_MIPIRFFECTRL_PWROFF=""
# CONFIG_MODEM_ANTENNA_LOG_LEVEL_OFF is not set
# CONFIG_MODEM_ANTENNA_LOG_LEVEL_ERR is not set
# CONFIG_MODEM_ANTENNA_LOG_LEVEL_WRN is not set
# CONFIG_MODEM_ANTENNA_LOG_LEVEL_INF is not set
# CONFIG_MODEM_ANTENNA_LOG_LEVEL_DBG is not set
CONFIG_MODEM_ANTENNA_LOG_LEVEL_DEFAULT=y
CONFIG_MODEM_ANTENNA_LOG_LEVEL=3
# CONFIG_QOS is not set
# CONFIG_IDENTITY_KEY_TFM is not set
# CONFIG_SFLOAT is not set
# CONFIG_CONTIN_ARRAY is not set
# CONFIG_PCM_MIX is not set
# CONFIG_TONE is not set
# CONFIG_PSCM is not set
# CONFIG_DATA_FIFO is not set
# CONFIG_FEM_AL_LIB is not set
# CONFIG_SAMPLE_RATE_CONVERTER is not set
CONFIG_NCS_BOOT_BANNER=y
CONFIG_NCS_NCS_BOOT_BANNER_STRING="nRF Connect SDK"
CONFIG_NCS_ZEPHYR_BOOT_BANNER_STRING="Zephyr OS"
# CONFIG_UICC_LWM2M is not set
# end of Libraries

#
# Device Drivers
#
# CONFIG_BT_DRIVER_QUIRK_NO_AUTO_DLE is not set
# CONFIG_FLASH_RPC is not set
CONFIG_SOC_FLASH_NRF_RADIO_SYNC_MPSL_TIMESLOT_SESSION_COUNT=0
# CONFIG_ETH_RTT is not set
# CONFIG_SENSOR is not set
CONFIG_NRF_SW_LPUART=y
CONFIG_NRFX_GPIOTE_NUM_OF_EVT_HANDLERS=2
CONFIG_NRF_SW_LPUART_INIT_PRIORITY=45
CONFIG_NRF_SW_LPUART_HFXO_ON_RX=y
CONFIG_NRF_SW_LPUART_MAX_PACKET_SIZE=128
CONFIG_NRF_SW_LPUART_DEFAULT_TX_TIMEOUT=1000000
CONFIG_NRF_SW_LPUART_INT_DRIVEN=y
CONFIG_NRF_SW_LPUART_INT_DRV_TX_BUF_SIZE=128
# CONFIG_NRF_SW_LPUART_LOG_LEVEL_OFF is not set
# CONFIG_NRF_SW_LPUART_LOG_LEVEL_ERR is not set
# CONFIG_NRF_SW_LPUART_LOG_LEVEL_WRN is not set
# CONFIG_NRF_SW_LPUART_LOG_LEVEL_INF is not set
# CONFIG_NRF_SW_LPUART_LOG_LEVEL_DBG is not set
CONFIG_NRF_SW_LPUART_LOG_LEVEL_DEFAULT=y
CONFIG_NRF_SW_LPUART_LOG_LEVEL=3
# end of Device Drivers

#
# External libraries
#
# end of External libraries

#
# Test
#
# CONFIG_UNITY is not set

#
# Mocks
#
# CONFIG_MOCK_NRF_MODEM_AT is not set
# CONFIG_MOCK_NRF_RPC is not set
# end of Mocks
# end of Test
# end of Nordic nRF Connect

CONFIG_ZEPHYR_NRF_MODULE=y
# end of nrf (/opt/nordic/ncs/v3.1.1/nrf)

#
# hostap (/opt/nordic/ncs/v3.1.1/modules/lib/hostap)
#
# CONFIG_WIFI_NM_WPA_SUPPLICANT is not set
CONFIG_ZEPHYR_HOSTAP_MODULE=y
# end of hostap (/opt/nordic/ncs/v3.1.1/modules/lib/hostap)

#
# mcuboot (/opt/nordic/ncs/v3.1.1/bootloader/mcuboot)
#

#
# MCUboot
#
CONFIG_DT_FLASH_WRITE_BLOCK_SIZE=4
# CONFIG_USE_NRF53_MULTI_IMAGE_WITHOUT_UPGRADE_ONLY is not set
# CONFIG_MCUBOOT_USE_ALL_AVAILABLE_RAM is not set
# end of MCUboot

CONFIG_ZEPHYR_MCUBOOT_MODULE=y
# end of mcuboot (/opt/nordic/ncs/v3.1.1/bootloader/mcuboot)

#
# mbedtls (/opt/nordic/ncs/v3.1.1/modules/crypto/mbedtls)
#
CONFIG_ZEPHYR_MBEDTLS_MODULE=y
CONFIG_PSA_CRYPTO_CLIENT=y
# CONFIG_PSA_CRYPTO_ENABLE_ALL is not set
# CONFIG_PSA_WANT_ALG_CBC_NO_PADDING is not set
# CONFIG_PSA_WANT_ALG_CBC_PKCS7 is not set
# CONFIG_PSA_WANT_ALG_CCM is not set
# CONFIG_PSA_WANT_ALG_CCM_STAR_NO_TAG is not set
CONFIG_PSA_WANT_ALG_CMAC=y
# CONFIG_PSA_WANT_ALG_CHACHA20_POLY1305 is not set
# CONFIG_PSA_WANT_ALG_CTR is not set
# CONFIG_PSA_WANT_ALG_DETERMINISTIC_ECDSA is not set
# CONFIG_PSA_WANT_ALG_ECDH is not set
# CONFIG_PSA_WANT_ALG_ECDSA is not set
# CONFIG_PSA_WANT_ALG_JPAKE is not set
# CONFIG_PSA_WANT_ALG_GCM is not set
CONFIG_PSA_WANT_ALG_HKDF=y
# CONFIG_PSA_WANT_ALG_HKDF_EXTRACT is not set
# CONFIG_PSA_WANT_ALG_HKDF_EXPAND is not set
CONFIG_PSA_WANT_ALG_HMAC=y
# CONFIG_PSA_WANT_ALG_MD5 is not set
# CONFIG_PSA_WANT_ALG_PBKDF2_HMAC is not set
# CONFIG_PSA_WANT_ALG_PBKDF2_AES_CMAC_PRF_128 is not set
# CONFIG_PSA_WANT_ALG_RSA_OAEP is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_CRYPT is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_SIGN is not set
# CONFIG_PSA_WANT_ALG_RSA_PSS is not set
# CONFIG_PSA_WANT_ALG_SHA_1 is not set
CONFIG_PSA_WANT_ALG_SHA_224=y
CONFIG_PSA_WANT_ALG_SHA_256=y
# CONFIG_PSA_WANT_ALG_SHA_384 is not set
# CONFIG_PSA_WANT_ALG_SHA_512 is not set
# CONFIG_PSA_WANT_ALG_SHA3_224 is not set
# CONFIG_PSA_WANT_ALG_SHA3_256 is not set
# CONFIG_PSA_WANT_ALG_SHA3_384 is not set
# CONFIG_PSA_WANT_ALG_SHA3_512 is not set
# CONFIG_PSA_WANT_ALG_STREAM_CIPHER is not set
# CONFIG_PSA_WANT_ALG_TLS12_PRF is not set
# CONFIG_PSA_WANT_ALG_TLS12_PSK_TO_MS is not set
# CONFIG_PSA_WANT_ALG_TLS12_ECJPAKE_TO_PMS is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_256 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_384 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_512 is not set
# CONFIG_PSA_WANT_ECC_MONTGOMERY_255 is not set
# CONFIG_PSA_WANT_ECC_MONTGOMERY_448 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_192 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_256 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_192 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_224 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_256 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_384 is not set
# CONFIG_PSA_WANT_ECC_SECP_R1_521 is not set
# CONFIG_PSA_WANT_KEY_TYPE_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_PASSWORD is not set
# CONFIG_PSA_WANT_KEY_TYPE_PASSWORD_HASH is not set
# CONFIG_PSA_WANT_KEY_TYPE_HMAC is not set
CONFIG_PSA_WANT_KEY_TYPE_AES=y
# CONFIG_PSA_WANT_KEY_TYPE_ECC_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_RAW_DATA is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ECC_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_RSA_KEY_PAIR_DERIVE is not set
CONFIG_PSA_CRYPTO=y
CONFIG_PSA_CRYPTO_PROVIDER_TFM=y
# CONFIG_MBEDTLS_LIBRARY is not set
CONFIG_DISABLE_MBEDTLS_BUILTIN=y
# CONFIG_CUSTOM_MBEDTLS_CFG_FILE is not set
# CONFIG_MBEDTLS_LOG_LEVEL_OFF is not set
# CONFIG_MBEDTLS_LOG_LEVEL_ERR is not set
# CONFIG_MBEDTLS_LOG_LEVEL_WRN is not set
# CONFIG_MBEDTLS_LOG_LEVEL_INF is not set
# CONFIG_MBEDTLS_LOG_LEVEL_DBG is not set
CONFIG_MBEDTLS_LOG_LEVEL_DEFAULT=y
CONFIG_MBEDTLS_LOG_LEVEL=3
# CONFIG_MBEDTLS_DEBUG is not set
# CONFIG_MBEDTLS_HEAP_CUSTOM_SECTION is not set
CONFIG_MBEDTLS_INIT=y
# CONFIG_MBEDTLS_ZEROIZE_ALT is not set
CONFIG_APP_LINK_WITH_MBEDTLS=y
# end of mbedtls (/opt/nordic/ncs/v3.1.1/modules/crypto/mbedtls)

#
# oberon-psa-crypto (/opt/nordic/ncs/v3.1.1/modules/crypto/oberon-psa-crypto)
#
CONFIG_ZEPHYR_OBERON_PSA_CRYPTO_MODULE=y
# end of oberon-psa-crypto (/opt/nordic/ncs/v3.1.1/modules/crypto/oberon-psa-crypto)

#
# trusted-firmware-m (/opt/nordic/ncs/v3.1.1/modules/tee/tf-m/trusted-firmware-m)
#
CONFIG_TFM_BOARD="/opt/nordic/ncs/v3.1.1/nrf/modules/trusted-firmware-m/tfm_boards/nrf9120"
# CONFIG_TFM_DUMMY_PROVISIONING is not set
# CONFIG_TFM_REGRESSION_NS is not set
CONFIG_TFM_LOG_LEVEL_SILENCE=y
CONFIG_TFM_QCBOR_PATH="/opt/nordic/ncs/v3.1.1/modules/tee/tf-m/trusted-firmware-m/../qcbor"
# CONFIG_TFM_PARTITION_PROTECTED_STORAGE is not set
CONFIG_ZEPHYR_TRUSTED_FIRMWARE_M_MODULE=y
CONFIG_TFM_PROFILE_TYPE_NOT_SET=y
# CONFIG_TFM_PROFILE_TYPE_SMALL is not set
# CONFIG_TFM_PROFILE_TYPE_MEDIUM is not set
# CONFIG_TFM_PROFILE_TYPE_AROTLESS is not set
# CONFIG_TFM_PROFILE_TYPE_LARGE is not set
# CONFIG_TFM_CMAKE_BUILD_TYPE_RELEASE is not set
# CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO is not set
# CONFIG_TFM_CMAKE_BUILD_TYPE_MINSIZEREL is not set
CONFIG_TFM_CMAKE_BUILD_TYPE_DEBUG=y
CONFIG_TFM_ISOLATION_LEVEL=1
# CONFIG_TFM_ITS_NUM_ASSETS_OVERRIDE is not set
CONFIG_TFM_ITS_NUM_ASSETS=10
# CONFIG_TFM_ITS_MAX_ASSET_SIZE_OVERRIDE is not set
CONFIG_TFM_ITS_MAX_ASSET_SIZE=512
CONFIG_TFM_PARTITION_PLATFORM_CUSTOM_REBOOT=y
CONFIG_TFM_BL2_NOT_SUPPORTED=y
CONFIG_TFM_IMAGE_VERSION_S="0.0.0+0"
CONFIG_TFM_IMAGE_VERSION_NS="0.0.0+0"
# CONFIG_TFM_BL1 is not set
# CONFIG_TFM_USE_NS_APP is not set
# CONFIG_TFM_CONNECTION_BASED_SERVICE_API is not set
CONFIG_TFM_IPC=y
# CONFIG_TFM_SFN is not set
# CONFIG_TFM_REGRESSION_S is not set
# CONFIG_TFM_PSA_TEST_CRYPTO is not set
# CONFIG_TFM_PSA_TEST_PROTECTED_STORAGE is not set
# CONFIG_TFM_PSA_TEST_INTERNAL_TRUSTED_STORAGE is not set
# CONFIG_TFM_PSA_TEST_STORAGE is not set
# CONFIG_TFM_PSA_TEST_INITIAL_ATTESTATION is not set
CONFIG_TFM_PSA_TEST_NONE=y
CONFIG_TFM_FLASH_MERGED_BINARY=y
CONFIG_TFM_EXCEPTION_INFO_DUMP=y
CONFIG_TFM_PARTITION_INTERNAL_TRUSTED_STORAGE=y
# CONFIG_TFM_PARTITION_FIRMWARE_UPDATE is not set
CONFIG_TFM_CRYPTO_KEY_MODULE_ENABLED=y
CONFIG_TFM_CRYPTO_MAC_MODULE_ENABLED=y
CONFIG_TFM_CRYPTO_HASH_MODULE_ENABLED=y
CONFIG_TFM_CRYPTO_CIPHER_MODULE_ENABLED=y
CONFIG_TFM_CRYPTO_KEY_DERIVATION_MODULE_ENABLED=y

#
# Platform partition component configs
#
CONFIG_TFM_PLATFORM_SERVICE_INPUT_BUFFER_SIZE=64
CONFIG_TFM_PLATFORM_SERVICE_OUTPUT_BUFFER_SIZE=64
CONFIG_TFM_PLATFORM_SP_STACK_SIZE=0x500
CONFIG_TFM_PLATFORM_NV_COUNTER_MODULE_DISABLED=y
# end of Platform partition component configs

#
# Crypto component configs
#
# CONFIG_TFM_CRYPTO_SINGLE_PART_FUNCS_DISABLED is not set
CONFIG_TFM_CRYPTO_BUILTIN_KEYS=y
CONFIG_TFM_CRYPTO_ENGINE_BUF_SIZE=8320
CONFIG_TFM_CRYPTO_CONC_OPER_NUM=8
CONFIG_TFM_CRYPTO_IOVEC_BUFFER_SIZE=5120
CONFIG_TFM_CRYPTO_PARTITION_STACK_SIZE=0x2000
# end of Crypto component configs

#
# ITS component configs
#
CONFIG_TFM_ITS_CREATE_FLASH_LAYOUT=y
# CONFIG_TFM_ITS_RAM_FS is not set
CONFIG_TFM_ITS_VALIDATE_METADATA_FROM_FLASH=y
CONFIG_TFM_ITS_BUF_SIZE=512
CONFIG_TFM_ITS_STACK_SIZE=0x720
# CONFIG_TFM_ITS_ENCRYPTED is not set
# end of ITS component configs

#
# TF-M SPM component configs
#
CONFIG_TFM_CONN_HANDLE_MAX_NUM=8
# CONFIG_TFM_DOORBELL_API is not set
# end of TF-M SPM component configs

#
# TF-M memory regions
#
CONFIG_PM_PARTITION_SIZE_TFM_SRAM=0x16000
CONFIG_PM_PARTITION_SIZE_TFM=0x50000
CONFIG_PM_PARTITION_SIZE_TFM_PROTECTED_STORAGE=0
CONFIG_PM_PARTITION_SIZE_TFM_INTERNAL_TRUSTED_STORAGE=0x2000
CONFIG_PM_PARTITION_SIZE_TFM_OTP_NV_COUNTERS=0
CONFIG_PM_PARTITION_TFM_STORAGE=y
# end of TF-M memory regions

#
# Peripheral Secure mapping
#
# CONFIG_NRF_FPU_SECURE is not set
# CONFIG_NRF_CLOCK_SECURE is not set
# CONFIG_NRF_POWER_SECURE is not set
# CONFIG_NRF_SPIM0_SECURE is not set
# CONFIG_NRF_TWIM0_SECURE is not set
# CONFIG_NRF_UARTE0_SECURE is not set
# CONFIG_NRF_SPIM1_SECURE is not set
# CONFIG_NRF_TWIM1_SECURE is not set
# CONFIG_NRF_UARTE1_SECURE is not set
# CONFIG_NRF_SPIM2_SECURE is not set
# CONFIG_NRF_TWIM2_SECURE is not set
# CONFIG_NRF_UARTE2_SECURE is not set
# CONFIG_NRF_SPIM3_SECURE is not set
# CONFIG_NRF_TWIM3_SECURE is not set
# CONFIG_NRF_UARTE3_SECURE is not set
# CONFIG_NRF_SAADC_SECURE is not set
# CONFIG_NRF_TIMER0_SECURE is not set
# CONFIG_NRF_TIMER1_SECURE is not set
# CONFIG_NRF_TIMER2_SECURE is not set
# CONFIG_NRF_RTC0_SECURE is not set
# CONFIG_NRF_RTC1_SECURE is not set
# CONFIG_NRF_DPPI_SECURE is not set
# CONFIG_NRF_WDT0_SECURE is not set
# CONFIG_NRF_EGU0_SECURE is not set
# CONFIG_NRF_EGU1_SECURE is not set
# CONFIG_NRF_EGU2_SECURE is not set
# CONFIG_NRF_EGU3_SECURE is not set
# CONFIG_NRF_EGU4_SECURE is not set
# CONFIG_NRF_EGU5_SECURE is not set
# CONFIG_NRF_PWM0_SECURE is not set
# CONFIG_NRF_PWM1_SECURE is not set
# CONFIG_NRF_PWM2_SECURE is not set
# CONFIG_NRF_PWM3_SECURE is not set
# CONFIG_NRF_PDM_SECURE is not set
# CONFIG_NRF_I2S_SECURE is not set
# CONFIG_NRF_IPC_SECURE is not set
# CONFIG_NRF_NVMC_SECURE is not set
# CONFIG_NRF_GPIO0_SECURE is not set
# CONFIG_NRF_GPIOTE0_SECURE is not set
CONFIG_NRF_GPIO0_PIN_MASK_SECURE=0x00000000
CONFIG_NRF_DPPI_CHANNEL_MASK_SECURE=0x00000000
CONFIG_NRF_VMC_SECURE=y
# end of Peripheral Secure mapping

# CONFIG_TFM_PROFILE_TYPE_MINIMAL is not set
CONFIG_TFM_CPU_FREQ_MHZ=128
# CONFIG_TFM_SECURE_UART is not set
CONFIG_TFM_EXPERIMENTAL=y
# CONFIG_TFM_HW_INIT_RESET_ON_BOOT is not set
CONFIG_TFM_HALT_ON_CORE_PANIC=y
CONFIG_TFM_ALLOW_NON_SECURE_RESET=y
CONFIG_TFM_ALLOW_NON_SECURE_FAULT_HANDLING=y
CONFIG_TFM_S_CODE_VECTOR_TABLE_SIZE=0x144
# CONFIG_TFM_PSA_FRAMEWORK_HAS_MM_IOVEC is not set
# end of trusted-firmware-m (/opt/nordic/ncs/v3.1.1/modules/tee/tf-m/trusted-firmware-m)

CONFIG_ZEPHYR_PSA_ARCH_TESTS_MODULE=y

#
# cjson (/opt/nordic/ncs/v3.1.1/modules/lib/cjson)
#
# CONFIG_CJSON_LIB is not set
CONFIG_ZEPHYR_CJSON_MODULE=y
# end of cjson (/opt/nordic/ncs/v3.1.1/modules/lib/cjson)

#
# azure-sdk-for-c (/opt/nordic/ncs/v3.1.1/modules/lib/azure-sdk-for-c)
#
# CONFIG_AZURE_SDK is not set
CONFIG_ZEPHYR_AZURE_SDK_FOR_C_MODULE=y
# end of azure-sdk-for-c (/opt/nordic/ncs/v3.1.1/modules/lib/azure-sdk-for-c)

#
# cirrus-logic (/opt/nordic/ncs/v3.1.1/modules/hal/cirrus-logic)
#
# CONFIG_HW_CODEC_CIRRUS_LOGIC is not set
CONFIG_ZEPHYR_CIRRUS_LOGIC_MODULE=y
# end of cirrus-logic (/opt/nordic/ncs/v3.1.1/modules/hal/cirrus-logic)

#
# openthread (/opt/nordic/ncs/v3.1.1/modules/lib/openthread)
#
# CONFIG_OPENTHREAD is not set
CONFIG_ZEPHYR_OPENTHREAD_MODULE=y
# end of openthread (/opt/nordic/ncs/v3.1.1/modules/lib/openthread)

#
# memfault-firmware-sdk (/opt/nordic/ncs/v3.1.1/modules/lib/memfault-firmware-sdk)
#
# CONFIG_MEMFAULT is not set
CONFIG_ZEPHYR_MEMFAULT_FIRMWARE_SDK_MODULE=y
# end of memfault-firmware-sdk (/opt/nordic/ncs/v3.1.1/modules/lib/memfault-firmware-sdk)

#
# coremark (/opt/nordic/ncs/v3.1.1/modules/benchmark/coremark)
#
# CONFIG_COREMARK is not set
CONFIG_ZEPHYR_COREMARK_MODULE=y
# end of coremark (/opt/nordic/ncs/v3.1.1/modules/benchmark/coremark)

#
# canopennode (/opt/nordic/ncs/v3.1.1/modules/lib/canopennode)
#
CONFIG_ZEPHYR_CANOPENNODE_MODULE=y
# end of canopennode (/opt/nordic/ncs/v3.1.1/modules/lib/canopennode)

#
# chre (/opt/nordic/ncs/v3.1.1/modules/lib/chre)
#
CONFIG_ZEPHYR_CHRE_MODULE=y
# CONFIG_CHRE is not set
# end of chre (/opt/nordic/ncs/v3.1.1/modules/lib/chre)

#
# lz4 (/opt/nordic/ncs/v3.1.1/modules/lib/lz4)
#
CONFIG_ZEPHYR_LZ4_MODULE=y
# CONFIG_LZ4 is not set
# end of lz4 (/opt/nordic/ncs/v3.1.1/modules/lib/lz4)

CONFIG_ZEPHYR_TF_M_TESTS_MODULE=y

#
# zscilib (/opt/nordic/ncs/v3.1.1/modules/lib/zscilib)
#
# CONFIG_ZSL is not set
CONFIG_ZEPHYR_ZSCILIB_MODULE=y
# end of zscilib (/opt/nordic/ncs/v3.1.1/modules/lib/zscilib)

#
# cmsis (/opt/nordic/ncs/v3.1.1/modules/hal/cmsis)
#
CONFIG_ZEPHYR_CMSIS_MODULE=y
CONFIG_HAS_CMSIS_CORE=y
# end of cmsis (/opt/nordic/ncs/v3.1.1/modules/hal/cmsis)

#
# cmsis-dsp (/opt/nordic/ncs/v3.1.1/modules/lib/cmsis-dsp)
#
CONFIG_ZEPHYR_CMSIS_DSP_MODULE=y
# CONFIG_CMSIS_DSP is not set
# end of cmsis-dsp (/opt/nordic/ncs/v3.1.1/modules/lib/cmsis-dsp)

#
# cmsis-nn (/opt/nordic/ncs/v3.1.1/modules/lib/cmsis-nn)
#
CONFIG_ZEPHYR_CMSIS_NN_MODULE=y
# CONFIG_CMSIS_NN is not set
# end of cmsis-nn (/opt/nordic/ncs/v3.1.1/modules/lib/cmsis-nn)

#
# cmsis_6 (/opt/nordic/ncs/v3.1.1/modules/hal/cmsis_6)
#
CONFIG_ZEPHYR_CMSIS_6_MODULE=y
CONFIG_HAS_CMSIS_CORE_M=y
# CONFIG_CMSIS_M_CHECK_DEVICE_DEFINES is not set
# end of cmsis_6 (/opt/nordic/ncs/v3.1.1/modules/hal/cmsis_6)

#
# fatfs (/opt/nordic/ncs/v3.1.1/modules/fs/fatfs)
#
CONFIG_ZEPHYR_FATFS_MODULE=y
# end of fatfs (/opt/nordic/ncs/v3.1.1/modules/fs/fatfs)

#
# hal_nordic (/opt/nordic/ncs/v3.1.1/modules/hal/nordic)
#
CONFIG_ZEPHYR_HAL_NORDIC_MODULE=y
# CONFIG_NRF_802154_SOURCE_HAL_NORDIC is not set
CONFIG_HAS_NRFX=y

#
# nrfx drivers
#

#
# nrfx drivers logging
#
# CONFIG_NRFX_CLOCK_LOG is not set
# CONFIG_NRFX_GPIOTE_LOG is not set
# CONFIG_NRFX_IPC_LOG is not set
# CONFIG_NRFX_NVMC_LOG is not set
# CONFIG_NRFX_TIMER_LOG is not set
# end of nrfx drivers logging

CONFIG_NRFX_CLOCK=y
# CONFIG_NRFX_CLOCK_USE_LFRC_CALIBRATION is not set
CONFIG_NRFX_CLOCK_LFXO_TWO_STAGE_ENABLED=y
# CONFIG_NRFX_CLOCK_LF_CAL_ENABLED is not set
# CONFIG_NRFX_CLOCK_LF_SRC_RC is not set
CONFIG_NRFX_CLOCK_LF_SRC_XTAL=y
# CONFIG_NRFX_EGU0 is not set
# CONFIG_NRFX_EGU1 is not set
# CONFIG_NRFX_EGU2 is not set
# CONFIG_NRFX_EGU3 is not set
# CONFIG_NRFX_EGU4 is not set
# CONFIG_NRFX_EGU5 is not set
CONFIG_NRFX_GPIOTE=y
CONFIG_NRFX_GPIOTE1=y
CONFIG_NRFX_GPPI=y
# CONFIG_NRFX_GPPI_V1 is not set
# CONFIG_NRFX_I2S is not set
CONFIG_NRFX_IPC=y
CONFIG_NRFX_NVMC=y
# CONFIG_NRFX_PDM is not set
# CONFIG_NRFX_POWER is not set
# CONFIG_NRFX_PWM is not set
# CONFIG_NRFX_QDEC is not set
# CONFIG_NRFX_RTC0 is not set
# CONFIG_NRFX_RTC1 is not set
# CONFIG_NRFX_SAADC is not set
# CONFIG_NRFX_SPIM is not set
# CONFIG_NRFX_SYSTICK is not set
CONFIG_NRFX_TIMER=y
# CONFIG_NRFX_TWIM is not set
# CONFIG_NRFX_TWIS is not set
# CONFIG_NRFX_UARTE is not set

#
# Peripheral Resource Sharing module
#
# CONFIG_NRFX_PRS_BOX_0 is not set
# CONFIG_NRFX_PRS_BOX_1 is not set
# CONFIG_NRFX_PRS_BOX_2 is not set
# CONFIG_NRFX_PRS_BOX_3 is not set
# CONFIG_NRFX_PRS_BOX_4 is not set
# end of Peripheral Resource Sharing module

CONFIG_NRFX_RESERVED_RESOURCES_HEADER="nrfx_reserved_resources_ncs.h"
# end of nrfx drivers
# end of hal_nordic (/opt/nordic/ncs/v3.1.1/modules/hal/nordic)

#
# hal_st (/opt/nordic/ncs/v3.1.1/modules/hal/st)
#
CONFIG_ZEPHYR_HAL_ST_MODULE=y
# end of hal_st (/opt/nordic/ncs/v3.1.1/modules/hal/st)

#
# hal_tdk (/opt/nordic/ncs/v3.1.1/modules/hal/tdk)
#
CONFIG_ZEPHYR_HAL_TDK_MODULE=y

#
# TDK drivers
#
# CONFIG_TDK_HAL is not set
# end of TDK drivers
# end of hal_tdk (/opt/nordic/ncs/v3.1.1/modules/hal/tdk)

CONFIG_ZEPHYR_HAL_WURTHELEKTRONIK_MODULE=y

#
# liblc3 (/opt/nordic/ncs/v3.1.1/modules/lib/liblc3)
#
CONFIG_ZEPHYR_LIBLC3_MODULE=y
# end of liblc3 (/opt/nordic/ncs/v3.1.1/modules/lib/liblc3)

CONFIG_ZEPHYR_LIBMETAL_MODULE=y

#
# littlefs (/opt/nordic/ncs/v3.1.1/modules/fs/littlefs)
#
CONFIG_ZEPHYR_LITTLEFS_MODULE=y
# end of littlefs (/opt/nordic/ncs/v3.1.1/modules/fs/littlefs)

#
# loramac-node (/opt/nordic/ncs/v3.1.1/modules/lib/loramac-node)
#
CONFIG_ZEPHYR_LORAMAC_NODE_MODULE=y
# CONFIG_HAS_SEMTECH_RADIO_DRIVERS is not set
# end of loramac-node (/opt/nordic/ncs/v3.1.1/modules/lib/loramac-node)

#
# lvgl (/opt/nordic/ncs/v3.1.1/modules/lib/gui/lvgl)
#
CONFIG_ZEPHYR_LVGL_MODULE=y
# end of lvgl (/opt/nordic/ncs/v3.1.1/modules/lib/gui/lvgl)

CONFIG_ZEPHYR_MIPI_SYS_T_MODULE=y

#
# nanopb (/opt/nordic/ncs/v3.1.1/modules/lib/nanopb)
#
CONFIG_ZEPHYR_NANOPB_MODULE=y
# CONFIG_NANOPB is not set
# end of nanopb (/opt/nordic/ncs/v3.1.1/modules/lib/nanopb)

#
# nrf_wifi (/opt/nordic/ncs/v3.1.1/modules/lib/nrf_wifi)
#
CONFIG_ZEPHYR_NRF_WIFI_MODULE=y
# CONFIG_NRF70_BUSLIB is not set
# end of nrf_wifi (/opt/nordic/ncs/v3.1.1/modules/lib/nrf_wifi)

CONFIG_ZEPHYR_OPEN_AMP_MODULE=y

#
# percepio (/opt/nordic/ncs/v3.1.1/modules/debug/percepio)
#

#
# Percepio Tracealyzer support can be enabled from the tracing subsystem
#
# CONFIG_PERCEPIO_DFM is not set
CONFIG_ZEPHYR_PERCEPIO_MODULE=y
# end of percepio (/opt/nordic/ncs/v3.1.1/modules/debug/percepio)

#
# picolibc (/opt/nordic/ncs/v3.1.1/modules/lib/picolibc)
#
# CONFIG_PICOLIBC_MODULE is not set
CONFIG_ZEPHYR_PICOLIBC_MODULE=y
# end of picolibc (/opt/nordic/ncs/v3.1.1/modules/lib/picolibc)

#
# segger (/opt/nordic/ncs/v3.1.1/modules/debug/segger)
#
CONFIG_ZEPHYR_SEGGER_MODULE=y
CONFIG_HAS_SEGGER_RTT=y
# CONFIG_USE_SEGGER_RTT is not set
# end of segger (/opt/nordic/ncs/v3.1.1/modules/debug/segger)

#
# uoscore-uedhoc (/opt/nordic/ncs/v3.1.1/modules/lib/uoscore-uedhoc)
#
CONFIG_ZEPHYR_UOSCORE_UEDHOC_MODULE=y
# end of uoscore-uedhoc (/opt/nordic/ncs/v3.1.1/modules/lib/uoscore-uedhoc)

#
# zcbor (/opt/nordic/ncs/v3.1.1/modules/lib/zcbor)
#
CONFIG_ZEPHYR_ZCBOR_MODULE=y
# CONFIG_ZCBOR is not set
# end of zcbor (/opt/nordic/ncs/v3.1.1/modules/lib/zcbor)

#
# nrfxlib (/opt/nordic/ncs/v3.1.1/nrfxlib)
#

#
# Nordic nrfxlib
#

#
# nrf_modem (Modem library)
#
CONFIG_NRF_MODEM=y
CONFIG_NRF_MODEM_LINK_BINARY=y
CONFIG_NRF_MODEM_LINK_BINARY_CELLULAR=y
# CONFIG_NRF_MODEM_LINK_BINARY_DECT_PHY is not set
# CONFIG_NRF_MODEM_LOG is not set
CONFIG_NRF_MODEM_SHMEM_CTRL_SIZE=0x4e8
# end of nrf_modem (Modem library)

# CONFIG_NFC_T2T_NRFXLIB is not set
# CONFIG_NFC_T4T_NRFXLIB is not set

#
# Crypto libraries for nRF5x SOCs.
#
CONFIG_HAS_HW_NRF_CC3XX=y
# CONFIG_NRF_OBERON is not set
# CONFIG_NRF_CC310_BL is not set
# end of Crypto libraries for nRF5x SOCs.

# CONFIG_NRF_RPC is not set
CONFIG_NRF_802154_SOURCE_NRFXLIB=y
# CONFIG_NRF_DM is not set
# CONFIG_NRF_FUEL_GAUGE is not set
# end of Nordic nrfxlib

CONFIG_ZEPHYR_NRFXLIB_MODULE=y
# end of nrfxlib (/opt/nordic/ncs/v3.1.1/nrfxlib)

CONFIG_ZEPHYR_NRF_HW_MODELS_MODULE=y

#
# connectedhomeip (/opt/nordic/ncs/v3.1.1/modules/lib/matter)
#
# CONFIG_CHIP is not set
# CONFIG_CHIP_CUSTOM_BLE_ADV_DATA is not set
CONFIG_ZEPHYR_CONNECTEDHOMEIP_MODULE=y
# end of connectedhomeip (/opt/nordic/ncs/v3.1.1/modules/lib/matter)

# CONFIG_LIBMETAL is not set
# CONFIG_LVGL is not set
# CONFIG_HAS_MEC_HAL is not set
# CONFIG_HAS_MPFS_HAL is not set
# CONFIG_HAS_MEC5_HAL is not set
# CONFIG_OPENAMP is not set
# CONFIG_MIPI_SYST_LIB is not set
# CONFIG_HAS_TELINK_DRIVERS is not set
# CONFIG_MCUBOOT_BOOTUTIL_LIB is not set

#
# Unavailable modules, please install those via the project manifest.
#

#
# hal_bouffalolab module not available.
#

#
# hal_gigadevice module not available.
#

#
# hal_nxp module not available.
#

#
# libsbc module not available.
#

#
# Trusted-firmware-a module not available.
#

#
# LoRa Basics Modem module not available.
#

#
# THRIFT module not available.
#
# CONFIG_ACPI is not set
# end of Modules

CONFIG_BOARD="nrf9151dk"
CONFIG_BOARD_REVISION=""
CONFIG_BOARD_TARGET="nrf9151dk/nrf9151/ns"
# CONFIG_NET_DRIVERS is not set
CONFIG_BOARD_NRF9151DK_NRF9151_NS=y
CONFIG_BOARD_QUALIFIERS="nrf9151/ns"

#
# Board Options
#
# end of Board Options

#
# Hardware Configuration
#
CONFIG_SOC="nrf9151"
CONFIG_SOC_SERIES="nrf91"
CONFIG_SOC_FAMILY="nordic_nrf"
CONFIG_SOC_FAMILY_NORDIC_NRF=y
CONFIG_SOC_SERIES_NRF91X=y
CONFIG_SOC_NRF9120=y
CONFIG_SOC_NRF9151_LACA=y
# CONFIG_HWINFO is not set
# CONFIG_BUILD_OUTPUT_INFO_HEADER is not set
CONFIG_SOC_COMPATIBLE_NRF=y
CONFIG_SOC_NORDIC_BSP_NAME="stable"
CONFIG_HAS_HW_NRF_CC310=y
CONFIG_HAS_HW_NRF_CLOCK=y
CONFIG_HAS_HW_NRF_DPPIC=y
CONFIG_HAS_HW_NRF_EGU0=y
CONFIG_HAS_HW_NRF_EGU1=y
CONFIG_HAS_HW_NRF_EGU2=y
CONFIG_HAS_HW_NRF_EGU3=y
CONFIG_HAS_HW_NRF_EGU4=y
CONFIG_HAS_HW_NRF_EGU5=y
CONFIG_HAS_HW_NRF_GPIO0=y
CONFIG_HAS_HW_NRF_GPIOTE1=y
CONFIG_HAS_HW_NRF_KMU=y
CONFIG_HAS_HW_NRF_NVMC_PE=y
CONFIG_HAS_HW_NRF_POWER=y
CONFIG_HAS_HW_NRF_SAADC=y
CONFIG_HAS_HW_NRF_UARTE0=y
CONFIG_HAS_HW_NRF_UARTE1=y
CONFIG_HAS_HW_NRF_VMC=y
# CONFIG_NRF_SYS_EVENT is not set
# CONFIG_NRF_PERIPHCONF_SECTION is not set
# CONFIG_IS_IRONSIDE_SE_SECONDARY_IMAGE is not set
# CONFIG_IS_GEN_UICR_IMAGE is not set
CONFIG_NRF_ENABLE_ICACHE=y
CONFIG_NRF_TRUSTZONE_FLASH_REGION_SIZE=0x8000
CONFIG_NRF_SPU_RAM_REGION_SIZE=0x2000
CONFIG_NRF_TRUSTZONE_RAM_REGION_SIZE=0x2000
CONFIG_NRF_RTC_TIMER_USER_CHAN_COUNT=0
# CONFIG_SOC_NRF54H20_PM_S2RAM_OVERRIDE is not set
CONFIG_NRF_SOC_SECURE_SUPPORTED=y
CONFIG_TFM_NRF_NS_STORAGE=y
CONFIG_NRF_APPROTECT_USE_UICR=y
# CONFIG_NRF_APPROTECT_LOCK is not set
# CONFIG_NRF_APPROTECT_USER_HANDLING is not set
CONFIG_NRF_SECURE_APPROTECT_USE_UICR=y
# CONFIG_NRF_SECURE_APPROTECT_LOCK is not set
# CONFIG_NRF_SECURE_APPROTECT_USER_HANDLING is not set
# CONFIG_NRF_TRACE_PORT is not set
CONFIG_GPIO_INIT_PRIORITY=40
# CONFIG_SOC_LOG_LEVEL_OFF is not set
# CONFIG_SOC_LOG_LEVEL_ERR is not set
# CONFIG_SOC_LOG_LEVEL_WRN is not set
# CONFIG_SOC_LOG_LEVEL_INF is not set
# CONFIG_SOC_LOG_LEVEL_DBG is not set
CONFIG_SOC_LOG_LEVEL_DEFAULT=y
CONFIG_SOC_LOG_LEVEL=3
# end of Hardware Configuration

CONFIG_ARCH="arm"
# CONFIG_EXTRA_EXCEPTION_INFO is not set
CONFIG_ARCH_HAS_SINGLE_THREAD_SUPPORT=y
CONFIG_CPU_CORTEX=y
CONFIG_ARM_MPU_REGION_MIN_ALIGN_AND_SIZE=32
# CONFIG_MPU_ALLOW_FLASH_WRITE is not set

#
# ARM Options
#
CONFIG_CPU_CORTEX_M=y
# CONFIG_ARM_ZIMAGE_HEADER is not set
CONFIG_ISA_THUMB2=y
CONFIG_ASSEMBLER_ISA_THUMB2=y
CONFIG_COMPILER_ISA_THUMB2=y
CONFIG_STACK_ALIGN_DOUBLE_WORD=y
# CONFIG_RUNTIME_NMI is not set
# CONFIG_PLATFORM_SPECIFIC_INIT is not set
CONFIG_FAULT_DUMP=2
CONFIG_BUILTIN_STACK_GUARD=y
CONFIG_ARM_STACK_PROTECTION=y
CONFIG_ARM_NONSECURE_FIRMWARE=y
CONFIG_ARM_NONSECURE_PREEMPTIBLE_SECURE_CALLS=y
CONFIG_ARM_STORE_EXC_RETURN=y
CONFIG_FP16=y
CONFIG_FP16_IEEE=y
# CONFIG_FP16_ALT is not set
CONFIG_CPU_CORTEX_M33=y
CONFIG_CPU_CORTEX_M_HAS_SYSTICK=y
CONFIG_CPU_CORTEX_M_HAS_DWT=y
CONFIG_CPU_CORTEX_M_HAS_BASEPRI=y
CONFIG_CPU_CORTEX_M_HAS_VTOR=y
CONFIG_CPU_CORTEX_M_HAS_SPLIM=y
CONFIG_CPU_CORTEX_M_HAS_PROGRAMMABLE_FAULT_PRIOS=y
CONFIG_CPU_CORTEX_M_HAS_CMSE=y
CONFIG_ARMV7_M_ARMV8_M_MAINLINE=y
CONFIG_ARMV8_M_MAINLINE=y
CONFIG_ARMV8_M_SE=y
CONFIG_ARMV7_M_ARMV8_M_FP=y
CONFIG_ARMV8_M_DSP=y

#
# ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33/M55 options
#
# CONFIG_SW_VECTOR_RELAY is not set
# CONFIG_CORTEX_M_DWT is not set
# CONFIG_CORTEX_M_DEBUG_MONITOR_HOOK is not set
# CONFIG_TRAP_UNALIGNED_ACCESS is not set
# end of ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33/M55 options

CONFIG_NULL_POINTER_EXCEPTION_DETECTION_NONE=y
CONFIG_ARM_TRUSTZONE_M=y

#
# ARM TrustZone-M Options
#

#
# Non-secure firmware
#
# CONFIG_ARM_FIRMWARE_USES_SECURE_ENTRY_FUNCS is not set
# end of ARM TrustZone-M Options

# CONFIG_MPU_STACK_GUARD is not set
# CONFIG_MPU_DISABLE_BACKGROUND_MAP is not set
# CONFIG_CUSTOM_SECTION_ALIGN is not set
CONFIG_CUSTOM_SECTION_MIN_ALIGN_SIZE=32
CONFIG_CPU_HAS_NRF_IDAU=y
# end of ARM Options

CONFIG_ARM=y
CONFIG_ARCH_IS_SET=y

#
# General Architecture Options
#
# CONFIG_SEMIHOST is not set
CONFIG_ARCH_SUPPORTS_ROM_OFFSET=y
CONFIG_ARM_MPU=y
# CONFIG_ARCH_LOG_LEVEL_OFF is not set
# CONFIG_ARCH_LOG_LEVEL_ERR is not set
# CONFIG_ARCH_LOG_LEVEL_WRN is not set
# CONFIG_ARCH_LOG_LEVEL_INF is not set
# CONFIG_ARCH_LOG_LEVEL_DBG is not set
CONFIG_ARCH_LOG_LEVEL_DEFAULT=y
CONFIG_ARCH_LOG_LEVEL=3
CONFIG_LITTLE_ENDIAN=y
# CONFIG_TRUSTED_EXECUTION_SECURE is not set
CONFIG_TRUSTED_EXECUTION_NONSECURE=y
# CONFIG_USERSPACE is not set
# CONFIG_NOINIT_SNIPPET_FIRST is not set
CONFIG_GEN_PRIV_STACKS=y
# CONFIG_STACK_GROWS_UP is not set
# CONFIG_FRAME_POINTER is not set

#
# Interrupt Configuration
#
# CONFIG_ISR_TABLES_LOCAL_DECLARATION is not set
CONFIG_ARCH_DEVICE_STATE_ALIGN=4
CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_ADDRESS=y
# CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_CODE is not set
# CONFIG_SRAM_SW_ISR_TABLE is not set
CONFIG_EXCEPTION_DEBUG=y
# CONFIG_SIMPLIFIED_EXCEPTION_CODES is not set
# end of Interrupt Configuration
# end of General Architecture Options

CONFIG_ARCH_HAS_TIMING_FUNCTIONS=y
CONFIG_ARCH_HAS_TRUSTED_EXECUTION=y
CONFIG_ARCH_HAS_STACK_PROTECTION=y
CONFIG_ARCH_HAS_USERSPACE=y
CONFIG_ARCH_HAS_EXECUTABLE_PAGE_BIT=y
CONFIG_ARCH_HAS_RAMFUNC_SUPPORT=y
CONFIG_ARCH_HAS_VECTOR_TABLE_RELOCATION=y
CONFIG_ARCH_HAS_NESTED_EXCEPTION_DETECTION=y
CONFIG_ARCH_SUPPORTS_COREDUMP=y
CONFIG_ARCH_SUPPORTS_COREDUMP_THREADS=y
CONFIG_ARCH_SUPPORTS_COREDUMP_STACK_PTR=y
CONFIG_ARCH_SUPPORTS_ARCH_HW_INIT=y
CONFIG_ARCH_SUPPORTS_ROM_START=y
CONFIG_ARCH_HAS_EXTRA_EXCEPTION_INFO=y
CONFIG_ARCH_HAS_THREAD_LOCAL_STORAGE=y
CONFIG_ARCH_HAS_SUSPEND_TO_RAM=y
CONFIG_ARCH_HAS_THREAD_ABORT=y
CONFIG_ARCH_HAS_CODE_DATA_RELOCATION=y
CONFIG_CPU_HAS_TEE=y
CONFIG_CPU_HAS_FPU=y
CONFIG_CPU_HAS_MPU=y
CONFIG_MPU=y
# CONFIG_MPU_LOG_LEVEL_OFF is not set
# CONFIG_MPU_LOG_LEVEL_ERR is not set
# CONFIG_MPU_LOG_LEVEL_WRN is not set
# CONFIG_MPU_LOG_LEVEL_INF is not set
# CONFIG_MPU_LOG_LEVEL_DBG is not set
CONFIG_MPU_LOG_LEVEL_DEFAULT=y
CONFIG_MPU_LOG_LEVEL=3
CONFIG_MPU_REQUIRES_NON_OVERLAPPING_REGIONS=y
CONFIG_MPU_GAP_FILLING=y
CONFIG_SRAM_REGION_PERMISSIONS=y

#
# DSP Options
#
# end of DSP Options

#
# Floating Point Options
#
# end of Floating Point Options

#
# Cache Options
#
# end of Cache Options

CONFIG_TOOLCHAIN_HAS_BUILTIN_FFS=y
CONFIG_ARCH_HAS_CUSTOM_SWAP_TO_MAIN=y

#
# General Kernel Options
#
# CONFIG_KERNEL_LOG_LEVEL_OFF is not set
# CONFIG_KERNEL_LOG_LEVEL_ERR is not set
# CONFIG_KERNEL_LOG_LEVEL_WRN is not set
# CONFIG_KERNEL_LOG_LEVEL_INF is not set
# CONFIG_KERNEL_LOG_LEVEL_DBG is not set
CONFIG_KERNEL_LOG_LEVEL_DEFAULT=y
CONFIG_KERNEL_LOG_LEVEL=3
CONFIG_NUM_COOP_PRIORITIES=16
CONFIG_MAIN_THREAD_PRIORITY=0
CONFIG_COOP_ENABLED=y
CONFIG_PREEMPT_ENABLED=y
CONFIG_PRIORITY_CEILING=-127
# CONFIG_SCHED_DEADLINE is not set
CONFIG_THREAD_STACK_INFO=y
# CONFIG_THREAD_CUSTOM_DATA is not set
# CONFIG_DYNAMIC_THREAD is not set
# CONFIG_SCHED_DUMB is not set
CONFIG_SCHED_SIMPLE=y
# CONFIG_SCHED_SCALABLE is not set
# CONFIG_SCHED_MULTIQ is not set
# CONFIG_WAITQ_DUMB is not set
# CONFIG_WAITQ_SCALABLE is not set
CONFIG_WAITQ_SIMPLE=y

#
# Misc Kernel related options
#
CONFIG_LIBC_ERRNO=y
CONFIG_ERRNO=y
CONFIG_CURRENT_THREAD_USE_TLS=y
# end of Misc Kernel related options

#
# Kernel Debugging and Metrics
#
CONFIG_BOOT_DELAY=0
# CONFIG_BOOT_CLEAR_SCREEN is not set
CONFIG_THREAD_MONITOR=y
CONFIG_THREAD_NAME=y
CONFIG_THREAD_MAX_NAME_LEN=32
# CONFIG_THREAD_RUNTIME_STATS is not set
# end of Kernel Debugging and Metrics

# CONFIG_OBJ_CORE is not set
# CONFIG_WORKQUEUE_WORK_TIMEOUT is not set

#
# System Work Queue Options
#
# CONFIG_SYSTEM_WORKQUEUE_NO_YIELD is not set
CONFIG_SYSTEM_WORKQUEUE_WORK_TIMEOUT_MS=0
# end of System Work Queue Options

#
# Barrier Operations
#
CONFIG_BARRIER_OPERATIONS_ARCH=y
# end of Barrier Operations

#
# Atomic Operations
#
CONFIG_ATOMIC_OPERATIONS_BUILTIN=y
# end of Atomic Operations

#
# Timer API Options
#
CONFIG_TIMESLICING=y
CONFIG_TIMESLICE_PRIORITY=0
# CONFIG_TIMESLICE_PER_THREAD is not set
# end of Timer API Options

#
# Other Kernel Object Options
#
CONFIG_POLL=y
# CONFIG_MEM_SLAB_POINTER_VALIDATE is not set
# CONFIG_MEM_SLAB_TRACE_MAX_UTILIZATION is not set
CONFIG_NUM_MBOX_ASYNC_MSGS=10
# CONFIG_EVENTS is not set
# CONFIG_HEAP_MEM_POOL_IGNORE_MIN is not set
# end of Other Kernel Object Options

CONFIG_SWAP_NONATOMIC=y
CONFIG_TIMEOUT_64BIT=y
CONFIG_SYS_CLOCK_MAX_TIMEOUT_DAYS=365

#
# Security Options
#
CONFIG_STACK_POINTER_RANDOM=0
# end of Security Options

#
# Memory Domains
#
CONFIG_ARCH_MEM_DOMAIN_SUPPORTS_ISOLATED_STACKS=y
CONFIG_MEM_DOMAIN_ISOLATED_STACKS=y
# end of Memory Domains

#
# SMP Options
#
# CONFIG_TICKET_SPINLOCKS is not set
# end of SMP Options

CONFIG_TOOLCHAIN_SUPPORTS_THREAD_LOCAL_STORAGE=y
CONFIG_THREAD_LOCAL_STORAGE=y
CONFIG_TOOLCHAIN_SUPPORTS_STATIC_INIT_GNU=y
# CONFIG_STATIC_INIT_GNU is not set
# CONFIG_BOOTARGS is not set
# end of General Kernel Options

#
# Device Options
#
# CONFIG_DEVICE_MUTABLE is not set
# CONFIG_DEVICE_DT_METADATA is not set
CONFIG_DEVICE_DEINIT_SUPPORT=y
# end of Device Options

#
# Initialization Priorities
#
CONFIG_KERNEL_INIT_PRIORITY_OBJECTS=30
CONFIG_KERNEL_INIT_PRIORITY_LIBC=35
CONFIG_KERNEL_INIT_PRIORITY_DEFAULT=40
CONFIG_KERNEL_INIT_PRIORITY_DEVICE=50
CONFIG_APPLICATION_INIT_PRIORITY=90
# end of Initialization Priorities

#
# Virtual Memory Support
#

#
# MMU Features
#
# end of MMU Features
# end of Virtual Memory Support

#
# SoC and Board Hooks
#
# CONFIG_SOC_EARLY_RESET_HOOK is not set
# CONFIG_SOC_PREP_HOOK is not set
# CONFIG_SOC_EARLY_INIT_HOOK is not set
# CONFIG_SOC_LATE_INIT_HOOK is not set
# CONFIG_SOC_PER_CORE_INIT_HOOK is not set
# CONFIG_BOARD_EARLY_INIT_HOOK is not set
# CONFIG_BOARD_LATE_INIT_HOOK is not set
# end of SoC and Board Hooks

#
# Device Drivers
#
# CONFIG_ADC is not set
# CONFIG_AUDIO is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_BBRAM is not set
CONFIG_BT_DRIVERS=y

#
# Bluetooth HCI Driver Options
#
CONFIG_BT_UART=y
CONFIG_BT_H4=y
CONFIG_BT_HCI_INIT_PRIORITY=50
# CONFIG_HCI_NXP_SET_CAL_DATA_ANNEX100 is not set
CONFIG_BT_DRV_TX_STACK_SIZE=256
CONFIG_BT_DRV_RX_STACK_SIZE=1200
# CONFIG_CAN is not set
# CONFIG_CHARGER is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_OFF is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_ERR is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_WRN is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_INF is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_DBG is not set
CONFIG_CLOCK_CONTROL_LOG_LEVEL_DEFAULT=y
CONFIG_CLOCK_CONTROL_LOG_LEVEL=3
CONFIG_CLOCK_CONTROL_NRF=y
CONFIG_CLOCK_CONTROL_NRF_K32SRC_FREQUENCY=32768
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_500PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_250PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_150PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_100PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_75PPM is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_50PPM=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_30PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_20PPM is not set
CONFIG_CLOCK_CONTROL_NRF_ACCURACY=50
# CONFIG_CLOCK_CONTROL_FIXED_RATE_CLOCK is not set
# CONFIG_COMPARATOR is not set
CONFIG_CONSOLE_INPUT_MAX_LINE_LEN=128
CONFIG_CONSOLE_HAS_DRIVER=y
# CONFIG_CONSOLE_HANDLER is not set
CONFIG_CONSOLE_INIT_PRIORITY=60
CONFIG_UART_CONSOLE=y
# CONFIG_UART_CONSOLE_DEBUG_SERVER_HOOKS is not set
# CONFIG_UART_CONSOLE_MCUMGR is not set
# CONFIG_RAM_CONSOLE is not set
# CONFIG_IPM_CONSOLE_SENDER is not set
# CONFIG_IPM_CONSOLE_RECEIVER is not set
# CONFIG_UART_MCUMGR is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_OFF is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_ERR is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_WRN is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_INF is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_DBG is not set
CONFIG_UART_CONSOLE_LOG_LEVEL_DEFAULT=y
CONFIG_UART_CONSOLE_LOG_LEVEL=3
# CONFIG_EFI_CONSOLE is not set
# CONFIG_COREDUMP_DEVICE is not set
# CONFIG_CRC_DRIVER is not set
# CONFIG_CRYPTO is not set
# CONFIG_DAC is not set
# CONFIG_DAI is not set
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DISK_DRIVERS is not set
# CONFIG_DISPLAY is not set
# CONFIG_DMA is not set
# CONFIG_DP_DRIVER is not set
# CONFIG_EDAC is not set
# CONFIG_EEPROM is not set
CONFIG_ENTROPY_GENERATOR=y
# CONFIG_ENTROPY_LOG_LEVEL_OFF is not set
# CONFIG_ENTROPY_LOG_LEVEL_ERR is not set
# CONFIG_ENTROPY_LOG_LEVEL_WRN is not set
# CONFIG_ENTROPY_LOG_LEVEL_INF is not set
# CONFIG_ENTROPY_LOG_LEVEL_DBG is not set
CONFIG_ENTROPY_LOG_LEVEL_DEFAULT=y
CONFIG_ENTROPY_LOG_LEVEL=3
CONFIG_ENTROPY_INIT_PRIORITY=50
# CONFIG_FAKE_ENTROPY_NATIVE_POSIX is not set
CONFIG_ENTROPY_PSA_CRYPTO_RNG=y
CONFIG_ENTROPY_HAS_DRIVER=y
# CONFIG_ESPI is not set

#
# Firmware drivers
#
# CONFIG_ARM_SCMI is not set
# end of Firmware drivers

# CONFIG_FPGA is not set
# CONFIG_FUEL_GAUGE is not set
# CONFIG_GNSS is not set
# CONFIG_GPIO_LOG_LEVEL_OFF is not set
# CONFIG_GPIO_LOG_LEVEL_ERR is not set
# CONFIG_GPIO_LOG_LEVEL_WRN is not set
# CONFIG_GPIO_LOG_LEVEL_INF is not set
# CONFIG_GPIO_LOG_LEVEL_DBG is not set
CONFIG_GPIO_LOG_LEVEL_DEFAULT=y
CONFIG_GPIO_LOG_LEVEL=3
# CONFIG_GPIO_GET_DIRECTION is not set
# CONFIG_GPIO_GET_CONFIG is not set
# CONFIG_GPIO_HOGS is not set
# CONFIG_GPIO_ENABLE_DISABLE_INTERRUPT is not set
CONFIG_GPIO_NRFX=y
CONFIG_GPIO_NRFX_INTERRUPT=y
# CONFIG_HAPTICS is not set
# CONFIG_HWSPINLOCK is not set
# CONFIG_I2S is not set
# CONFIG_I3C is not set

#
# Interrupt controller drivers
#
CONFIG_INTC_INIT_PRIORITY=40
# CONFIG_INTC_LOG_LEVEL_OFF is not set
# CONFIG_INTC_LOG_LEVEL_ERR is not set
# CONFIG_INTC_LOG_LEVEL_WRN is not set
# CONFIG_INTC_LOG_LEVEL_INF is not set
# CONFIG_INTC_LOG_LEVEL_DBG is not set
CONFIG_INTC_LOG_LEVEL_DEFAULT=y
CONFIG_INTC_LOG_LEVEL=3
# end of Interrupt controller drivers

# CONFIG_IPM is not set
# CONFIG_LED is not set
# CONFIG_LED_STRIP is not set
# CONFIG_LORA is not set
# CONFIG_MBOX is not set
# CONFIG_MDIO is not set
# CONFIG_MIPI_DBI is not set

#
# Miscellaneous Drivers
#
# CONFIG_TIMEAWARE_GPIO is not set

#
# Interconn Drivers
#
# end of Interconn Drivers
# end of Miscellaneous Drivers

# CONFIG_MM_DRV is not set
# CONFIG_MSPI is not set
# CONFIG_PCIE is not set
# CONFIG_PCIE_ENDPOINT is not set
# CONFIG_PECI is not set
CONFIG_PINCTRL=y
# CONFIG_PINCTRL_LOG_LEVEL_OFF is not set
# CONFIG_PINCTRL_LOG_LEVEL_ERR is not set
# CONFIG_PINCTRL_LOG_LEVEL_WRN is not set
# CONFIG_PINCTRL_LOG_LEVEL_INF is not set
# CONFIG_PINCTRL_LOG_LEVEL_DBG is not set
CONFIG_PINCTRL_LOG_LEVEL_DEFAULT=y
CONFIG_PINCTRL_LOG_LEVEL=3
CONFIG_PINCTRL_STORE_REG=y
# CONFIG_PINCTRL_DYNAMIC is not set
CONFIG_PINCTRL_KEEP_SLEEP_STATE=y
# CONFIG_PINCTRL_NPCX_EX is not set
CONFIG_PINCTRL_NRF=y
# CONFIG_PM_CPU_OPS is not set
# CONFIG_PS2 is not set
# CONFIG_PSI5 is not set
# CONFIG_PTP_CLOCK is not set
# CONFIG_PWM is not set
# CONFIG_RETAINED_MEM is not set
# CONFIG_RTC is not set
# CONFIG_SDHC is not set
# CONFIG_SENT is not set

#
# Capabilities
#
CONFIG_SERIAL_HAS_DRIVER=y
CONFIG_SERIAL_SUPPORT_ASYNC=y
CONFIG_SERIAL_SUPPORT_INTERRUPT=y
CONFIG_SERIAL_INIT_PRIORITY=50
# CONFIG_UART_LOG_LEVEL_OFF is not set
# CONFIG_UART_LOG_LEVEL_ERR is not set
# CONFIG_UART_LOG_LEVEL_WRN is not set
# CONFIG_UART_LOG_LEVEL_INF is not set
# CONFIG_UART_LOG_LEVEL_DBG is not set
CONFIG_UART_LOG_LEVEL_DEFAULT=y
CONFIG_UART_LOG_LEVEL=3
CONFIG_UART_ASYNC_API=y
CONFIG_UART_EXCLUSIVE_API_CALLBACKS=y
# CONFIG_UART_LINE_CTRL is not set
# CONFIG_UART_DRV_CMD is not set
# CONFIG_UART_WIDE_DATA is not set
# CONFIG_UART_PIPE is not set
# CONFIG_UART_ASYNC_RX_HELPER is not set

#
# Serial Drivers
#
# CONFIG_UART_NATIVE_POSIX is not set
# CONFIG_UART_NPCX_FIFO_EX is not set
CONFIG_UART_NRFX=y
CONFIG_UART_NRFX_UARTE=y
CONFIG_UART_NRFX_UARTE_LEGACY_SHIM=y
CONFIG_UART_ASYNC_TX_CACHE_SIZE=8
# CONFIG_UARTE_NRFX_UARTE_COUNT_BYTES_WITH_TIMER is not set
# CONFIG_UART_NRFX_UARTE_DIRECT_ISR is not set
CONFIG_UART_0_INTERRUPT_DRIVEN=y
CONFIG_UART_0_ENHANCED_POLL_OUT=y
# CONFIG_UART_0_NRF_PARITY_BIT is not set
CONFIG_UART_0_NRF_TX_BUFFER_SIZE=32
# CONFIG_UART_0_NRF_HW_ASYNC is not set
CONFIG_UART_0_NRF_ASYNC_LOW_POWER=y
# CONFIG_UART_1_INTERRUPT_DRIVEN is not set
CONFIG_UART_1_ASYNC=y
CONFIG_UART_1_ENHANCED_POLL_OUT=y
# CONFIG_UART_1_NRF_PARITY_BIT is not set
CONFIG_UART_1_NRF_TX_BUFFER_SIZE=32
CONFIG_UART_1_NRF_HW_ASYNC=y
CONFIG_UART_1_NRF_ASYNC_LOW_POWER=y
CONFIG_UART_1_NRF_HW_ASYNC_TIMER=2
# CONFIG_SMBUS is not set
# CONFIG_STEPPER is not set

#
# Timer drivers
#
# CONFIG_TIMER_READS_ITS_FREQUENCY_AT_RUNTIME is not set
# CONFIG_SYSTEM_CLOCK_SLOPPY_IDLE is not set
CONFIG_SYSTEM_CLOCK_INIT_PRIORITY=0
CONFIG_TICKLESS_CAPABLE=y
CONFIG_SYSTEM_TIMER_HAS_DISABLE_SUPPORT=y
CONFIG_NRF_RTC_TIMER=y
# CONFIG_NRF_RTC_TIMER_TRIGGER_OVERFLOW is not set
CONFIG_NRF_RTC_COUNTER_BIT_WIDTH=24
# CONFIG_SYSTEM_CLOCK_NO_WAIT is not set
# CONFIG_SYSTEM_CLOCK_WAIT_FOR_AVAILABILITY is not set
CONFIG_SYSTEM_CLOCK_WAIT_FOR_STABILITY=y
# end of Timer drivers

# CONFIG_USB_BC12 is not set
# CONFIG_UDC_DRIVER is not set
# CONFIG_UHC_DRIVER is not set
# CONFIG_UVB is not set
# CONFIG_USB_DEVICE_DRIVER is not set

#
# USB common
#
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_OFF is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_ERR is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_WRN is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_INF is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_DBG is not set
CONFIG_NRF_USBD_COMMON_LOG_LEVEL_DEFAULT=y
CONFIG_NRF_USBD_COMMON_LOG_LEVEL=3
# end of USB common

# CONFIG_USBC_TCPC_DRIVER is not set
# CONFIG_USBC_LOG_LEVEL_OFF is not set
# CONFIG_USBC_LOG_LEVEL_ERR is not set
# CONFIG_USBC_LOG_LEVEL_WRN is not set
# CONFIG_USBC_LOG_LEVEL_INF is not set
# CONFIG_USBC_LOG_LEVEL_DBG is not set
CONFIG_USBC_LOG_LEVEL_DEFAULT=y
CONFIG_USBC_LOG_LEVEL=3
# CONFIG_USBC_VBUS_DRIVER is not set
# CONFIG_USBC_PPC_DRIVER is not set
# CONFIG_VIDEO is not set
# CONFIG_VIRTIO is not set
# CONFIG_VIRTIO_LOG_LEVEL_OFF is not set
# CONFIG_VIRTIO_LOG_LEVEL_ERR is not set
# CONFIG_VIRTIO_LOG_LEVEL_WRN is not set
# CONFIG_VIRTIO_LOG_LEVEL_INF is not set
# CONFIG_VIRTIO_LOG_LEVEL_DBG is not set
CONFIG_VIRTIO_LOG_LEVEL_DEFAULT=y
CONFIG_VIRTIO_LOG_LEVEL=3
# CONFIG_VIRTUALIZATION is not set
# CONFIG_W1 is not set
# CONFIG_TEE is not set
# end of Device Drivers

CONFIG_REQUIRES_FULL_LIBC=y
# CONFIG_REQUIRES_FLOAT_PRINTF is not set
# CONFIG_LIBC_ALLOW_LESS_THAN_64BIT_TIME is not set
CONFIG_FULL_LIBC_SUPPORTED=y
CONFIG_MINIMAL_LIBC_SUPPORTED=y
CONFIG_NEWLIB_LIBC_SUPPORTED=y
CONFIG_PICOLIBC_SUPPORTED=y

#
# C Library
#
CONFIG_PICOLIBC=y
# CONFIG_NEWLIB_LIBC is not set
# CONFIG_EXTERNAL_LIBC is not set
CONFIG_HAS_NEWLIB_LIBC_NANO=y
CONFIG_COMMON_LIBC_ABORT=y
# CONFIG_COMMON_LIBC_ASCTIME_R is not set
# CONFIG_COMMON_LIBC_CTIME_R is not set
CONFIG_COMMON_LIBC_TIME=y
CONFIG_COMMON_LIBC_MALLOC=y
CONFIG_COMMON_LIBC_CALLOC=y
CONFIG_COMMON_LIBC_REALLOCARRAY=y
# CONFIG_COMMON_LIBC_REMOVE is not set
# CONFIG_PICOLIBC_USE_MODULE is not set
CONFIG_PICOLIBC_USE_TOOLCHAIN=y
# CONFIG_PICOLIBC_IO_FLOAT is not set
CONFIG_PICOLIBC_IO_LONG_LONG=y
CONFIG_STDOUT_CONSOLE=y
CONFIG_NEED_LIBC_MEM_PARTITION=y
# end of C Library

#
# C++ Language Support
#
# CONFIG_CPP is not set
# end of C++ Language Support

#
# Additional libraries
#

#
# Hash Function Support
#
# CONFIG_SYS_HASH_FUNC32 is not set
# end of Hash Function Support

#
# Hashmap (Hash Table) Support
#
# CONFIG_SYS_HASH_MAP is not set
# end of Hashmap (Hash Table) Support

#
# Heap and Memory Allocation
#
# CONFIG_SYS_HEAP_STRESS is not set
# CONFIG_SYS_HEAP_INFO is not set
CONFIG_SYS_HEAP_ALLOC_LOOPS=3
# CONFIG_SYS_HEAP_RUNTIME_STATS is not set
CONFIG_SYS_HEAP_ARRAY_SIZE=0
# CONFIG_SYS_HEAP_LISTENER is not set
# CONFIG_SYS_HEAP_SMALL_ONLY is not set
# CONFIG_SYS_HEAP_BIG_ONLY is not set
CONFIG_SYS_HEAP_AUTO=y
# CONFIG_MULTI_HEAP is not set
# CONFIG_SHARED_MULTI_HEAP is not set
# end of Heap and Memory Allocation

#
# Memory Blocks
#
# CONFIG_SYS_MEM_BLOCKS is not set
# end of Memory Blocks

CONFIG_NET_BUF=y
# CONFIG_NET_BUF_LOG is not set
# CONFIG_NET_BUF_LOG_LEVEL_OFF is not set
# CONFIG_NET_BUF_LOG_LEVEL_ERR is not set
# CONFIG_NET_BUF_LOG_LEVEL_WRN is not set
# CONFIG_NET_BUF_LOG_LEVEL_INF is not set
# CONFIG_NET_BUF_LOG_LEVEL_DBG is not set
CONFIG_NET_BUF_LOG_LEVEL_DEFAULT=y
CONFIG_NET_BUF_LOG_LEVEL=3
# CONFIG_NET_BUF_POOL_USAGE is not set
CONFIG_NET_BUF_ALIGNMENT=0

#
# OS Support Library
#
# CONFIG_FDTABLE is not set
CONFIG_ZVFS_OPEN_MAX=4
# CONFIG_PRINTK_SYNC is not set
CONFIG_MPSC_PBUF=y
# CONFIG_SPSC_PBUF is not set
# CONFIG_MPSC_CLEAR_ALLOCATED is not set
CONFIG_HAS_POWEROFF=y
# CONFIG_POWEROFF is not set
CONFIG_CBPRINTF_COMPLETE=y
# CONFIG_CBPRINTF_NANO is not set
CONFIG_CBPRINTF_FULL_INTEGRAL=y
# CONFIG_CBPRINTF_REDUCED_INTEGRAL is not set
# CONFIG_CBPRINTF_FP_SUPPORT is not set
# CONFIG_CBPRINTF_FP_A_SUPPORT is not set
# CONFIG_CBPRINTF_LIBC_SUBSTS is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_OFF is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_ERR is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_WRN is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_INF is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_DBG is not set
CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_DEFAULT=y
CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL=3
# CONFIG_CBPRINTF_PACKAGE_LONGDOUBLE is not set
CONFIG_CBPRINTF_CONVERT_CHECK_PTR=y
# CONFIG_ZVFS is not set
# end of OS Support Library

#
# POSIX API Support
#

#
# POSIX Options
#
# CONFIG_POSIX_API is not set
CONFIG_POSIX_AEP_CHOICE_NONE=y
# CONFIG_POSIX_AEP_CHOICE_BASE is not set
# CONFIG_POSIX_AEP_CHOICE_PSE51 is not set
# CONFIG_POSIX_AEP_CHOICE_PSE52 is not set
# CONFIG_POSIX_AEP_CHOICE_PSE53 is not set
# CONFIG_POSIX_ASYNCHRONOUS_IO is not set
# CONFIG_POSIX_BARRIERS is not set
# CONFIG_POSIX_C_LANG_SUPPORT_R is not set
# CONFIG_POSIX_C_LIB_EXT is not set

#
# POSIX device I/O
#
# CONFIG_POSIX_DEVICE_IO is not set
CONFIG_POSIX_OPEN_MAX=4
# end of POSIX device I/O

# CONFIG_POSIX_FD_MGMT is not set
# CONFIG_POSIX_FILE_SYSTEM_R is not set
# CONFIG_POSIX_FILE_SYSTEM is not set

#
# POSIX memory
#
CONFIG_POSIX_PAGE_SIZE=0x40
# CONFIG_POSIX_SHARED_MEMORY_OBJECTS is not set
# CONFIG_POSIX_MAPPED_FILES is not set
# CONFIG_POSIX_MEMORY_PROTECTION is not set
# end of POSIX memory

# CONFIG_POSIX_MESSAGE_PASSING is not set
# CONFIG_POSIX_SINGLE_PROCESS is not set
# CONFIG_POSIX_MULTI_PROCESS is not set
# CONFIG_POSIX_THREADS is not set
# CONFIG_POSIX_READER_WRITER_LOCKS is not set

#
# POSIX scheduler options
#
# CONFIG_POSIX_PRIORITY_SCHEDULING is not set
# end of POSIX scheduler options

# CONFIG_POSIX_SEMAPHORES is not set

#
# POSIX signals
#
# CONFIG_POSIX_REALTIME_SIGNALS is not set
# CONFIG_POSIX_SIGNALS is not set
# end of POSIX signals

# CONFIG_POSIX_SPIN_LOCKS is not set

#
# POSIX synchronized I/O
#
# CONFIG_POSIX_FSYNC is not set
# CONFIG_POSIX_SYNCHRONIZED_IO is not set
# end of POSIX synchronized I/O

# CONFIG_POSIX_TIMERS is not set

#
# X/Open system interfaces
#
# CONFIG_XSI_REALTIME is not set
# CONFIG_XSI_SINGLE_PROCESS is not set
# CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_OFF is not set
# CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_ERR is not set
# CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_WRN is not set
# CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_INF is not set
# CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_DBG is not set
CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_DEFAULT=y
CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL=3
# CONFIG_XOPEN_STREAMS is not set
# CONFIG_XSI_SYSTEM_LOGGING is not set
# CONFIG_XSI_THREADS_EXT is not set
# end of X/Open system interfaces

#
# Miscellaneous POSIX-related options
#
# CONFIG_EVENTFD is not set
# end of Miscellaneous POSIX-related options

CONFIG_TC_PROVIDES_POSIX_C_LANG_SUPPORT_R=y
# end of POSIX Options

#
# POSIX Shell Utilities
#
# end of POSIX Shell Utilities
# end of POSIX API Support

# CONFIG_OPENAMP_RSC_TABLE is not set
# CONFIG_SMF is not set
CONFIG_LIBGCC_RTLIB=y

#
# Utility Library
#
# CONFIG_JSON_LIBRARY is not set
CONFIG_RING_BUFFER=y
# CONFIG_RING_BUFFER_LARGE is not set
CONFIG_NOTIFY=y
# CONFIG_BASE64 is not set
CONFIG_ONOFF=y
# CONFIG_UTF8 is not set
# CONFIG_COBS is not set
# end of Utility Library

#
# Universally Unique Identifier (UUID)
#
# CONFIG_UUID is not set
# end of Universally Unique Identifier (UUID)

# CONFIG_MIN_HEAP is not set
# end of Additional libraries

#
# Subsystems and OS Services
#
# CONFIG_BINDESC is not set
CONFIG_BT=y
CONFIG_BT_HCI=y
# CONFIG_BT_CUSTOM is not set
# CONFIG_BT_HCI_RAW is not set
# CONFIG_BT_HCI_RAW_H4 is not set
# CONFIG_BT_HCI_RAW_CMD_EXT is not set
CONFIG_BT_CONN_TX=y
# CONFIG_BT_LE_EXTENDED_FEAT_SET is not set
# CONFIG_BT_SCA_UPDATE is not set
# CONFIG_BT_TRANSMIT_POWER_CONTROL is not set
# CONFIG_BT_PATH_LOSS_MONITORING is not set
# CONFIG_BT_SUBRATING is not set
# CONFIG_BT_CHANNEL_SOUNDING is not set
# CONFIG_BT_ISO_PERIPHERAL is not set
# CONFIG_BT_ISO_BROADCASTER is not set

#
# Bluetooth buffer configuration
#
# end of Bluetooth buffer configuration

#
# Bluetooth Host
#

#
# L2CAP Options
#
# end of L2CAP Options

#
# ATT and GATT Options
#
# end of ATT and GATT Options

#
# GATT Services
#
# end of GATT Services

#
# Bluetooth Classic Options
#
# end of Bluetooth Classic Options
# end of Bluetooth Host

# CONFIG_BT_EAD is not set

#
# Bluetooth logging
#

#
# Common
#
# end of Common

#
# Libraries
#
# end of Libraries

#
# Host
#
# end of Host

#
# Services
#
# end of Services
# end of Bluetooth logging

#
# Controller Area Network (CAN) bus subsystem
#
# end of Controller Area Network (CAN) bus subsystem

# CONFIG_CONSOLE_SUBSYS is not set
# CONFIG_CPU_LOAD_METRIC is not set
# CONFIG_CPU_LOAD_LOG_LEVEL_OFF is not set
# CONFIG_CPU_LOAD_LOG_LEVEL_ERR is not set
# CONFIG_CPU_LOAD_LOG_LEVEL_WRN is not set
# CONFIG_CPU_LOAD_LOG_LEVEL_INF is not set
# CONFIG_CPU_LOAD_LOG_LEVEL_DBG is not set
CONFIG_CPU_LOAD_LOG_LEVEL_DEFAULT=y
CONFIG_CPU_LOAD_LOG_LEVEL=3
# CONFIG_CRC is not set
# CONFIG_DAP is not set

#
# System Monitoring Options
#
# CONFIG_THREAD_ANALYZER is not set
# end of System Monitoring Options

#
# Debugging Options
#
# CONFIG_DEBUG is not set
# CONFIG_UBSAN is not set
# CONFIG_STACK_USAGE is not set
# CONFIG_STACK_SENTINEL is not set
CONFIG_PRINTK=y
CONFIG_EARLY_CONSOLE=y
# CONFIG_FORCE_NO_ASSERT is not set
CONFIG_ASSERT_VERBOSE=y
# CONFIG_ASSERT_NO_FILE_INFO is not set
# CONFIG_ASSERT_NO_COND_INFO is not set
# CONFIG_ASSERT_NO_MSG_INFO is not set
# CONFIG_ASSERT_TEST is not set
# CONFIG_OVERRIDE_FRAME_POINTER_DEFAULT is not set
CONFIG_DEBUG_THREAD_INFO=y
# CONFIG_DEBUG_COREDUMP is not set
# CONFIG_SYMTAB is not set
# end of Debugging Options

# CONFIG_MIPI_STP_DECODER is not set
# CONFIG_CS_TRACE_DEFMT is not set
# CONFIG_CPU_LOAD is not set
CONFIG_CPU_LOAD_LOG_PERIODICALLY=0
# CONFIG_DISK_ACCESS is not set
# CONFIG_DSP is not set
# CONFIG_EMUL is not set
# CONFIG_CHARACTER_FRAMEBUFFER is not set

#
# File Systems
#
# CONFIG_FILE_SYSTEM_LIB_LINK is not set
# CONFIG_FILE_SYSTEM is not set
# end of File Systems

# CONFIG_GNSS_RTK is not set

#
# Inter Processor Communication
#
# CONFIG_RPMSG_SERVICE is not set
# CONFIG_IPC_SERVICE is not set
# end of Inter Processor Communication

# CONFIG_JWT is not set
# CONFIG_LLEXT is not set
# CONFIG_LLEXT_EDK is not set

#
# Logging
#
CONFIG_LOG_CORE_INIT_PRIORITY=0
CONFIG_LOG_MODE_DEFERRED=y
# CONFIG_LOG_MODE_IMMEDIATE is not set
# CONFIG_LOG_MODE_MINIMAL is not set
# CONFIG_LOG_FRONTEND is not set
# CONFIG_LOG_FRONTEND_OPT_API is not set
# CONFIG_LOG_CUSTOM_HEADER is not set
# CONFIG_LOG_MULTIDOMAIN is not set
CONFIG_LOG_FLUSH_SLEEP_US=10000

#
# Logging levels filtering
#
# CONFIG_LOG_RUNTIME_FILTERING is not set
CONFIG_LOG_DEFAULT_LEVEL=3
CONFIG_LOG_OVERRIDE_LEVEL=0
CONFIG_LOG_MAX_LEVEL=4
# end of Logging levels filtering

#
# Processing
#
CONFIG_LOG_PRINTK=y
CONFIG_LOG_MODE_OVERFLOW=y
# CONFIG_LOG_BLOCK_IN_THREAD is not set
CONFIG_LOG_PROCESS_TRIGGER_THRESHOLD=10
CONFIG_LOG_PROCESS_THREAD=y
CONFIG_LOG_PROCESS_THREAD_STARTUP_DELAY_MS=0
CONFIG_LOG_PROCESS_THREAD_SLEEP_MS=1000
# CONFIG_LOG_PROCESS_THREAD_CUSTOM_PRIORITY is not set
CONFIG_LOG_TRACE_SHORT_TIMESTAMP=y
# CONFIG_LOG_TIMESTAMP_64BIT is not set
# CONFIG_LOG_TIMESTAMP_USE_REALTIME is not set
# CONFIG_LOG_SPEED is not set
# end of Processing

#
# Output Formatting
#

#
# Prepend non-hexdump log message with function name
#
# CONFIG_LOG_FUNC_NAME_PREFIX_ERR is not set
# CONFIG_LOG_FUNC_NAME_PREFIX_WRN is not set
# CONFIG_LOG_FUNC_NAME_PREFIX_INF is not set
CONFIG_LOG_FUNC_NAME_PREFIX_DBG=y
# end of Prepend non-hexdump log message with function name

# CONFIG_LOG_MIPI_SYST_ENABLE is not set
# CONFIG_LOG_THREAD_ID_PREFIX is not set
# CONFIG_LOG_CUSTOM_FORMAT_SUPPORT is not set
CONFIG_LOG_BACKEND_SHOW_COLOR=y
# CONFIG_LOG_INFO_COLOR_GREEN is not set
# CONFIG_LOG_DBG_COLOR_BLUE is not set
CONFIG_LOG_TAG_MAX_LEN=0
CONFIG_LOG_BACKEND_SUPPORTS_FORMAT_TIMESTAMP=y
CONFIG_LOG_BACKEND_FORMAT_TIMESTAMP=y
CONFIG_LOG_OUTPUT_FORMAT_TIME_TIMESTAMP=y
# CONFIG_LOG_OUTPUT_FORMAT_LINUX_TIMESTAMP is not set
# CONFIG_LOG_OUTPUT_FORMAT_CUSTOM_TIMESTAMP is not set
# end of Output Formatting

#
# Backends
#
CONFIG_LOG_BACKEND_UART=y
# CONFIG_LOG_BACKEND_UART_ASYNC is not set
CONFIG_LOG_BACKEND_UART_BUFFER_SIZE=1
CONFIG_LOG_BACKEND_UART_AUTOSTART=y
CONFIG_LOG_BACKEND_UART_OUTPUT_TEXT=y
# CONFIG_LOG_BACKEND_UART_OUTPUT_DICTIONARY is not set
# CONFIG_LOG_BACKEND_UART_OUTPUT_CUSTOM is not set
CONFIG_LOG_BACKEND_UART_OUTPUT_DEFAULT=0
# CONFIG_LOG_BACKEND_IPC_SERVICE is not set
# end of Backends

#
# Misc
#
CONFIG_LOG_USE_VLA=y
CONFIG_LOG_SIMPLE_MSG_OPTIMIZE=y
# CONFIG_LOG_ALWAYS_RUNTIME is not set
# CONFIG_LOG_FMT_SECTION is not set
# CONFIG_LOG_FMT_STRING_VALIDATE is not set
# CONFIG_LOG_MEM_UTILIZATION is not set
CONFIG_LOG_FAILURE_REPORT_PERIOD=1000
# end of Misc

CONFIG_LOG_RATELIMIT=y
CONFIG_LOG_RATELIMIT_INTERVAL_MS=5000
CONFIG_LOG_OUTPUT=y
# end of Logging

CONFIG_MEM_ATTR=y
# CONFIG_MEM_ATTR_HEAP is not set

#
# Device Management
#

#
# Host command handler subsystem
#
# CONFIG_EC_HOST_CMD is not set
# end of Host command handler subsystem

# CONFIG_OSDP is not set
# end of Device Management

# CONFIG_MODBUS is not set
# CONFIG_MODEM_MODULES is not set

#
# Networking
#
# CONFIG_NETWORKING is not set
# end of Networking

#
# Power Management
#
# CONFIG_PM_POLICY_LATENCY_STANDALONE is not set
# end of Power Management

#
# Platform Management Communications Infrastructure (PMCI)
#
# CONFIG_MCTP is not set
# end of Platform Management Communications Infrastructure (PMCI)

#
# Portability
#
# end of Portability

# CONFIG_PROFILING is not set

#
# Random Number Generators
#
# CONFIG_TEST_RANDOM_GENERATOR is not set
CONFIG_TIMER_RANDOM_INITIAL_STATE=123456789
CONFIG_ENTROPY_DEVICE_RANDOM_GENERATOR=y
# CONFIG_XOSHIRO_RANDOM_GENERATOR is not set
CONFIG_CSPRNG_AVAILABLE=y
CONFIG_CSPRNG_ENABLED=y
CONFIG_HARDWARE_DEVICE_CS_GENERATOR=y
# CONFIG_CTR_DRBG_CSPRNG_GENERATOR is not set
# end of Random Number Generators

# CONFIG_RTIO is not set

#
# SD
#
# CONFIG_MMC_STACK is not set
# CONFIG_SDMMC_STACK is not set
# CONFIG_SDIO_STACK is not set
# end of SD

# CONFIG_SETTINGS is not set
# CONFIG_SHELL is not set
# CONFIG_STATS is not set

#
# Storage
#
# CONFIG_STREAM_FLASH is not set
# end of Storage

# CONFIG_TASK_WDT is not set

#
# Testing
#
# CONFIG_ZTEST is not set
# CONFIG_ZTEST_MOCKING is not set
# CONFIG_ZTRESS is not set
# CONFIG_TEST is not set
# CONFIG_FORCE_COVERAGE is not set
# CONFIG_TEST_USERSPACE is not set
# end of Testing

# CONFIG_TIMING_FUNCTIONS is not set
# CONFIG_TRACING is not set
# CONFIG_USB_DEVICE_STACK is not set
# CONFIG_USB_DEVICE_STACK_NEXT is not set
# CONFIG_USB_HOST_STACK is not set
# CONFIG_USBC_STACK is not set
# CONFIG_ZBUS is not set
# CONFIG_MODULES is not set
# end of Subsystems and OS Services

CONFIG_TOOLCHAIN_ZEPHYR_0_17=y
CONFIG_TOOLCHAIN_ZEPHYR_SUPPORTS_THREAD_LOCAL_STORAGE=y
CONFIG_TOOLCHAIN_ZEPHYR_SUPPORTS_GNU_EXTENSIONS=y

#
# Build and Link Features
#

#
# Linker Options
#
# CONFIG_LINKER_ORPHAN_SECTION_PLACE is not set
CONFIG_LINKER_ORPHAN_SECTION_WARN=y
# CONFIG_LINKER_ORPHAN_SECTION_ERROR is not set
CONFIG_FLASH_LOAD_SIZE=0x30000
CONFIG_ROM_END_OFFSET=0
CONFIG_LD_LINKER_SCRIPT_SUPPORTED=y
CONFIG_LD_LINKER_TEMPLATE=y
# CONFIG_CMAKE_LINKER_GENERATOR is not set
# CONFIG_HAVE_CUSTOM_LINKER_SCRIPT is not set
CONFIG_LINKER_SORT_BY_ALIGNMENT=y

#
# Linker Sections
#
# CONFIG_LINKER_USE_BOOT_SECTION is not set
# CONFIG_LINKER_USE_PINNED_SECTION is not set
CONFIG_LINKER_GENERIC_SECTIONS_PRESENT_AT_BOOT=y
CONFIG_LINKER_LAST_SECTION_ID=y
CONFIG_LINKER_LAST_SECTION_ID_PATTERN=0xE015E015
CONFIG_LINKER_USE_RELAX=y
# end of Linker Sections

CONFIG_LINKER_ITERABLE_SUBALIGN=4
CONFIG_LINKER_DEVNULL_SUPPORT=y
# CONFIG_LINKER_DEVNULL_MEMORY is not set
# end of Linker Options

#
# Compiler Options
#
# CONFIG_STD_C90 is not set
CONFIG_STD_C99=y
# CONFIG_STD_C11 is not set
# CONFIG_STD_C17 is not set
# CONFIG_STD_C23 is not set
CONFIG_TOOLCHAIN_SUPPORTS_GNU_EXTENSIONS=y
# CONFIG_GNU_C_EXTENSIONS is not set
# CONFIG_CODING_GUIDELINE_CHECK is not set
# CONFIG_COMPILER_FREESTANDING is not set
# CONFIG_SIZE_OPTIMIZATIONS is not set
# CONFIG_SIZE_OPTIMIZATIONS_AGGRESSIVE is not set
# CONFIG_SPEED_OPTIMIZATIONS is not set
CONFIG_DEBUG_OPTIMIZATIONS=y
# CONFIG_NO_OPTIMIZATIONS is not set
# CONFIG_COMPILER_WARNINGS_AS_ERRORS is not set
# CONFIG_DEPRECATION_TEST is not set
# CONFIG_COMPILER_SAVE_TEMPS is not set
CONFIG_COMPILER_TRACK_MACRO_EXPANSION=y
CONFIG_COMPILER_COLOR_DIAGNOSTICS=y
# CONFIG_FORTIFY_SOURCE_NONE is not set
CONFIG_FORTIFY_SOURCE_COMPILE_TIME=y
# CONFIG_FORTIFY_SOURCE_RUN_TIME is not set
CONFIG_COMPILER_OPT=""
# CONFIG_MISRA_SANE is not set
CONFIG_TOOLCHAIN_SUPPORTS_VLA_IN_STATEMENTS=y
# end of Compiler Options

# CONFIG_ASSERT_ON_ERRORS is not set
# CONFIG_NO_RUNTIME_CHECKS is not set
CONFIG_RUNTIME_ERROR_CHECKS=y

#
# Build Options
#
CONFIG_KERNEL_BIN_NAME="zephyr"
CONFIG_OUTPUT_STAT=y
# CONFIG_OUTPUT_SYMBOLS is not set
CONFIG_OUTPUT_PRINT_MEMORY_USAGE=y
# CONFIG_CLEANUP_INTERMEDIATE_FILES is not set
CONFIG_BUILD_GAP_FILL_PATTERN=0xFF
# CONFIG_BUILD_NO_GAP_FILL is not set
# CONFIG_BUILD_OUTPUT_HEX_GAP_FILL is not set
# CONFIG_BUILD_OUTPUT_EXE is not set
# CONFIG_BUILD_OUTPUT_S19_GAP_FILL is not set
# CONFIG_BUILD_OUTPUT_UF2 is not set
# CONFIG_BUILD_OUTPUT_MOT is not set
# CONFIG_BUILD_OUTPUT_STRIPPED is not set
# CONFIG_BUILD_OUTPUT_COMPRESS_DEBUG_SECTIONS is not set
# CONFIG_BUILD_ALIGN_LMA is not set
# CONFIG_APPLICATION_DEFINED_SYSCALL is not set
# CONFIG_MAKEFILE_EXPORTS is not set
# CONFIG_BUILD_OUTPUT_META is not set
CONFIG_BUILD_OUTPUT_STRIP_PATHS=y
CONFIG_CHECK_INIT_PRIORITIES=y
# CONFIG_EMIT_ALL_SYSCALLS is not set
# end of Build Options

CONFIG_WARN_DEPRECATED=y
CONFIG_EXPERIMENTAL=y
CONFIG_ENFORCE_ZEPHYR_STDINT=y
# end of Build and Link Features

#
# Boot Options
#
# CONFIG_IS_BOOTLOADER is not set
# CONFIG_BOOTLOADER_BOSSA is not set
# end of Boot Options

#
# Compatibility
#
CONFIG_LEGACY_GENERATED_INCLUDE_PATH=y
# end of Compatibility

# CONFIG_INPUT is not set
# CONFIG_WIFI is not set
# CONFIG_REGULATOR is not set
CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=2048
CONFIG_BT_LONG_WQ_STACK_SIZE=1024
CONFIG_MAIN_STACK_SIZE=2048
# CONFIG_FPU is not set
CONFIG_BT_RX_STACK_SIZE=768
CONFIG_SERIAL=y
# CONFIG_SPI is not set
# CONFIG_MIPI_DSI is not set
# CONFIG_MEMC is not set
# CONFIG_MODEM is not set
CONFIG_UART_INTERRUPT_DRIVEN=y
CONFIG_BT_HCI_ACL_FLOW_CONTROL=y
CONFIG_BT_HCI_VS=y
CONFIG_HW_STACK_PROTECTION=y
CONFIG_NUM_IRQS=48
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC=32768
CONFIG_FLASH_SIZE=1024
CONFIG_FLASH_BASE_ADDRESS=0x0
CONFIG_MP_MAX_NUM_CPUS=1
CONFIG_SOC_RESET_HOOK=y
CONFIG_CLOCK_CONTROL=y
CONFIG_IDLE_STACK_SIZE=320
CONFIG_ISR_STACK_SIZE=2048
CONFIG_SYS_CLOCK_TICKS_PER_SEC=32768
CONFIG_ROM_START_OFFSET=0
CONFIG_KERNEL_ENTRY="__start"
CONFIG_BUILD_OUTPUT_BIN=y
CONFIG_XIP=y
CONFIG_HAS_FLASH_LOAD_OFFSET=y
# CONFIG_COUNTER is not set
# CONFIG_SRAM_VECTOR_TABLE is not set
CONFIG_CPU_HAS_ARM_MPU=y
# CONFIG_SHARED_INTERRUPTS is not set
# CONFIG_PM_DEVICE is not set
CONFIG_TICKLESS_KERNEL=y
CONFIG_CLOCK_CONTROL_INIT_PRIORITY=30
# CONFIG_USE_DT_CODE_PARTITION is not set
# CONFIG_MULTI_LEVEL_INTERRUPTS is not set
CONFIG_ZERO_LATENCY_IRQS=y
CONFIG_ZERO_LATENCY_LEVELS=1
CONFIG_NUM_PREEMPT_PRIORITIES=15
CONFIG_NUM_METAIRQ_PRIORITIES=0
CONFIG_GEN_IRQ_VECTOR_TABLE=y
# CONFIG_DYNAMIC_INTERRUPTS is not set
CONFIG_GEN_ISR_TABLES=y
CONFIG_INIT_STACKS=y
CONFIG_TIMESLICE_SIZE=20
CONFIG_FLASH_LOAD_OFFSET=0
CONFIG_SYS_CLOCK_EXISTS=y
CONFIG_INIT_ARCH_HW_AT_BOOT=y
# CONFIG_BUILD_OUTPUT_S19 is not set
CONFIG_BUILD_OUTPUT_HEX=y
CONFIG_ARCH_HAS_CUSTOM_BUSY_WAIT=y
# CONFIG_FLASH is not set
# CONFIG_HCI_NXP_ENABLE_AUTO_SLEEP is not set
# CONFIG_HCI_NXP_SET_CAL_DATA is not set
CONFIG_BT_BUF_EVT_RX_COUNT=11
CONFIG_BT_BUF_ACL_TX_COUNT=10
# CONFIG_POWER_DOMAIN is not set
# CONFIG_MFD is not set
# CONFIG_HCI_NXP_RX_THREAD is not set
CONFIG_GPIO=y
# CONFIG_CPU_HAS_CUSTOM_FIXED_SOC_MPU_REGIONS is not set
# CONFIG_CODE_DATA_RELOCATION_SRAM is not set
# CONFIG_CACHE is not set
CONFIG_LOG=y
CONFIG_CMSIS_CORE_HAS_SYSTEM_CORE_CLOCK=y
# CONFIG_CODE_DATA_RELOCATION is not set
# CONFIG_ROMSTART_RELOCATION_ROM is not set
CONFIG_DCACHE_LINE_SIZE=32
# CONFIG_RESET is not set
CONFIG_ARCH_SW_ISR_TABLE_ALIGN=4
CONFIG_LOG_DOMAIN_NAME=""
CONFIG_ASSERT=y
CONFIG_LOG_PROCESS_THREAD_STACK_SIZE=1024
# CONFIG_DEVICE_DEPS is not set
CONFIG_SOC_HAS_TIMING_FUNCTIONS=y
# CONFIG_UART_USE_RUNTIME_CONFIGURE is not set
# CONFIG_SYSCON is not set
CONFIG_CONSOLE=y
# CONFIG_WINSTREAM is not set
CONFIG_COMMON_LIBC_MALLOC_ARENA_SIZE=-1
CONFIG_GEN_SW_ISR_TABLE=y
# CONFIG_REBOOT is not set
CONFIG_GEN_IRQ_START_VECTOR=0
CONFIG_SRAM_OFFSET=0
CONFIG_ARCH_IRQ_VECTOR_TABLE_ALIGN=4
CONFIG_ISR_TABLES_LOCAL_DECLARATION_SUPPORTED=y
# CONFIG_BOOTLOADER_MCUBOOT is not set
# CONFIG_SCHED_CPU_MASK is not set
CONFIG_KERNEL_MEM_POOL=y
CONFIG_MULTITHREADING=y
# CONFIG_OUTPUT_DISASSEMBLY is not set
# CONFIG_WATCHDOG is not set
CONFIG_ICACHE_LINE_SIZE=32
CONFIG_BT_BUF_CMD_TX_SIZE=255
CONFIG_BT_BUF_EVT_RX_SIZE=255
CONFIG_BT_BUF_ACL_TX_SIZE=251
CONFIG_BT_BUF_ACL_RX_SIZE=251

#
# Devicetree Info
#
CONFIG_DT_HAS_ARDUINO_UNO_ADC_ENABLED=y
CONFIG_DT_HAS_ARDUINO_HEADER_R3_ENABLED=y
CONFIG_DT_HAS_ARM_ARMV7M_ITM_ENABLED=y
CONFIG_DT_HAS_ARM_CORTEX_M4F_ENABLED=y
CONFIG_DT_HAS_ARM_CRYPTOCELL_310_ENABLED=y
CONFIG_DT_HAS_ARM_V7M_NVIC_ENABLED=y
CONFIG_DT_HAS_FIXED_PARTITIONS_ENABLED=y
CONFIG_DT_HAS_GPIO_KEYS_ENABLED=y
CONFIG_DT_HAS_GPIO_LEDS_ENABLED=y
CONFIG_DT_HAS_MMIO_SRAM_ENABLED=y
CONFIG_DT_HAS_NORDIC_BT_HCI_SDC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_ACL_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CCM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_CLOCK_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_ECB_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_EGU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_FICR_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPIOTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_GPREGRET_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_IEEE802154_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_MWU_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_NFCT_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_PINCTRL_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_POWER_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_PPI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_PWM_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_QSPI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_RADIO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_RNG_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SAADC_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SPI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SW_LPUART_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_SWI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_TEMP_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_TWI_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UARTE_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_UICR_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_USBD_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF_WDT_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF52_FLASH_CONTROLLER_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF52_HFXO_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF52X_REGULATOR_HV_ENABLED=y
CONFIG_DT_HAS_NORDIC_NRF5X_REGULATOR_ENABLED=y
CONFIG_DT_HAS_NORDIC_QSPI_NOR_ENABLED=y
CONFIG_DT_HAS_PWM_LEDS_ENABLED=y
CONFIG_DT_HAS_SOC_NV_FLASH_ENABLED=y
CONFIG_DT_HAS_ZEPHYR_RETENTION_ENABLED=y
# end of Devicetree Info

#
# Modules
#
# CONFIG_BUILD_ONLY_NO_BLOBS is not set

#
# Available modules.
#

#
# nrf (/opt/nordic/ncs/v3.1.1/nrf)
#
# CONFIG_NRF_802154_RADIO_DRIVER is not set
CONFIG_LOG_BUFFER_SIZE=4096
CONFIG_MPSL_WORK_STACK_SIZE=1024
# CONFIG_MBEDTLS is not set

#
# Nordic nRF Connect
#
CONFIG_WARN_EXPERIMENTAL=y
CONFIG_NORDIC_QSPI_NOR_FLASH_LAYOUT_PAGE_SIZE=4096
CONFIG_NRF_SECURITY_ENABLER=y
# CONFIG_NCS_SAMPLES_DEFAULTS is not set

#
# Image build variants
#
# CONFIG_NCS_MCUBOOT_IN_BUILD is not set
# end of Image build variants

# CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU_SPEEDUP is not set
CONFIG_BT_CTLR_DATA_LENGTH_MAX=251

#
# Subsystems
#

#
# Bootloader
#
# CONFIG_SECURE_BOOT is not set
CONFIG_PM_PARTITION_SIZE_PROVISION=0x1000
# CONFIG_B0_MIN_PARTITION_SIZE is not set
CONFIG_PM_PARTITION_SIZE_B0_IMAGE=0x8000
# CONFIG_IS_SECURE_BOOTLOADER is not set

#
# Secure Boot firmware validation
#
CONFIG_SB_VALIDATION_INFO_MAGIC=0x86518483
CONFIG_SB_VALIDATION_POINTER_MAGIC=0x6919b47e
CONFIG_SB_VALIDATION_INFO_CRYPTO_ID=1
CONFIG_SB_VALIDATION_INFO_VERSION=2
CONFIG_SB_VALIDATION_METADATA_OFFSET=0
CONFIG_SB_VALIDATION_STRUCT_HAS_HASH=y
CONFIG_SB_VALIDATION_STRUCT_HAS_PUBLIC_KEY=y
CONFIG_SB_VALIDATE_FW_SIGNATURE=y
# end of Secure Boot firmware validation

# CONFIG_SECURE_BOOT_STORAGE is not set
# CONFIG_MCUBOOT_COMPRESSED_IMAGE_SUPPORT_ENABLED is not set
# CONFIG_MCUBOOT_BOOTLOADER_SIGNATURE_TYPE_ED25519 is not set
# CONFIG_MCUBOOT_BOOTLOADER_SIGNATURE_TYPE_PURE is not set
# CONFIG_NCS_MCUBOOT_BOOTLOADER_SIGN_MERGED_BINARY is not set
# CONFIG_NCS_MCUBOOT_MANIFEST_UPDATES is not set
# end of Bootloader

#
# Bluetooth Low Energy
#
CONFIG_BT_COMPANY_ID_NORDIC=0x0059
CONFIG_BT_COMPANY_ID=0x0059
CONFIG_BT_MAX_CONN=2
CONFIG_BT_LL_SOFTDEVICE_HEADERS_INCLUDE=y
CONFIG_BT_LL_SOFTDEVICE=y

#
# SoftDevice Controller
#
CONFIG_BT_LL_SOFTDEVICE_BUILD_TYPE_LIB=y
CONFIG_BT_HCI_TX_STACK_SIZE=1536
# CONFIG_BT_CTLR_SDC_LLPM is not set
# CONFIG_BT_CTLR_SDC_QOS_CHANNEL_SURVEY is not set
# CONFIG_BT_CTLR_SDC_ALLOW_PARALLEL_SCANNING_AND_INITIATING is not set
CONFIG_BT_CTLR_SDC_PERIPHERAL_COUNT=1
# CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT_OVERRIDE is not set
CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT=4000000
CONFIG_BT_CTLR_SDC_CONN_EVENT_EXTEND_DEFAULT=y
CONFIG_BT_CTLR_SDC_CENTRAL_ACL_EVENT_SPACING_DEFAULT=4000000
# CONFIG_BT_CTLR_SDC_PERIODIC_ADV_EVENT_LEN_DEFAULT_OVERRIDE is not set
CONFIG_BT_CTLR_SDC_TX_PACKET_COUNT=10
CONFIG_BT_CTLR_SDC_RX_PACKET_COUNT=2
CONFIG_BT_CTLR_SDC_SCAN_BUFFER_COUNT=3
CONFIG_BT_CTLR_SDC_PERIODIC_SYNC_BUFFER_COUNT=3
CONFIG_BT_CTLR_SDC_RX_PRIO=6
# CONFIG_BT_CTLR_DF is not set
CONFIG_BT_LL_SOFTDEVICE_MULTIROLE=y
CONFIG_BT_CTLR_FAL_SIZE=8
# CONFIG_BT_CTLR_SDC_EVENT_TRIGGER is not set
# CONFIG_BT_CTLR_SDC_CONN_ANCHOR_POINT_REPORT is not set
# CONFIG_BT_CTLR_FRAME_SPACE_UPDATE is not set
# CONFIG_BT_CTLR_CHANNEL_SOUNDING is not set
# CONFIG_BT_CTLR_LE_PATH_LOSS_MONITORING is not set
# CONFIG_BT_CTLR_SDC_LE_POWER_CLASS_1 is not set
CONFIG_BT_LL_SOFTDEVICE_INIT_PRIORITY=40
# end of SoftDevice Controller

# CONFIG_BT_RADIO_NOTIFICATION_CONN_CB is not set

#
# BLE Libraries
#
# CONFIG_BT_GATT_POOL is not set
# CONFIG_BT_GATT_DM is not set
# CONFIG_BT_ADV_PROV is not set
# CONFIG_BT_SCAN is not set
# CONFIG_BT_CONN_CTX is not set

#
# Bluetooth Services
#
# CONFIG_BT_AMS_CLIENT is not set
# CONFIG_BT_ANCS_CLIENT is not set
# CONFIG_BT_BAS_CLIENT is not set
# CONFIG_BT_BMS is not set
# CONFIG_BT_CTS_CLIENT is not set
# CONFIG_BT_DFU_SMP is not set
# CONFIG_BT_GATTP is not set
# CONFIG_BT_HIDS is not set
# CONFIG_BT_HOGP is not set
# CONFIG_BT_LBS is not set
# CONFIG_BT_NSMS is not set
# CONFIG_BT_NUS is not set
# CONFIG_BT_NUS_CLIENT is not set
# CONFIG_BT_RSCS is not set
# CONFIG_BT_THROUGHPUT is not set
# CONFIG_BT_LATENCY is not set
# CONFIG_BT_LATENCY_CLIENT is not set
# CONFIG_BT_HRS_CLIENT is not set
# CONFIG_BT_DDFS is not set
# CONFIG_BT_MDS is not set
# CONFIG_BT_CGMS is not set
# CONFIG_BT_FAST_PAIR is not set
CONFIG_SYSTEM_WORKQUEUE_PRIORITY=-1
# end of Bluetooth Services

#
# BLE over nRF RPC
#
CONFIG_HEAP_MEM_POOL_SIZE=0
# CONFIG_BT_SHELL is not set
CONFIG_BT_CONN_DYNAMIC_CALLBACKS=y
# CONFIG_BT_RPC_STACK is not set
CONFIG_BT_CENTRAL=y
CONFIG_BT_PERIPHERAL=y
CONFIG_BT_OBSERVER=y
CONFIG_BT_BROADCASTER=y
CONFIG_BT_CONN=y
CONFIG_BT_REMOTE_VERSION=y
CONFIG_BT_PHY_UPDATE=y
CONFIG_BT_DATA_LEN_UPDATE=y
# CONFIG_BT_EXT_ADV is not set
CONFIG_BT_LOG=y
# CONFIG_BT_LOG_LEVEL_OFF is not set
# CONFIG_BT_LOG_LEVEL_ERR is not set
# CONFIG_BT_LOG_LEVEL_WRN is not set
# CONFIG_BT_LOG_LEVEL_INF is not set
# CONFIG_BT_LOG_LEVEL_DBG is not set
CONFIG_BT_LOG_LEVEL_DEFAULT=y
CONFIG_BT_LOG_LEVEL=3
CONFIG_BT_HCI_DRIVER_LOG_LEVEL_INHERIT=y
CONFIG_BT_HCI_DRIVER_LOG_LEVEL=3
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_OFF is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_ERR is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_WRN is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_INF is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_DBG is not set
# CONFIG_BT_HCI_DRIVER_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_RPA_LOG_LEVEL_INHERIT=y
CONFIG_BT_RPA_LOG_LEVEL=3
# CONFIG_BT_RPA_LOG_LEVEL_OFF is not set
# CONFIG_BT_RPA_LOG_LEVEL_ERR is not set
# CONFIG_BT_RPA_LOG_LEVEL_WRN is not set
# CONFIG_BT_RPA_LOG_LEVEL_INF is not set
# CONFIG_BT_RPA_LOG_LEVEL_DBG is not set
# CONFIG_BT_RPA_LOG_LEVEL_DEFAULT is not set
CONFIG_BT_BUF_ACL_RX_COUNT_EXTRA=2
CONFIG_BT_HAS_HCI_VS=y
# CONFIG_BT_HCI_MESH_EXT is not set
# CONFIG_BT_WAIT_NOP is not set
CONFIG_BT_RPA=y
CONFIG_BT_ASSERT=y
CONFIG_BT_ASSERT_VERBOSE=y
# CONFIG_BT_ASSERT_PANIC is not set
# CONFIG_BT_HCI_ERR_TO_STR is not set
CONFIG_BT_DEBUG_NONE=y
# CONFIG_BT_DEBUG_MONITOR_UART is not set
# CONFIG_BT_DEBUG_MONITOR_RTT is not set
# CONFIG_BT_LONG_WQ is not set
# CONFIG_BT_HCI_TX_STACK_SIZE_WITH_PROMPT is not set
CONFIG_BT_HCI_TX_PRIO=7
# CONFIG_BT_RECV_WORKQ_SYS is not set
CONFIG_BT_RECV_WORKQ_BT=y
CONFIG_BT_RX_PRIO=8
CONFIG_BT_DRIVER_RX_HIGH_PRIO=6
# CONFIG_BT_CONN_TX_NOTIFY_WQ is not set
# CONFIG_BT_HOST_CCM is not set
# CONFIG_BT_LOG_SNIFFER_INFO is not set
# CONFIG_BT_TESTING is not set
# CONFIG_BT_HCI_VS_EVT_USER is not set
# end of BLE over nRF RPC
# end of Bluetooth Low Energy

#
# DFU
#
# CONFIG_DFU_MULTI_IMAGE is not set
# CONFIG_DFU_TARGET is not set
# end of DFU

# CONFIG_ESB is not set

#
# Peripheral CPU DFU (PCD)
#
# CONFIG_PCD is not set
# CONFIG_PCD_APP is not set
CONFIG_PCD_VERSION_PAGE_BUF_SIZE=2046
# CONFIG_PCD_NET is not set
# end of Peripheral CPU DFU (PCD)

#
# Networking
#

#
# Application protocols
#
# CONFIG_NRF_CLOUD is not set
# CONFIG_REST_CLIENT is not set
# CONFIG_DOWNLOADER is not set
# CONFIG_AWS_IOT is not set
# CONFIG_AWS_JOBS is not set
# CONFIG_AZURE_IOT_HUB is not set

#
# Self-Registration (Zi ZHu Ce)
#
# end of Self-Registration (Zi ZHu Ce)

# CONFIG_ICAL_PARSER is not set
# CONFIG_FTP_CLIENT is not set
# CONFIG_LWM2M_CLIENT_UTILS is not set
# CONFIG_MQTT_HELPER is not set
# CONFIG_NRF_MCUMGR_SMP_CLIENT is not set
# CONFIG_WIFI_PROV_CORE_LOG_LEVEL_OFF is not set
# CONFIG_WIFI_PROV_CORE_LOG_LEVEL_ERR is not set
# CONFIG_WIFI_PROV_CORE_LOG_LEVEL_WRN is not set
# CONFIG_WIFI_PROV_CORE_LOG_LEVEL_INF is not set
# CONFIG_WIFI_PROV_CORE_LOG_LEVEL_DBG is not set
CONFIG_WIFI_PROV_CORE_LOG_LEVEL_DEFAULT=y
CONFIG_WIFI_PROV_CORE_LOG_LEVEL=3
# end of Application protocols

# CONFIG_OPENTHREAD_RPC is not set
# end of Networking

#
# NFC
#
# CONFIG_NFC_NDEF is not set
# CONFIG_NFC_NDEF_PARSER is not set
# CONFIG_NFC_NDEF_PAYLOAD_TYPE_COMMON is not set
# CONFIG_NFC_T2T_PARSER is not set
# CONFIG_NFC_T4T_NDEF_FILE is not set
# CONFIG_NFC_T4T_ISODEP is not set
# CONFIG_NFC_T4T_APDU is not set
# CONFIG_NFC_T4T_CC_FILE is not set
# CONFIG_NFC_T4T_HL_PROCEDURE is not set
# CONFIG_NFC_PLATFORM is not set
# CONFIG_NFC_TNEP_TAG is not set
# CONFIG_NFC_TNEP_POLLER is not set
# CONFIG_NFC_TNEP_CH is not set
# CONFIG_NFC_RPC is not set
# end of NFC

# CONFIG_APP_EVENT_MANAGER is not set
# CONFIG_NRF_PROFILER is not set
# CONFIG_FW_INFO is not set

#
# Debug
#
# CONFIG_NRF_CPU_LOAD is not set
# CONFIG_PPI_TRACE is not set
CONFIG_PPI_TRACE_PIN_CNT=8
# end of Debug

# CONFIG_SHELL_BT_NUS is not set

#
# Multiprotocol service layer (MPSL)
#
# CONFIG_MPSL_FEM_ONLY is not set
CONFIG_MPSL_FEM_API_AVAILABLE=y
# CONFIG_MPSL_FEM_DEVICE_CONFIG_254 is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_OFF is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_ERR is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_WRN is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_INF is not set
# CONFIG_MPSL_FEM_LOG_LEVEL_DBG is not set
CONFIG_MPSL_FEM_LOG_LEVEL_DEFAULT=y
CONFIG_MPSL_FEM_LOG_LEVEL=3
CONFIG_MPSL_THREAD_COOP_PRIO=6
CONFIG_MPSL_TIMESLOT_SESSION_COUNT=0
# CONFIG_MPSL_ASSERT_HANDLER is not set
CONFIG_MPSL_LOW_PRIO_IRQN=25
CONFIG_MPSL_HFCLK_LATENCY=1400
CONFIG_MPSL_INIT_PRIORITY=40
# CONFIG_MPSL_LOG_LEVEL_OFF is not set
# CONFIG_MPSL_LOG_LEVEL_ERR is not set
# CONFIG_MPSL_LOG_LEVEL_WRN is not set
# CONFIG_MPSL_LOG_LEVEL_INF is not set
# CONFIG_MPSL_LOG_LEVEL_DBG is not set
CONFIG_MPSL_LOG_LEVEL_DEFAULT=y
CONFIG_MPSL_LOG_LEVEL=3
# CONFIG_MPSL_PIN_DEBUG is not set
# CONFIG_MPSL_USE_EXTERNAL_CLOCK_CONTROL is not set
# end of Multiprotocol service layer (MPSL)

#
# Partition Manager
#
CONFIG_PARTITION_MANAGER_ENABLED=y
CONFIG_FLASH_MAP_CUSTOM=y
CONFIG_SRAM_SIZE=256
CONFIG_SRAM_BASE_ADDRESS=0x20000000

#
# Zephyr subsystem configurations
#
# end of Zephyr subsystem configurations

#
# NCS subsystem configurations
#
CONFIG_PM_EXTERNAL_FLASH_BASE=0
CONFIG_PM_EXTERNAL_FLASH_PATH=""
CONFIG_PM_EXTERNAL_FLASH_SIZE_BITS=0
# CONFIG_PM_OVERRIDE_EXTERNAL_DRIVER_CHECK is not set
CONFIG_PM_SRAM_BASE=0x20000000
CONFIG_PM_SRAM_SIZE=0x40000
# end of Partition Manager

#
# nRF RPC (Remote Procedure Call) library
#
# end of nRF RPC (Remote Procedure Call) library

#
# Full Modem Firmware Update Management(FMFU)
#
# end of Full Modem Firmware Update Management(FMFU)

#
# Additional MCUmgr configuration
#

#
# Additional MCUmgr group configuration
#

#
# Additional MCUmgr OS group management functionality
#
# end of Additional MCUmgr OS group management functionality

#
# Additional MCUmgr image management group functionality
#
# end of Additional MCUmgr image management group functionality
# end of Additional MCUmgr group configuration
# end of Additional MCUmgr configuration

# CONFIG_CAF is not set
# CONFIG_DM_MODULE is not set

#
# nRF Security
#
# CONFIG_NORDIC_SECURITY_BACKEND is not set
# CONFIG_NRF_SECURITY is not set

#
# Nordic-added meta types
#

#
# Nordic added alg types
#
# CONFIG_PSA_WANT_ALG_ECDSA_ANY is not set
# CONFIG_PSA_WANT_ALG_ED25519PH is not set
# CONFIG_PSA_WANT_ALG_ED448PH is not set
# CONFIG_PSA_WANT_ALG_HSS is not set
# CONFIG_PSA_WANT_ALG_LMS is not set
# CONFIG_PSA_WANT_ALG_ML_DSA is not set
# CONFIG_PSA_WANT_ALG_XMSS is not set
# CONFIG_PSA_WANT_ALG_XMSS_MT is not set
# CONFIG_PSA_WANT_ALG_ML_KEM is not set
# CONFIG_PSA_WANT_ALG_PURE_EDDSA is not set
# CONFIG_PSA_WANT_ALG_RSA_PKCS1V15_SIGN_RAW is not set
# CONFIG_PSA_WANT_ALG_RSA_PSS_ANY_SALT is not set
# CONFIG_PSA_WANT_ALG_SHA_256_192 is not set
# CONFIG_PSA_WANT_ALG_SHA_512_224 is not set
# CONFIG_PSA_WANT_ALG_SHA_512_256 is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_HMAC is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_CMAC is not set
# CONFIG_PSA_WANT_ALG_SPAKE2P_MATTER is not set
# CONFIG_PSA_WANT_ALG_SRP_6 is not set
# CONFIG_PSA_WANT_ALG_SRP_PASSWORD_HASH is not set
# CONFIG_PSA_WANT_ALG_XTS is not set
# CONFIG_PSA_WANT_ALG_ECB_NO_PADDING is not set
# CONFIG_PSA_WANT_ALG_CHACHA20 is not set
# CONFIG_PSA_WANT_ALG_XCHACHA20_POLY1305 is not set
# CONFIG_PSA_WANT_ALG_SHAKE128_256 is not set
# CONFIG_PSA_WANT_ALG_SHAKE256_192 is not set
# CONFIG_PSA_WANT_ALG_SHAKE256_256 is not set
# CONFIG_PSA_WANT_ALG_SHAKE256_512 is not set
# CONFIG_PSA_WANT_ALG_AES_KW is not set
# CONFIG_PSA_WANT_ALG_AES_KWP is not set
# CONFIG_PSA_WANT_ALG_WPA3_SAE_H2E is not set
# CONFIG_PSA_WANT_ALG_WPA3_SAE is not set

#
# Nordic added ECC curve types
#
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_224 is not set
# CONFIG_PSA_WANT_ECC_BRAINPOOL_P_R1_320 is not set
# CONFIG_PSA_WANT_ECC_TWISTED_EDWARDS_255 is not set
# CONFIG_PSA_WANT_ECC_TWISTED_EDWARDS_448 is not set
# CONFIG_PSA_WANT_ECC_SECP_K1_224 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_233 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_283 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_409 is not set
# CONFIG_PSA_WANT_ECC_SECT_R1_571 is not set

#
# Nordic addded RNG configuration
#
# CONFIG_PSA_WANT_GENERATE_RANDOM is not set

#
# Nordic added key types
#
# CONFIG_PSA_WANT_KEY_TYPE_PEPPER is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SPAKE2P_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_SRP_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_WPA3_SAE_PT is not set
# CONFIG_PSA_WANT_KEY_TYPE_XCHACHA20 is not set
# CONFIG_PSA_WANT_KEY_TYPE_HSS_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_LMS_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_XMSS_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_KEY_TYPE_XMSS_MT_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_ML_DSA_KEY_SIZE_44 is not set
# CONFIG_PSA_WANT_ML_DSA_KEY_SIZE_65 is not set
# CONFIG_PSA_WANT_ML_DSA_KEY_SIZE_87 is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_DSA_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_DSA_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_DSA_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_DSA_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_DSA_PUBLIC_KEY is not set
# CONFIG_PSA_WANT_ML_KEM_KEY_SIZE_512 is not set
# CONFIG_PSA_WANT_ML_KEM_KEY_SIZE_768 is not set
# CONFIG_PSA_WANT_ML_KEM_KEY_SIZE_1024 is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_KEM_KEY_PAIR_IMPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_KEM_KEY_PAIR_EXPORT is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_KEM_KEY_PAIR_GENERATE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_KEM_KEY_PAIR_DERIVE is not set
# CONFIG_PSA_WANT_KEY_TYPE_ML_KEM_PUBLIC_KEY is not set
# end of nRF Security

#
# Audio Modules
#
# CONFIG_AUDIO_MODULE_TEST is not set

#
# Log levels
#
# end of Log levels
# end of Audio Modules

#
# Audio Modules
#
# CONFIG_AUDIO_MODULE_TEMPLATE is not set
# end of Audio Modules

# CONFIG_UART_ASYNC_ADAPTER is not set
# CONFIG_TRUSTED_STORAGE is not set

#
# Logging over RPC
#
# CONFIG_LOG_FORWARDER_RPC is not set
# CONFIG_LOG_BACKEND_RPC is not set
CONFIG_LOG_BACKED_RPC_CRASH_INFO_FILENAME_SIZE=255
# end of Logging over RPC

# CONFIG_DULT is not set
# CONFIG_NRF_COMPRESS is not set

#
# MCUboot IDs (informative only, do not change)
#
CONFIG_MCUBOOT_APPLICATION_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_NETWORK_CORE_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_WIFI_PATCHES_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_QSPI_XIP_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_MCUBOOT_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_EXTRA_1_IMAGE_NUMBER=-1
CONFIG_MCUBOOT_EXTRA_2_IMAGE_NUMBER=-1
# end of MCUboot IDs (informative only, do not change)
# end of Subsystems

# CONFIG_WFA_QT_LOG_LEVEL_OFF is not set
# CONFIG_WFA_QT_LOG_LEVEL_ERR is not set
# CONFIG_WFA_QT_LOG_LEVEL_WRN is not set
# CONFIG_WFA_QT_LOG_LEVEL_INF is not set
# CONFIG_WFA_QT_LOG_LEVEL_DBG is not set
CONFIG_WFA_QT_LOG_LEVEL_DEFAULT=y
CONFIG_WFA_QT_LOG_LEVEL=3
# CONFIG_WFA_QT_CONTROL_APP is not set
CONFIG_WFA_QT_THREAD_STACK_SIZE=5200
CONFIG_WFA_QT_REBOOT_TIMEOUT_MS=1000
CONFIG_WFA_QT_DEFAULT_INTERFACE="wlan0"
CONFIG_WPAS_READY_TIMEOUT_MS=10000

#
# Libraries
#
# CONFIG_APP_JWT is not set

#
# Binary libraries
#
# end of Binary libraries

# CONFIG_AT_MONITOR is not set
# CONFIG_LTE_LINK_CONTROL is not set
CONFIG_NRF_ACL_FLASH_REGION_SIZE=0x1000
CONFIG_FPROTECT_BLOCK_SIZE=0x1000
# CONFIG_FPROTECT is not set
# CONFIG_AT_CMD_CUSTOM is not set
# CONFIG_DK_LIBRARY is not set
# CONFIG_AT_PARSER is not set
CONFIG_MULTITHREADING_LOCK=y
# CONFIG_RESET_ON_FATAL_ERROR is not set
# CONFIG_SMS is not set
# CONFIG_SUPL_CLIENT_LIB is not set
# CONFIG_DATE_TIME is not set
# CONFIG_HW_ID_LIBRARY is not set
# CONFIG_RAM_POWER_DOWN_LIBRARY is not set
# CONFIG_WAVE_GEN_LIB is not set
# CONFIG_HW_UNIQUE_KEY_LOAD is not set
CONFIG_HW_UNIQUE_KEY_SUPPORTED=y
CONFIG_HW_UNIQUE_KEY_PARTITION_SIZE=0x1000
# CONFIG_LOCATION is not set
# CONFIG_QOS is not set
# CONFIG_SFLOAT is not set
# CONFIG_CONTIN_ARRAY is not set
# CONFIG_PCM_MIX is not set
# CONFIG_TONE is not set
# CONFIG_PSCM is not set
# CONFIG_DATA_FIFO is not set
# CONFIG_FEM_AL_LIB is not set
# CONFIG_SAMPLE_RATE_CONVERTER is not set
CONFIG_NCS_BOOT_BANNER=y
CONFIG_NCS_NCS_BOOT_BANNER_STRING="nRF Connect SDK"
CONFIG_NCS_ZEPHYR_BOOT_BANNER_STRING="Zephyr OS"
# end of Libraries

#
# Device Drivers
#
# CONFIG_BT_DRIVER_QUIRK_NO_AUTO_DLE is not set
CONFIG_ENTROPY_CC3XX=y
# CONFIG_FLASH_RPC is not set
CONFIG_HW_CC3XX=y
CONFIG_CLOCK_CONTROL_MPSL=y
CONFIG_SOC_FLASH_NRF_RADIO_SYNC_MPSL_TIMESLOT_SESSION_COUNT=0
# CONFIG_ETH_RTT is not set
# CONFIG_SENSOR is not set
CONFIG_NRF_SW_LPUART=y
CONFIG_NRFX_GPIOTE_NUM_OF_EVT_HANDLERS=2
CONFIG_NRF_SW_LPUART_INIT_PRIORITY=45
CONFIG_NRF_SW_LPUART_HFXO_ON_RX=y
CONFIG_NRF_SW_LPUART_MAX_PACKET_SIZE=128
CONFIG_NRF_SW_LPUART_DEFAULT_TX_TIMEOUT=1000000
CONFIG_NRF_SW_LPUART_INT_DRIVEN=y
CONFIG_NRF_SW_LPUART_INT_DRV_TX_BUF_SIZE=128
# CONFIG_NRF_SW_LPUART_LOG_LEVEL_OFF is not set
# CONFIG_NRF_SW_LPUART_LOG_LEVEL_ERR is not set
# CONFIG_NRF_SW_LPUART_LOG_LEVEL_WRN is not set
# CONFIG_NRF_SW_LPUART_LOG_LEVEL_INF is not set
# CONFIG_NRF_SW_LPUART_LOG_LEVEL_DBG is not set
CONFIG_NRF_SW_LPUART_LOG_LEVEL_DEFAULT=y
CONFIG_NRF_SW_LPUART_LOG_LEVEL=3
# end of Device Drivers

#
# External libraries
#
# end of External libraries

#
# Test
#
# CONFIG_UNITY is not set

#
# Mocks
#
# CONFIG_MOCK_NRF_MODEM_AT is not set
# CONFIG_MOCK_NRF_RPC is not set
# end of Mocks
# end of Test
# end of Nordic nRF Connect

CONFIG_ZEPHYR_NRF_MODULE=y
# end of nrf (/opt/nordic/ncs/v3.1.1/nrf)

#
# hostap (/opt/nordic/ncs/v3.1.1/modules/lib/hostap)
#
# CONFIG_WIFI_NM_WPA_SUPPLICANT is not set
CONFIG_ZEPHYR_HOSTAP_MODULE=y
# end of hostap (/opt/nordic/ncs/v3.1.1/modules/lib/hostap)

#
# mcuboot (/opt/nordic/ncs/v3.1.1/bootloader/mcuboot)
#

#
# MCUboot
#
CONFIG_DT_FLASH_WRITE_BLOCK_SIZE=4
CONFIG_MCUBOOT_USB_SUPPORT=y
# CONFIG_USE_NRF53_MULTI_IMAGE_WITHOUT_UPGRADE_ONLY is not set
# end of MCUboot

CONFIG_ZEPHYR_MCUBOOT_MODULE=y
# end of mcuboot (/opt/nordic/ncs/v3.1.1/bootloader/mcuboot)

#
# mbedtls (/opt/nordic/ncs/v3.1.1/modules/crypto/mbedtls)
#
CONFIG_ZEPHYR_MBEDTLS_MODULE=y
# CONFIG_PSA_CRYPTO is not set
# end of mbedtls (/opt/nordic/ncs/v3.1.1/modules/crypto/mbedtls)

#
# oberon-psa-crypto (/opt/nordic/ncs/v3.1.1/modules/crypto/oberon-psa-crypto)
#
CONFIG_ZEPHYR_OBERON_PSA_CRYPTO_MODULE=y
# end of oberon-psa-crypto (/opt/nordic/ncs/v3.1.1/modules/crypto/oberon-psa-crypto)

#
# trusted-firmware-m (/opt/nordic/ncs/v3.1.1/modules/tee/tf-m/trusted-firmware-m)
#
CONFIG_ZEPHYR_TRUSTED_FIRMWARE_M_MODULE=y
# end of trusted-firmware-m (/opt/nordic/ncs/v3.1.1/modules/tee/tf-m/trusted-firmware-m)

CONFIG_ZEPHYR_PSA_ARCH_TESTS_MODULE=y

#
# cjson (/opt/nordic/ncs/v3.1.1/modules/lib/cjson)
#
# CONFIG_CJSON_LIB is not set
CONFIG_ZEPHYR_CJSON_MODULE=y
# end of cjson (/opt/nordic/ncs/v3.1.1/modules/lib/cjson)

#
# azure-sdk-for-c (/opt/nordic/ncs/v3.1.1/modules/lib/azure-sdk-for-c)
#
# CONFIG_AZURE_SDK is not set
CONFIG_ZEPHYR_AZURE_SDK_FOR_C_MODULE=y
# end of azure-sdk-for-c (/opt/nordic/ncs/v3.1.1/modules/lib/azure-sdk-for-c)

#
# cirrus-logic (/opt/nordic/ncs/v3.1.1/modules/hal/cirrus-logic)
#
# CONFIG_HW_CODEC_CIRRUS_LOGIC is not set
CONFIG_ZEPHYR_CIRRUS_LOGIC_MODULE=y
# end of cirrus-logic (/opt/nordic/ncs/v3.1.1/modules/hal/cirrus-logic)

#
# openthread (/opt/nordic/ncs/v3.1.1/modules/lib/openthread)
#
# CONFIG_OPENTHREAD is not set
CONFIG_ZEPHYR_OPENTHREAD_MODULE=y
# end of openthread (/opt/nordic/ncs/v3.1.1/modules/lib/openthread)

#
# memfault-firmware-sdk (/opt/nordic/ncs/v3.1.1/modules/lib/memfault-firmware-sdk)
#
# CONFIG_MEMFAULT is not set
CONFIG_ZEPHYR_MEMFAULT_FIRMWARE_SDK_MODULE=y
# end of memfault-firmware-sdk (/opt/nordic/ncs/v3.1.1/modules/lib/memfault-firmware-sdk)

#
# coremark (/opt/nordic/ncs/v3.1.1/modules/benchmark/coremark)
#
# CONFIG_COREMARK is not set
CONFIG_ZEPHYR_COREMARK_MODULE=y
# end of coremark (/opt/nordic/ncs/v3.1.1/modules/benchmark/coremark)

#
# canopennode (/opt/nordic/ncs/v3.1.1/modules/lib/canopennode)
#
CONFIG_ZEPHYR_CANOPENNODE_MODULE=y
# end of canopennode (/opt/nordic/ncs/v3.1.1/modules/lib/canopennode)

#
# chre (/opt/nordic/ncs/v3.1.1/modules/lib/chre)
#
CONFIG_ZEPHYR_CHRE_MODULE=y
# CONFIG_CHRE is not set
# end of chre (/opt/nordic/ncs/v3.1.1/modules/lib/chre)

#
# lz4 (/opt/nordic/ncs/v3.1.1/modules/lib/lz4)
#
CONFIG_ZEPHYR_LZ4_MODULE=y
# CONFIG_LZ4 is not set
# end of lz4 (/opt/nordic/ncs/v3.1.1/modules/lib/lz4)

CONFIG_ZEPHYR_TF_M_TESTS_MODULE=y

#
# zscilib (/opt/nordic/ncs/v3.1.1/modules/lib/zscilib)
#
# CONFIG_ZSL is not set
CONFIG_ZEPHYR_ZSCILIB_MODULE=y
# end of zscilib (/opt/nordic/ncs/v3.1.1/modules/lib/zscilib)

#
# cmsis (/opt/nordic/ncs/v3.1.1/modules/hal/cmsis)
#
CONFIG_ZEPHYR_CMSIS_MODULE=y
CONFIG_HAS_CMSIS_CORE=y
# end of cmsis (/opt/nordic/ncs/v3.1.1/modules/hal/cmsis)

#
# cmsis-dsp (/opt/nordic/ncs/v3.1.1/modules/lib/cmsis-dsp)
#
CONFIG_ZEPHYR_CMSIS_DSP_MODULE=y
# CONFIG_CMSIS_DSP is not set
# end of cmsis-dsp (/opt/nordic/ncs/v3.1.1/modules/lib/cmsis-dsp)

#
# cmsis-nn (/opt/nordic/ncs/v3.1.1/modules/lib/cmsis-nn)
#
CONFIG_ZEPHYR_CMSIS_NN_MODULE=y
# CONFIG_CMSIS_NN is not set
# end of cmsis-nn (/opt/nordic/ncs/v3.1.1/modules/lib/cmsis-nn)

#
# cmsis_6 (/opt/nordic/ncs/v3.1.1/modules/hal/cmsis_6)
#
CONFIG_ZEPHYR_CMSIS_6_MODULE=y
CONFIG_HAS_CMSIS_CORE_M=y
# CONFIG_CMSIS_M_CHECK_DEVICE_DEFINES is not set
# end of cmsis_6 (/opt/nordic/ncs/v3.1.1/modules/hal/cmsis_6)

#
# fatfs (/opt/nordic/ncs/v3.1.1/modules/fs/fatfs)
#
CONFIG_ZEPHYR_FATFS_MODULE=y
# end of fatfs (/opt/nordic/ncs/v3.1.1/modules/fs/fatfs)

#
# hal_nordic (/opt/nordic/ncs/v3.1.1/modules/hal/nordic)
#
CONFIG_ZEPHYR_HAL_NORDIC_MODULE=y
CONFIG_HAS_NORDIC_DRIVERS=y

#
# Nordic drivers
#
# CONFIG_NRF_802154_SOURCE_HAL_NORDIC is not set
# CONFIG_NRF_802154_SER_RADIO is not set
# end of Nordic drivers

CONFIG_HAS_NRFX=y

#
# nrfx drivers
#

#
# nrfx drivers logging
#
# CONFIG_NRFX_GPIOTE_LOG is not set
# CONFIG_NRFX_TIMER_LOG is not set
# end of nrfx drivers logging

# CONFIG_NRFX_CLOCK is not set
# CONFIG_NRFX_COMP is not set
# CONFIG_NRFX_EGU0 is not set
# CONFIG_NRFX_EGU1 is not set
# CONFIG_NRFX_EGU2 is not set
# CONFIG_NRFX_EGU3 is not set
# CONFIG_NRFX_EGU4 is not set
# CONFIG_NRFX_EGU5 is not set
CONFIG_NRFX_GPIOTE=y
CONFIG_NRFX_GPIOTE0=y
CONFIG_NRFX_GPPI=y
# CONFIG_NRFX_GPPI_V1 is not set
# CONFIG_NRFX_I2S is not set
# CONFIG_NRFX_LPCOMP is not set
# CONFIG_NRFX_NFCT is not set
# CONFIG_NRFX_NVMC is not set
# CONFIG_NRFX_PDM is not set
# CONFIG_NRFX_POWER is not set
# CONFIG_NRFX_PWM is not set
# CONFIG_NRFX_QDEC is not set
# CONFIG_NRFX_QSPI is not set
# CONFIG_NRFX_RNG is not set
# CONFIG_NRFX_RTC0 is not set
# CONFIG_NRFX_RTC1 is not set
# CONFIG_NRFX_RTC2 is not set
# CONFIG_NRFX_SAADC is not set
# CONFIG_NRFX_SPI0 is not set
# CONFIG_NRFX_SPI1 is not set
# CONFIG_NRFX_SPI2 is not set
# CONFIG_NRFX_SPIM is not set
# CONFIG_NRFX_SYSTICK is not set
# CONFIG_NRFX_TEMP is not set
CONFIG_NRFX_TIMER=y
# CONFIG_NRFX_TWI0 is not set
# CONFIG_NRFX_TWI1 is not set
# CONFIG_NRFX_TWIM is not set
# CONFIG_NRFX_TWIS is not set
# CONFIG_NRFX_UART0 is not set
# CONFIG_NRFX_UARTE is not set

#
# Peripheral Resource Sharing module
#
# CONFIG_NRFX_PRS_BOX_0 is not set
# CONFIG_NRFX_PRS_BOX_1 is not set
# CONFIG_NRFX_PRS_BOX_2 is not set
# CONFIG_NRFX_PRS_BOX_3 is not set
# CONFIG_NRFX_PRS_BOX_4 is not set
# end of Peripheral Resource Sharing module

CONFIG_NRFX_RESERVED_RESOURCES_HEADER="nrfx_reserved_resources_ncs.h"
# end of nrfx drivers
# end of hal_nordic (/opt/nordic/ncs/v3.1.1/modules/hal/nordic)

#
# hal_st (/opt/nordic/ncs/v3.1.1/modules/hal/st)
#
CONFIG_ZEPHYR_HAL_ST_MODULE=y
# end of hal_st (/opt/nordic/ncs/v3.1.1/modules/hal/st)

#
# hal_tdk (/opt/nordic/ncs/v3.1.1/modules/hal/tdk)
#
CONFIG_ZEPHYR_HAL_TDK_MODULE=y

#
# TDK drivers
#
# CONFIG_TDK_HAL is not set
# end of TDK drivers
# end of hal_tdk (/opt/nordic/ncs/v3.1.1/modules/hal/tdk)

CONFIG_ZEPHYR_HAL_WURTHELEKTRONIK_MODULE=y

#
# liblc3 (/opt/nordic/ncs/v3.1.1/modules/lib/liblc3)
#
CONFIG_ZEPHYR_LIBLC3_MODULE=y
# end of liblc3 (/opt/nordic/ncs/v3.1.1/modules/lib/liblc3)

CONFIG_ZEPHYR_LIBMETAL_MODULE=y

#
# littlefs (/opt/nordic/ncs/v3.1.1/modules/fs/littlefs)
#
CONFIG_ZEPHYR_LITTLEFS_MODULE=y
# end of littlefs (/opt/nordic/ncs/v3.1.1/modules/fs/littlefs)

#
# loramac-node (/opt/nordic/ncs/v3.1.1/modules/lib/loramac-node)
#
CONFIG_ZEPHYR_LORAMAC_NODE_MODULE=y
# CONFIG_HAS_SEMTECH_RADIO_DRIVERS is not set
# end of loramac-node (/opt/nordic/ncs/v3.1.1/modules/lib/loramac-node)

#
# lvgl (/opt/nordic/ncs/v3.1.1/modules/lib/gui/lvgl)
#
CONFIG_ZEPHYR_LVGL_MODULE=y
# end of lvgl (/opt/nordic/ncs/v3.1.1/modules/lib/gui/lvgl)

CONFIG_ZEPHYR_MIPI_SYS_T_MODULE=y

#
# nanopb (/opt/nordic/ncs/v3.1.1/modules/lib/nanopb)
#
CONFIG_ZEPHYR_NANOPB_MODULE=y
# CONFIG_NANOPB is not set
# end of nanopb (/opt/nordic/ncs/v3.1.1/modules/lib/nanopb)

#
# nrf_wifi (/opt/nordic/ncs/v3.1.1/modules/lib/nrf_wifi)
#
CONFIG_ZEPHYR_NRF_WIFI_MODULE=y
# CONFIG_NRF70_BUSLIB is not set
# end of nrf_wifi (/opt/nordic/ncs/v3.1.1/modules/lib/nrf_wifi)

CONFIG_ZEPHYR_OPEN_AMP_MODULE=y

#
# percepio (/opt/nordic/ncs/v3.1.1/modules/debug/percepio)
#

#
# Percepio Tracealyzer support can be enabled from the tracing subsystem
#
# CONFIG_PERCEPIO_DFM is not set
CONFIG_ZEPHYR_PERCEPIO_MODULE=y
# end of percepio (/opt/nordic/ncs/v3.1.1/modules/debug/percepio)

#
# picolibc (/opt/nordic/ncs/v3.1.1/modules/lib/picolibc)
#
# CONFIG_PICOLIBC_MODULE is not set
CONFIG_ZEPHYR_PICOLIBC_MODULE=y
# end of picolibc (/opt/nordic/ncs/v3.1.1/modules/lib/picolibc)

#
# segger (/opt/nordic/ncs/v3.1.1/modules/debug/segger)
#
CONFIG_ZEPHYR_SEGGER_MODULE=y
CONFIG_HAS_SEGGER_RTT=y
CONFIG_USE_SEGGER_RTT=y
CONFIG_SEGGER_RTT_CUSTOM_LOCKING=y
CONFIG_SEGGER_RTT_CB_ALIGNMENT=16
CONFIG_SEGGER_RTT_MAX_NUM_UP_BUFFERS=3
CONFIG_SEGGER_RTT_MAX_NUM_DOWN_BUFFERS=3
CONFIG_SEGGER_RTT_BUFFER_SIZE_UP=4096
CONFIG_SEGGER_RTT_BUFFER_SIZE_DOWN=16
CONFIG_SEGGER_RTT_PRINTF_BUFFER_SIZE=64
CONFIG_SEGGER_RTT_MODE_NO_BLOCK_SKIP=y
# CONFIG_SEGGER_RTT_MODE_NO_BLOCK_TRIM is not set
# CONFIG_SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL is not set
CONFIG_SEGGER_RTT_MODE=0
# CONFIG_SEGGER_RTT_MEMCPY_USE_BYTELOOP is not set
# CONFIG_SEGGER_RTT_SECTION_NONE is not set
# CONFIG_SEGGER_RTT_SECTION_DTCM is not set
# CONFIG_SEGGER_RTT_SECTION_CCM is not set
CONFIG_SEGGER_RTT_SECTION_CUSTOM=y
# CONFIG_SEGGER_RTT_SECTION_CUSTOM_DTS_REGION is not set
CONFIG_SEGGER_RTT_SECTION_CUSTOM_NAME=".rtt_buff_data"
# CONFIG_SEGGER_RTT_INIT_MODE_ALWAYS is not set
CONFIG_SEGGER_RTT_INIT_MODE_STRONG_CHECK=y
# CONFIG_SEGGER_RTT_INIT_MODE_WEAK_CHECK is not set
# end of segger (/opt/nordic/ncs/v3.1.1/modules/debug/segger)

#
# uoscore-uedhoc (/opt/nordic/ncs/v3.1.1/modules/lib/uoscore-uedhoc)
#
CONFIG_ZEPHYR_UOSCORE_UEDHOC_MODULE=y
# end of uoscore-uedhoc (/opt/nordic/ncs/v3.1.1/modules/lib/uoscore-uedhoc)

#
# zcbor (/opt/nordic/ncs/v3.1.1/modules/lib/zcbor)
#
CONFIG_ZEPHYR_ZCBOR_MODULE=y
# CONFIG_ZCBOR is not set
# end of zcbor (/opt/nordic/ncs/v3.1.1/modules/lib/zcbor)

#
# nrfxlib (/opt/nordic/ncs/v3.1.1/nrfxlib)
#

#
# Nordic nrfxlib
#

#
# nrf_modem (Modem library)
#
CONFIG_NRF_MODEM_SHMEM_CTRL_SIZE=0x4e8
# end of nrf_modem (Modem library)

# CONFIG_NFC_T2T_NRFXLIB is not set
# CONFIG_NFC_T4T_NRFXLIB is not set
CONFIG_MPSL=y
CONFIG_MPSL_BUILD_TYPE_LIB=y
CONFIG_MPSL_LIB_DIR="nrf52"
CONFIG_MPSL_LIB_FLOAT_ABI_DIR="soft-float"

#
# Crypto libraries for nRF5x SOCs.
#
CONFIG_NRFXLIB_CRYPTO=y
CONFIG_HAS_HW_NRF_CC3XX=y
# CONFIG_NRF_OBERON is not set
# CONFIG_NRF_CC310_BL is not set
CONFIG_NRF_CC3XX_PLATFORM=y
CONFIG_CC3XX_MUTEX_LOCK=y
# CONFIG_CC3XX_ATOMIC_LOCK is not set
# end of Crypto libraries for nRF5x SOCs.

# CONFIG_NRF_RPC is not set
CONFIG_NRF_802154_SOURCE_NRFXLIB=y
# CONFIG_GZLL is not set
# CONFIG_NRF_DM is not set
# CONFIG_NRF_FUEL_GAUGE is not set
# end of Nordic nrfxlib

CONFIG_ZEPHYR_NRFXLIB_MODULE=y
# end of nrfxlib (/opt/nordic/ncs/v3.1.1/nrfxlib)

CONFIG_ZEPHYR_NRF_HW_MODELS_MODULE=y

#
# connectedhomeip (/opt/nordic/ncs/v3.1.1/modules/lib/matter)
#
# CONFIG_CHIP is not set
# CONFIG_CHIP_CUSTOM_BLE_ADV_DATA is not set
CONFIG_ZEPHYR_CONNECTEDHOMEIP_MODULE=y
# end of connectedhomeip (/opt/nordic/ncs/v3.1.1/modules/lib/matter)

# CONFIG_LIBMETAL is not set
# CONFIG_LVGL is not set
# CONFIG_HAS_MEC_HAL is not set
# CONFIG_HAS_MPFS_HAL is not set
# CONFIG_HAS_MEC5_HAL is not set
# CONFIG_OPENAMP is not set
# CONFIG_MIPI_SYST_LIB is not set
# CONFIG_HAS_TELINK_DRIVERS is not set
# CONFIG_MCUBOOT_BOOTUTIL_LIB is not set

#
# Unavailable modules, please install those via the project manifest.
#

#
# hal_bouffalolab module not available.
#

#
# hal_gigadevice module not available.
#

#
# hal_nxp module not available.
#

#
# libsbc module not available.
#

#
# Trusted-firmware-a module not available.
#

#
# LoRa Basics Modem module not available.
#

#
# THRIFT module not available.
#
# CONFIG_ACPI is not set
# end of Modules

CONFIG_BOARD="nrf52840dk"
CONFIG_BOARD_REVISION=""
CONFIG_BOARD_TARGET="nrf52840dk/nrf52840"
# CONFIG_NET_DRIVERS is not set
CONFIG_BOARD_NRF52840DK=y
CONFIG_BOARD_NRF52840DK_NRF52840=y
CONFIG_BOARD_QUALIFIERS="nrf52840"

#
# Board Options
#
# end of Board Options

#
# Hardware Configuration
#
CONFIG_SOC="nrf52840"
CONFIG_SOC_SERIES="nrf52"
CONFIG_SOC_FAMILY="nordic_nrf"
CONFIG_SOC_FAMILY_NORDIC_NRF=y
CONFIG_SOC_SERIES_NRF52X=y
CONFIG_SOC_NRF52840=y
CONFIG_SOC_NRF52840_QIAA=y
# CONFIG_HWINFO is not set
# CONFIG_BUILD_OUTPUT_INFO_HEADER is not set
CONFIG_SOC_COMPATIBLE_NRF=y
CONFIG_SOC_COMPATIBLE_NRF52X=y
CONFIG_SOC_NORDIC_BSP_NAME="stable"
CONFIG_HAS_HW_NRF_ACL=y
CONFIG_HAS_HW_NRF_CC310=y
CONFIG_HAS_HW_NRF_CCM=y
CONFIG_HAS_HW_NRF_CCM_LFLEN_8BIT=y
CONFIG_HAS_HW_NRF_CLOCK=y
CONFIG_HAS_HW_NRF_ECB=y
CONFIG_HAS_HW_NRF_EGU0=y
CONFIG_HAS_HW_NRF_EGU1=y
CONFIG_HAS_HW_NRF_EGU2=y
CONFIG_HAS_HW_NRF_EGU3=y
CONFIG_HAS_HW_NRF_EGU4=y
CONFIG_HAS_HW_NRF_EGU5=y
CONFIG_HAS_HW_NRF_GPIO0=y
CONFIG_HAS_HW_NRF_GPIO1=y
CONFIG_HAS_HW_NRF_GPIOTE0=y
CONFIG_HAS_HW_NRF_MWU=y
CONFIG_HAS_HW_NRF_NFCT=y
CONFIG_HAS_HW_NRF_NVMC_PE=y
CONFIG_HAS_HW_NRF_POWER=y
CONFIG_HAS_HW_NRF_PPI=y
CONFIG_HAS_HW_NRF_QSPI=y
CONFIG_HAS_HW_NRF_RADIO_BLE_2M=y
CONFIG_HAS_HW_NRF_RADIO_BLE_CODED=y
CONFIG_HAS_HW_NRF_RADIO_IEEE802154=y
CONFIG_HAS_HW_NRF_RADIO_TX_PWR_HIGH=y
CONFIG_HAS_HW_NRF_RNG=y
CONFIG_HAS_HW_NRF_SAADC=y
CONFIG_HAS_HW_NRF_SPI1=y
CONFIG_HAS_HW_NRF_SWI0=y
CONFIG_HAS_HW_NRF_SWI1=y
CONFIG_HAS_HW_NRF_SWI2=y
CONFIG_HAS_HW_NRF_SWI3=y
CONFIG_HAS_HW_NRF_SWI4=y
CONFIG_HAS_HW_NRF_SWI5=y
CONFIG_HAS_HW_NRF_TEMP=y
CONFIG_HAS_HW_NRF_TWI0=y
CONFIG_HAS_HW_NRF_UARTE0=y
CONFIG_HAS_HW_NRF_UARTE1=y
CONFIG_HAS_HW_NRF_USBD=y
CONFIG_HAS_NORDIC_RAM_CTRL=y
# CONFIG_NRF_FORCE_RAM_ON_REBOOT is not set
# CONFIG_NRF_SYS_EVENT is not set
# CONFIG_NRF_PERIPHCONF_SECTION is not set
# CONFIG_IS_IRONSIDE_SE_SECONDARY_IMAGE is not set
# CONFIG_IS_GEN_UICR_IMAGE is not set
CONFIG_NRF_ENABLE_ICACHE=y
CONFIG_NRF_RTC_TIMER_USER_CHAN_COUNT=0
# CONFIG_SOC_NRF54H20_PM_S2RAM_OVERRIDE is not set
CONFIG_NRF_SOC_SECURE_SUPPORTED=y
CONFIG_NRF_APPROTECT_USE_UICR=y
# CONFIG_NRF_APPROTECT_LOCK is not set
# CONFIG_NRF_TRACE_PORT is not set
CONFIG_GPIO_INIT_PRIORITY=40
# CONFIG_SOC_LOG_LEVEL_OFF is not set
# CONFIG_SOC_LOG_LEVEL_ERR is not set
# CONFIG_SOC_LOG_LEVEL_WRN is not set
# CONFIG_SOC_LOG_LEVEL_INF is not set
# CONFIG_SOC_LOG_LEVEL_DBG is not set
CONFIG_SOC_LOG_LEVEL_DEFAULT=y
CONFIG_SOC_LOG_LEVEL=3
# end of Hardware Configuration

CONFIG_ARCH="arm"
# CONFIG_EXTRA_EXCEPTION_INFO is not set
CONFIG_ARCH_HAS_SINGLE_THREAD_SUPPORT=y
CONFIG_CPU_CORTEX=y
CONFIG_ARM_MPU_REGION_MIN_ALIGN_AND_SIZE=32
# CONFIG_MPU_ALLOW_FLASH_WRITE is not set

#
# ARM Options
#
CONFIG_CPU_CORTEX_M=y
# CONFIG_ARM_ZIMAGE_HEADER is not set
CONFIG_ISA_THUMB2=y
CONFIG_ASSEMBLER_ISA_THUMB2=y
CONFIG_COMPILER_ISA_THUMB2=y
CONFIG_STACK_ALIGN_DOUBLE_WORD=y
# CONFIG_RUNTIME_NMI is not set
# CONFIG_PLATFORM_SPECIFIC_INIT is not set
CONFIG_FAULT_DUMP=2
CONFIG_ARM_STACK_PROTECTION=y
CONFIG_FP16=y
CONFIG_FP16_IEEE=y
# CONFIG_FP16_ALT is not set
CONFIG_CPU_CORTEX_M4=y
CONFIG_CPU_CORTEX_M_HAS_SYSTICK=y
CONFIG_CPU_CORTEX_M_HAS_DWT=y
CONFIG_CPU_CORTEX_M_HAS_BASEPRI=y
CONFIG_CPU_CORTEX_M_HAS_VTOR=y
CONFIG_CPU_CORTEX_M_HAS_PROGRAMMABLE_FAULT_PRIOS=y
CONFIG_ARMV7_M_ARMV8_M_MAINLINE=y
CONFIG_ARMV7_M_ARMV8_M_FP=y

#
# ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33/M55 options
#
# CONFIG_SW_VECTOR_RELAY is not set
# CONFIG_CORTEX_M_DWT is not set
# CONFIG_CORTEX_M_DEBUG_MONITOR_HOOK is not set
# CONFIG_TRAP_UNALIGNED_ACCESS is not set
# end of ARM Cortex-M0/M0+/M1/M3/M4/M7/M23/M33/M55 options

CONFIG_NULL_POINTER_EXCEPTION_DETECTION_NONE=y
# CONFIG_NULL_POINTER_EXCEPTION_DETECTION_DWT is not set
# CONFIG_NULL_POINTER_EXCEPTION_DETECTION_MPU is not set
CONFIG_MPU_STACK_GUARD=y
# CONFIG_MPU_DISABLE_BACKGROUND_MAP is not set
# CONFIG_CUSTOM_SECTION_ALIGN is not set
CONFIG_CUSTOM_SECTION_MIN_ALIGN_SIZE=32
CONFIG_HAS_SWO=y
# end of ARM Options

CONFIG_ARM=y
CONFIG_ARCH_IS_SET=y

#
# General Architecture Options
#
# CONFIG_SEMIHOST is not set
CONFIG_ARCH_SUPPORTS_ROM_OFFSET=y
CONFIG_ARM_MPU=y
# CONFIG_ARCH_LOG_LEVEL_OFF is not set
# CONFIG_ARCH_LOG_LEVEL_ERR is not set
# CONFIG_ARCH_LOG_LEVEL_WRN is not set
# CONFIG_ARCH_LOG_LEVEL_INF is not set
# CONFIG_ARCH_LOG_LEVEL_DBG is not set
CONFIG_ARCH_LOG_LEVEL_DEFAULT=y
CONFIG_ARCH_LOG_LEVEL=3
CONFIG_LITTLE_ENDIAN=y
# CONFIG_USERSPACE is not set
# CONFIG_NOINIT_SNIPPET_FIRST is not set
CONFIG_GEN_PRIV_STACKS=y
# CONFIG_STACK_GROWS_UP is not set
# CONFIG_FRAME_POINTER is not set

#
# Interrupt Configuration
#
# CONFIG_ISR_TABLES_LOCAL_DECLARATION is not set
CONFIG_ARCH_DEVICE_STATE_ALIGN=4
CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_ADDRESS=y
# CONFIG_IRQ_VECTOR_TABLE_JUMP_BY_CODE is not set
# CONFIG_SRAM_SW_ISR_TABLE is not set
CONFIG_EXCEPTION_DEBUG=y
# CONFIG_SIMPLIFIED_EXCEPTION_CODES is not set
# end of Interrupt Configuration
# end of General Architecture Options

CONFIG_ARCH_HAS_TIMING_FUNCTIONS=y
CONFIG_ARCH_HAS_STACK_PROTECTION=y
CONFIG_ARCH_HAS_USERSPACE=y
CONFIG_ARCH_HAS_EXECUTABLE_PAGE_BIT=y
CONFIG_ARCH_HAS_RAMFUNC_SUPPORT=y
CONFIG_ARCH_HAS_VECTOR_TABLE_RELOCATION=y
CONFIG_ARCH_HAS_NESTED_EXCEPTION_DETECTION=y
CONFIG_ARCH_SUPPORTS_COREDUMP=y
CONFIG_ARCH_SUPPORTS_COREDUMP_THREADS=y
CONFIG_ARCH_SUPPORTS_COREDUMP_STACK_PTR=y
CONFIG_ARCH_SUPPORTS_ARCH_HW_INIT=y
CONFIG_ARCH_SUPPORTS_ROM_START=y
CONFIG_ARCH_HAS_EXTRA_EXCEPTION_INFO=y
CONFIG_ARCH_HAS_THREAD_LOCAL_STORAGE=y
CONFIG_ARCH_HAS_SUSPEND_TO_RAM=y
CONFIG_ARCH_HAS_THREAD_ABORT=y
CONFIG_ARCH_HAS_CODE_DATA_RELOCATION=y
CONFIG_CPU_HAS_FPU=y
CONFIG_CPU_HAS_MPU=y
CONFIG_MPU=y
# CONFIG_MPU_LOG_LEVEL_OFF is not set
# CONFIG_MPU_LOG_LEVEL_ERR is not set
# CONFIG_MPU_LOG_LEVEL_WRN is not set
# CONFIG_MPU_LOG_LEVEL_INF is not set
# CONFIG_MPU_LOG_LEVEL_DBG is not set
CONFIG_MPU_LOG_LEVEL_DEFAULT=y
CONFIG_MPU_LOG_LEVEL=3
CONFIG_MPU_REQUIRES_POWER_OF_TWO_ALIGNMENT=y
CONFIG_SRAM_REGION_PERMISSIONS=y

#
# DSP Options
#
# end of DSP Options

#
# Floating Point Options
#
# end of Floating Point Options

#
# Cache Options
#
# end of Cache Options

CONFIG_TOOLCHAIN_HAS_BUILTIN_FFS=y
CONFIG_ARCH_HAS_CUSTOM_SWAP_TO_MAIN=y

#
# General Kernel Options
#
# CONFIG_KERNEL_LOG_LEVEL_OFF is not set
# CONFIG_KERNEL_LOG_LEVEL_ERR is not set
# CONFIG_KERNEL_LOG_LEVEL_WRN is not set
# CONFIG_KERNEL_LOG_LEVEL_INF is not set
# CONFIG_KERNEL_LOG_LEVEL_DBG is not set
CONFIG_KERNEL_LOG_LEVEL_DEFAULT=y
CONFIG_KERNEL_LOG_LEVEL=3
CONFIG_NUM_COOP_PRIORITIES=16
CONFIG_MAIN_THREAD_PRIORITY=0
CONFIG_COOP_ENABLED=y
CONFIG_PREEMPT_ENABLED=y
CONFIG_PRIORITY_CEILING=-127
# CONFIG_SCHED_DEADLINE is not set
CONFIG_THREAD_STACK_INFO=y
# CONFIG_THREAD_CUSTOM_DATA is not set
# CONFIG_DYNAMIC_THREAD is not set
# CONFIG_SCHED_DUMB is not set
CONFIG_SCHED_SIMPLE=y
# CONFIG_SCHED_SCALABLE is not set
# CONFIG_SCHED_MULTIQ is not set
# CONFIG_WAITQ_DUMB is not set
# CONFIG_WAITQ_SCALABLE is not set
CONFIG_WAITQ_SIMPLE=y

#
# Misc Kernel related options
#
CONFIG_LIBC_ERRNO=y
CONFIG_ERRNO=y
CONFIG_CURRENT_THREAD_USE_TLS=y
# end of Misc Kernel related options

#
# Kernel Debugging and Metrics
#
CONFIG_BOOT_DELAY=0
# CONFIG_BOOT_CLEAR_SCREEN is not set
CONFIG_THREAD_MONITOR=y
CONFIG_THREAD_NAME=y
CONFIG_THREAD_MAX_NAME_LEN=32
CONFIG_INSTRUMENT_THREAD_SWITCHING=y
CONFIG_THREAD_RUNTIME_STATS=y
# CONFIG_THREAD_RUNTIME_STATS_USE_TIMING_FUNCTIONS is not set
CONFIG_SCHED_THREAD_USAGE=y
# CONFIG_SCHED_THREAD_USAGE_ANALYSIS is not set
CONFIG_SCHED_THREAD_USAGE_ALL=y
CONFIG_SCHED_THREAD_USAGE_AUTO_ENABLE=y
# end of Kernel Debugging and Metrics

# CONFIG_OBJ_CORE is not set
# CONFIG_WORKQUEUE_WORK_TIMEOUT is not set

#
# System Work Queue Options
#
# CONFIG_SYSTEM_WORKQUEUE_NO_YIELD is not set
CONFIG_SYSTEM_WORKQUEUE_WORK_TIMEOUT_MS=5000
# end of System Work Queue Options

#
# Barrier Operations
#
CONFIG_BARRIER_OPERATIONS_ARCH=y
# end of Barrier Operations

#
# Atomic Operations
#
CONFIG_ATOMIC_OPERATIONS_BUILTIN=y
# end of Atomic Operations

#
# Timer API Options
#
CONFIG_TIMESLICING=y
CONFIG_TIMESLICE_PRIORITY=0
# CONFIG_TIMESLICE_PER_THREAD is not set
# end of Timer API Options

#
# Other Kernel Object Options
#
CONFIG_POLL=y
CONFIG_MEM_SLAB_POINTER_VALIDATE=y
# CONFIG_MEM_SLAB_TRACE_MAX_UTILIZATION is not set
CONFIG_NUM_MBOX_ASYNC_MSGS=10
# CONFIG_EVENTS is not set
# CONFIG_HEAP_MEM_POOL_IGNORE_MIN is not set
# end of Other Kernel Object Options

CONFIG_SWAP_NONATOMIC=y
CONFIG_TIMEOUT_64BIT=y
CONFIG_SYS_CLOCK_MAX_TIMEOUT_DAYS=365

#
# Security Options
#
CONFIG_STACK_POINTER_RANDOM=0
# end of Security Options

#
# Memory Domains
#
CONFIG_ARCH_MEM_DOMAIN_SUPPORTS_ISOLATED_STACKS=y
CONFIG_MEM_DOMAIN_ISOLATED_STACKS=y
# end of Memory Domains

#
# SMP Options
#
# CONFIG_TICKET_SPINLOCKS is not set
# end of SMP Options

CONFIG_TOOLCHAIN_SUPPORTS_THREAD_LOCAL_STORAGE=y
CONFIG_THREAD_LOCAL_STORAGE=y
CONFIG_TOOLCHAIN_SUPPORTS_STATIC_INIT_GNU=y
# CONFIG_STATIC_INIT_GNU is not set
# CONFIG_BOOTARGS is not set
# end of General Kernel Options

#
# Device Options
#
# CONFIG_DEVICE_MUTABLE is not set
# CONFIG_DEVICE_DT_METADATA is not set
CONFIG_DEVICE_DEINIT_SUPPORT=y
# end of Device Options

#
# Initialization Priorities
#
CONFIG_KERNEL_INIT_PRIORITY_OBJECTS=30
CONFIG_KERNEL_INIT_PRIORITY_LIBC=35
CONFIG_KERNEL_INIT_PRIORITY_DEFAULT=40
CONFIG_KERNEL_INIT_PRIORITY_DEVICE=50
CONFIG_APPLICATION_INIT_PRIORITY=90
# end of Initialization Priorities

#
# Virtual Memory Support
#

#
# MMU Features
#
# end of MMU Features
# end of Virtual Memory Support

#
# SoC and Board Hooks
#
# CONFIG_SOC_EARLY_RESET_HOOK is not set
# CONFIG_SOC_PREP_HOOK is not set
# CONFIG_SOC_EARLY_INIT_HOOK is not set
# CONFIG_SOC_LATE_INIT_HOOK is not set
# CONFIG_SOC_PER_CORE_INIT_HOOK is not set
# CONFIG_BOARD_EARLY_INIT_HOOK is not set
# CONFIG_BOARD_LATE_INIT_HOOK is not set
# end of SoC and Board Hooks

#
# Device Drivers
#
# CONFIG_ADC is not set
# CONFIG_AUDIO is not set
# CONFIG_AUXDISPLAY is not set
# CONFIG_BBRAM is not set
CONFIG_BT_DRIVERS=y

#
# Bluetooth HCI Driver Options
#
CONFIG_BT_HCI_INIT_PRIORITY=50
# CONFIG_HCI_NXP_SET_CAL_DATA_ANNEX100 is not set
CONFIG_BT_DRV_TX_STACK_SIZE=256
CONFIG_BT_DRV_RX_STACK_SIZE=768
# CONFIG_CAN is not set
# CONFIG_CHARGER is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_OFF is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_ERR is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_WRN is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_INF is not set
# CONFIG_CLOCK_CONTROL_LOG_LEVEL_DBG is not set
CONFIG_CLOCK_CONTROL_LOG_LEVEL_DEFAULT=y
CONFIG_CLOCK_CONTROL_LOG_LEVEL=3
CONFIG_CLOCK_CONTROL_NRF_FORCE_ALT=y
CONFIG_CLOCK_CONTROL_NRF=y
CONFIG_CLOCK_CONTROL_NRF_K32SRC_FREQUENCY=32768
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_SYNTH is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_EXT_LOW_SWING is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_EXT_FULL_SWING is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_500PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_250PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_150PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_100PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_75PPM is not set
CONFIG_CLOCK_CONTROL_NRF_K32SRC_50PPM=y
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_30PPM is not set
# CONFIG_CLOCK_CONTROL_NRF_K32SRC_20PPM is not set
CONFIG_CLOCK_CONTROL_NRF_ACCURACY=50
# CONFIG_CLOCK_CONTROL_FIXED_RATE_CLOCK is not set
# CONFIG_COMPARATOR is not set
CONFIG_CONSOLE_INPUT_MAX_LINE_LEN=128
CONFIG_CONSOLE_HAS_DRIVER=y
# CONFIG_CONSOLE_HANDLER is not set
CONFIG_CONSOLE_INIT_PRIORITY=60
CONFIG_UART_CONSOLE=y
# CONFIG_UART_CONSOLE_DEBUG_SERVER_HOOKS is not set
# CONFIG_UART_CONSOLE_MCUMGR is not set
# CONFIG_RAM_CONSOLE is not set
CONFIG_RTT_CONSOLE=y
CONFIG_RTT_TX_RETRY_CNT=2
CONFIG_RTT_TX_RETRY_DELAY_MS=2
# CONFIG_RTT_TX_RETRY_IN_INTERRUPT is not set
# CONFIG_IPM_CONSOLE_SENDER is not set
# CONFIG_IPM_CONSOLE_RECEIVER is not set
# CONFIG_UART_MCUMGR is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_OFF is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_ERR is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_WRN is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_INF is not set
# CONFIG_UART_CONSOLE_LOG_LEVEL_DBG is not set
CONFIG_UART_CONSOLE_LOG_LEVEL_DEFAULT=y
CONFIG_UART_CONSOLE_LOG_LEVEL=3
# CONFIG_EFI_CONSOLE is not set
# CONFIG_COREDUMP_DEVICE is not set
# CONFIG_CRC_DRIVER is not set
# CONFIG_CRYPTO is not set
# CONFIG_DAC is not set
# CONFIG_DAI is not set
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DISK_DRIVERS is not set
# CONFIG_DISPLAY is not set
# CONFIG_DMA is not set
# CONFIG_DP_DRIVER is not set
# CONFIG_EDAC is not set
# CONFIG_EEPROM is not set
CONFIG_ENTROPY_GENERATOR=y
# CONFIG_ENTROPY_LOG_LEVEL_OFF is not set
# CONFIG_ENTROPY_LOG_LEVEL_ERR is not set
# CONFIG_ENTROPY_LOG_LEVEL_WRN is not set
# CONFIG_ENTROPY_LOG_LEVEL_INF is not set
# CONFIG_ENTROPY_LOG_LEVEL_DBG is not set
CONFIG_ENTROPY_LOG_LEVEL_DEFAULT=y
CONFIG_ENTROPY_LOG_LEVEL=3
CONFIG_ENTROPY_INIT_PRIORITY=50
# CONFIG_FAKE_ENTROPY_NATIVE_POSIX is not set
CONFIG_ENTROPY_NRF5_RNG=y
# CONFIG_ENTROPY_NRF5_BIAS_CORRECTION is not set
CONFIG_ENTROPY_NRF5_THR_POOL_SIZE=8
CONFIG_ENTROPY_NRF5_THR_THRESHOLD=4
CONFIG_ENTROPY_NRF5_ISR_POOL_SIZE=16
CONFIG_ENTROPY_NRF5_ISR_THRESHOLD=12
CONFIG_ENTROPY_HAS_DRIVER=y
# CONFIG_ESPI is not set

#
# Firmware drivers
#
# CONFIG_ARM_SCMI is not set
# end of Firmware drivers

# CONFIG_FPGA is not set
# CONFIG_FUEL_GAUGE is not set
# CONFIG_GNSS is not set
# CONFIG_GPIO_LOG_LEVEL_OFF is not set
# CONFIG_GPIO_LOG_LEVEL_ERR is not set
# CONFIG_GPIO_LOG_LEVEL_WRN is not set
# CONFIG_GPIO_LOG_LEVEL_INF is not set
# CONFIG_GPIO_LOG_LEVEL_DBG is not set
CONFIG_GPIO_LOG_LEVEL_DEFAULT=y
CONFIG_GPIO_LOG_LEVEL=3
# CONFIG_GPIO_GET_DIRECTION is not set
# CONFIG_GPIO_GET_CONFIG is not set
# CONFIG_GPIO_HOGS is not set
# CONFIG_GPIO_ENABLE_DISABLE_INTERRUPT is not set
CONFIG_GPIO_NRFX=y
CONFIG_GPIO_NRFX_INTERRUPT=y
# CONFIG_HAPTICS is not set
# CONFIG_HWSPINLOCK is not set
# CONFIG_I2C is not set
# CONFIG_I2S is not set
# CONFIG_I3C is not set

#
# Interrupt controller drivers
#
CONFIG_INTC_INIT_PRIORITY=40
# CONFIG_INTC_LOG_LEVEL_OFF is not set
# CONFIG_INTC_LOG_LEVEL_ERR is not set
# CONFIG_INTC_LOG_LEVEL_WRN is not set
# CONFIG_INTC_LOG_LEVEL_INF is not set
# CONFIG_INTC_LOG_LEVEL_DBG is not set
CONFIG_INTC_LOG_LEVEL_DEFAULT=y
CONFIG_INTC_LOG_LEVEL=3
# end of Interrupt controller drivers

# CONFIG_IPM is not set
# CONFIG_LED is not set
# CONFIG_LED_STRIP is not set
# CONFIG_LORA is not set
# CONFIG_MBOX is not set
# CONFIG_MDIO is not set
# CONFIG_MIPI_DBI is not set

#
# Miscellaneous Drivers
#
# CONFIG_TIMEAWARE_GPIO is not set

#
# Interconn Drivers
#
# end of Interconn Drivers
# end of Miscellaneous Drivers

# CONFIG_MM_DRV is not set
# CONFIG_MSPI is not set
# CONFIG_PCIE is not set
# CONFIG_PCIE_ENDPOINT is not set
# CONFIG_PECI is not set
CONFIG_PINCTRL=y
# CONFIG_PINCTRL_LOG_LEVEL_OFF is not set
# CONFIG_PINCTRL_LOG_LEVEL_ERR is not set
# CONFIG_PINCTRL_LOG_LEVEL_WRN is not set
# CONFIG_PINCTRL_LOG_LEVEL_INF is not set
# CONFIG_PINCTRL_LOG_LEVEL_DBG is not set
CONFIG_PINCTRL_LOG_LEVEL_DEFAULT=y
CONFIG_PINCTRL_LOG_LEVEL=3
CONFIG_PINCTRL_STORE_REG=y
# CONFIG_PINCTRL_DYNAMIC is not set
CONFIG_PINCTRL_KEEP_SLEEP_STATE=y
# CONFIG_PINCTRL_NPCX_EX is not set
CONFIG_PINCTRL_NRF=y
# CONFIG_PM_CPU_OPS is not set
# CONFIG_PS2 is not set
# CONFIG_PSI5 is not set
# CONFIG_PTP_CLOCK is not set
# CONFIG_PWM is not set
# CONFIG_RETAINED_MEM is not set
# CONFIG_RTC is not set
# CONFIG_SDHC is not set
# CONFIG_SENT is not set

#
# Capabilities
#
CONFIG_SERIAL_HAS_DRIVER=y
CONFIG_SERIAL_SUPPORT_ASYNC=y
CONFIG_SERIAL_SUPPORT_INTERRUPT=y
CONFIG_SERIAL_INIT_PRIORITY=50
# CONFIG_UART_LOG_LEVEL_OFF is not set
# CONFIG_UART_LOG_LEVEL_ERR is not set
# CONFIG_UART_LOG_LEVEL_WRN is not set
# CONFIG_UART_LOG_LEVEL_INF is not set
# CONFIG_UART_LOG_LEVEL_DBG is not set
CONFIG_UART_LOG_LEVEL_DEFAULT=y
CONFIG_UART_LOG_LEVEL=3
CONFIG_UART_ASYNC_API=y
CONFIG_UART_EXCLUSIVE_API_CALLBACKS=y
# CONFIG_UART_LINE_CTRL is not set
# CONFIG_UART_DRV_CMD is not set
# CONFIG_UART_WIDE_DATA is not set
# CONFIG_UART_PIPE is not set
# CONFIG_UART_ASYNC_RX_HELPER is not set

#
# Serial Drivers
#
# CONFIG_UART_NATIVE_POSIX is not set
# CONFIG_UART_NPCX_FIFO_EX is not set
CONFIG_UART_NRFX=y
CONFIG_UART_NRFX_UARTE=y
CONFIG_UART_NRFX_UARTE_LEGACY_SHIM=y
CONFIG_UART_ASYNC_TX_CACHE_SIZE=8
# CONFIG_UARTE_NRFX_UARTE_COUNT_BYTES_WITH_TIMER is not set
# CONFIG_UART_NRFX_UARTE_DIRECT_ISR is not set
CONFIG_UART_0_INTERRUPT_DRIVEN=y
CONFIG_UART_0_ENHANCED_POLL_OUT=y
# CONFIG_UART_0_NRF_PARITY_BIT is not set
CONFIG_UART_0_NRF_TX_BUFFER_SIZE=32
# CONFIG_UART_0_NRF_HW_ASYNC is not set
CONFIG_UART_0_NRF_ASYNC_LOW_POWER=y
# CONFIG_UART_1_INTERRUPT_DRIVEN is not set
CONFIG_UART_1_ASYNC=y
CONFIG_UART_1_ENHANCED_POLL_OUT=y
# CONFIG_UART_1_NRF_PARITY_BIT is not set
CONFIG_UART_1_NRF_TX_BUFFER_SIZE=32
CONFIG_UART_1_NRF_HW_ASYNC=y
CONFIG_UART_1_NRF_ASYNC_LOW_POWER=y
CONFIG_UART_1_NRF_HW_ASYNC_TIMER=2
# CONFIG_SMBUS is not set
# CONFIG_STEPPER is not set

#
# Timer drivers
#
# CONFIG_TIMER_READS_ITS_FREQUENCY_AT_RUNTIME is not set
# CONFIG_SYSTEM_CLOCK_SLOPPY_IDLE is not set
CONFIG_SYSTEM_CLOCK_INIT_PRIORITY=0
CONFIG_TICKLESS_CAPABLE=y
CONFIG_SYSTEM_TIMER_HAS_DISABLE_SUPPORT=y
CONFIG_NRF_RTC_TIMER=y
CONFIG_NRF_RTC_TIMER_LOCK_ZERO_LATENCY_IRQS=y
# CONFIG_NRF_RTC_TIMER_TRIGGER_OVERFLOW is not set
CONFIG_NRF_RTC_COUNTER_BIT_WIDTH=24
# CONFIG_SYSTEM_CLOCK_NO_WAIT is not set
# CONFIG_SYSTEM_CLOCK_WAIT_FOR_AVAILABILITY is not set
CONFIG_SYSTEM_CLOCK_WAIT_FOR_STABILITY=y
# end of Timer drivers

# CONFIG_USB_BC12 is not set
# CONFIG_UDC_DRIVER is not set
# CONFIG_UHC_DRIVER is not set
# CONFIG_UVB is not set
# CONFIG_USB_DEVICE_DRIVER is not set

#
# USB common
#
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_OFF is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_ERR is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_WRN is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_INF is not set
# CONFIG_NRF_USBD_COMMON_LOG_LEVEL_DBG is not set
CONFIG_NRF_USBD_COMMON_LOG_LEVEL_DEFAULT=y
CONFIG_NRF_USBD_COMMON_LOG_LEVEL=3
# CONFIG_NRF_USBD_COMMON is not set
# end of USB common

# CONFIG_USBC_TCPC_DRIVER is not set
# CONFIG_USBC_LOG_LEVEL_OFF is not set
# CONFIG_USBC_LOG_LEVEL_ERR is not set
# CONFIG_USBC_LOG_LEVEL_WRN is not set
# CONFIG_USBC_LOG_LEVEL_INF is not set
# CONFIG_USBC_LOG_LEVEL_DBG is not set
CONFIG_USBC_LOG_LEVEL_DEFAULT=y
CONFIG_USBC_LOG_LEVEL=3
# CONFIG_USBC_VBUS_DRIVER is not set
# CONFIG_USBC_PPC_DRIVER is not set
# CONFIG_VIDEO is not set
# CONFIG_VIRTIO is not set
# CONFIG_VIRTIO_LOG_LEVEL_OFF is not set
# CONFIG_VIRTIO_LOG_LEVEL_ERR is not set
# CONFIG_VIRTIO_LOG_LEVEL_WRN is not set
# CONFIG_VIRTIO_LOG_LEVEL_INF is not set
# CONFIG_VIRTIO_LOG_LEVEL_DBG is not set
CONFIG_VIRTIO_LOG_LEVEL_DEFAULT=y
CONFIG_VIRTIO_LOG_LEVEL=3
# CONFIG_VIRTUALIZATION is not set
# CONFIG_W1 is not set
# CONFIG_TEE is not set
# end of Device Drivers

# CONFIG_REQUIRES_FULL_LIBC is not set
# CONFIG_REQUIRES_FLOAT_PRINTF is not set
# CONFIG_LIBC_ALLOW_LESS_THAN_64BIT_TIME is not set
CONFIG_FULL_LIBC_SUPPORTED=y
CONFIG_MINIMAL_LIBC_SUPPORTED=y
CONFIG_NEWLIB_LIBC_SUPPORTED=y
CONFIG_PICOLIBC_SUPPORTED=y

#
# C Library
#
# CONFIG_MINIMAL_LIBC is not set
CONFIG_PICOLIBC=y
# CONFIG_NEWLIB_LIBC is not set
# CONFIG_EXTERNAL_LIBC is not set
CONFIG_HAS_NEWLIB_LIBC_NANO=y
CONFIG_COMMON_LIBC_ABORT=y
# CONFIG_COMMON_LIBC_ASCTIME_R is not set
# CONFIG_COMMON_LIBC_CTIME_R is not set
CONFIG_COMMON_LIBC_TIME=y
CONFIG_COMMON_LIBC_MALLOC=y
CONFIG_COMMON_LIBC_CALLOC=y
CONFIG_COMMON_LIBC_REALLOCARRAY=y
# CONFIG_COMMON_LIBC_REMOVE is not set
# CONFIG_PICOLIBC_USE_MODULE is not set
CONFIG_PICOLIBC_USE_TOOLCHAIN=y
# CONFIG_PICOLIBC_IO_FLOAT is not set
CONFIG_PICOLIBC_IO_LONG_LONG=y
CONFIG_STDOUT_CONSOLE=y
CONFIG_NEED_LIBC_MEM_PARTITION=y
# end of C Library

#
# C++ Language Support
#
# CONFIG_CPP is not set
# end of C++ Language Support

#
# Additional libraries
#

#
# Hash Function Support
#
# CONFIG_SYS_HASH_FUNC32 is not set
# end of Hash Function Support

#
# Hashmap (Hash Table) Support
#
# CONFIG_SYS_HASH_MAP is not set
# end of Hashmap (Hash Table) Support

#
# Heap and Memory Allocation
#
# CONFIG_SYS_HEAP_VALIDATE is not set
# CONFIG_SYS_HEAP_STRESS is not set
# CONFIG_SYS_HEAP_INFO is not set
CONFIG_SYS_HEAP_ALLOC_LOOPS=3
# CONFIG_SYS_HEAP_RUNTIME_STATS is not set
CONFIG_SYS_HEAP_ARRAY_SIZE=0
# CONFIG_SYS_HEAP_LISTENER is not set
# CONFIG_SYS_HEAP_SMALL_ONLY is not set
# CONFIG_SYS_HEAP_BIG_ONLY is not set
CONFIG_SYS_HEAP_AUTO=y
# CONFIG_MULTI_HEAP is not set
# CONFIG_SHARED_MULTI_HEAP is not set
# end of Heap and Memory Allocation

#
# Memory Blocks
#
# CONFIG_SYS_MEM_BLOCKS is not set
# end of Memory Blocks

CONFIG_NET_BUF=y
# CONFIG_NET_BUF_LOG is not set
# CONFIG_NET_BUF_LOG_LEVEL_OFF is not set
# CONFIG_NET_BUF_LOG_LEVEL_ERR is not set
# CONFIG_NET_BUF_LOG_LEVEL_WRN is not set
# CONFIG_NET_BUF_LOG_LEVEL_INF is not set
# CONFIG_NET_BUF_LOG_LEVEL_DBG is not set
CONFIG_NET_BUF_LOG_LEVEL_DEFAULT=y
CONFIG_NET_BUF_LOG_LEVEL=3
# CONFIG_NET_BUF_POOL_USAGE is not set
CONFIG_NET_BUF_ALIGNMENT=0

#
# OS Support Library
#
# CONFIG_FDTABLE is not set
CONFIG_ZVFS_OPEN_MAX=4
# CONFIG_PRINTK_SYNC is not set
CONFIG_MPSC_PBUF=y
# CONFIG_SPSC_PBUF is not set
# CONFIG_MPSC_CLEAR_ALLOCATED is not set
CONFIG_HAS_POWEROFF=y
# CONFIG_POWEROFF is not set
CONFIG_CBPRINTF_COMPLETE=y
# CONFIG_CBPRINTF_NANO is not set
CONFIG_CBPRINTF_FULL_INTEGRAL=y
# CONFIG_CBPRINTF_REDUCED_INTEGRAL is not set
# CONFIG_CBPRINTF_FP_SUPPORT is not set
# CONFIG_CBPRINTF_FP_A_SUPPORT is not set
# CONFIG_CBPRINTF_LIBC_SUBSTS is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_OFF is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_ERR is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_WRN is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_INF is not set
# CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_DBG is not set
CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL_DEFAULT=y
CONFIG_CBPRINTF_PACKAGE_LOG_LEVEL=3
# CONFIG_CBPRINTF_PACKAGE_LONGDOUBLE is not set
CONFIG_CBPRINTF_CONVERT_CHECK_PTR=y
# CONFIG_ZVFS is not set
# end of OS Support Library

#
# POSIX API Support
#

#
# POSIX Options
#
# CONFIG_POSIX_API is not set
CONFIG_POSIX_AEP_CHOICE_NONE=y
# CONFIG_POSIX_AEP_CHOICE_BASE is not set
# CONFIG_POSIX_AEP_CHOICE_PSE51 is not set
# CONFIG_POSIX_AEP_CHOICE_PSE52 is not set
# CONFIG_POSIX_AEP_CHOICE_PSE53 is not set
# CONFIG_POSIX_ASYNCHRONOUS_IO is not set
# CONFIG_POSIX_BARRIERS is not set
# CONFIG_POSIX_C_LANG_SUPPORT_R is not set
# CONFIG_POSIX_C_LIB_EXT is not set

#
# POSIX device I/O
#
# CONFIG_POSIX_DEVICE_IO is not set
CONFIG_POSIX_OPEN_MAX=4
# end of POSIX device I/O

# CONFIG_POSIX_FD_MGMT is not set
# CONFIG_POSIX_FILE_SYSTEM_R is not set
# CONFIG_POSIX_FILE_SYSTEM is not set

#
# POSIX memory
#
CONFIG_POSIX_PAGE_SIZE=0x40
# CONFIG_POSIX_SHARED_MEMORY_OBJECTS is not set
# CONFIG_POSIX_MAPPED_FILES is not set
# CONFIG_POSIX_MEMORY_PROTECTION is not set
# end of POSIX memory

# CONFIG_POSIX_MESSAGE_PASSING is not set
# CONFIG_POSIX_SINGLE_PROCESS is not set
# CONFIG_POSIX_MULTI_PROCESS is not set
# CONFIG_POSIX_THREADS is not set
# CONFIG_POSIX_READER_WRITER_LOCKS is not set

#
# POSIX scheduler options
#
# CONFIG_POSIX_PRIORITY_SCHEDULING is not set
# end of POSIX scheduler options

# CONFIG_POSIX_SEMAPHORES is not set

#
# POSIX signals
#
# CONFIG_POSIX_REALTIME_SIGNALS is not set
# CONFIG_POSIX_SIGNALS is not set
# end of POSIX signals

# CONFIG_POSIX_SPIN_LOCKS is not set

#
# POSIX synchronized I/O
#
# CONFIG_POSIX_FSYNC is not set
# CONFIG_POSIX_SYNCHRONIZED_IO is not set
# end of POSIX synchronized I/O

# CONFIG_POSIX_TIMERS is not set

#
# X/Open system interfaces
#
# CONFIG_XSI_REALTIME is not set
# CONFIG_XSI_SINGLE_PROCESS is not set
# CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_OFF is not set
# CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_ERR is not set
# CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_WRN is not set
# CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_INF is not set
# CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_DBG is not set
CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL_DEFAULT=y
CONFIG_XSI_SINGLE_PROCESS_LOG_LEVEL=3
# CONFIG_XOPEN_STREAMS is not set
# CONFIG_XSI_SYSTEM_LOGGING is not set
# CONFIG_XSI_THREADS_EXT is not set
# end of X/Open system interfaces

#
# Miscellaneous POSIX-related options
#
# CONFIG_EVENTFD is not set
# end of Miscellaneous POSIX-related options

CONFIG_TC_PROVIDES_POSIX_C_LANG_SUPPORT_R=y
# end of POSIX Options

#
# POSIX Shell Utilities
#
# end of POSIX Shell Utilities
# end of POSIX API Support

# CONFIG_OPENAMP_RSC_TABLE is not set
# CONFIG_SMF is not set
CONFIG_LIBGCC_RTLIB=y

#
# Utility Library
#
# CONFIG_JSON_LIBRARY is not set
CONFIG_RING_BUFFER=y
# CONFIG_RING_BUFFER_LARGE is not set
CONFIG_NOTIFY=y
# CONFIG_BASE64 is not set
CONFIG_ONOFF=y
# CONFIG_UTF8 is not set
# CONFIG_COBS is not set
# end of Utility Library

#
# Universally Unique Identifier (UUID)
#
# CONFIG_UUID is not set
# end of Universally Unique Identifier (UUID)

# CONFIG_MIN_HEAP is not set
# end of Additional libraries

#
# Subsystems and OS Services
#
# CONFIG_BINDESC is not set
CONFIG_BT=y
CONFIG_BT_HCI=y
# CONFIG_BT_CUSTOM is not set
CONFIG_BT_HCI_RAW=y
CONFIG_BT_HCI_RAW_H4=y
CONFIG_BT_HCI_RAW_H4_ENABLE=y
# CONFIG_BT_HCI_RAW_CMD_EXT is not set
CONFIG_BT_CONN_TX=y
# CONFIG_BT_LE_EXTENDED_FEAT_SET is not set
# CONFIG_BT_SCA_UPDATE is not set
# CONFIG_BT_TRANSMIT_POWER_CONTROL is not set
# CONFIG_BT_PATH_LOSS_MONITORING is not set
# CONFIG_BT_SUBRATING is not set
# CONFIG_BT_ISO_PERIPHERAL is not set
# CONFIG_BT_ISO_CENTRAL is not set
# CONFIG_BT_ISO_BROADCASTER is not set
# CONFIG_BT_ISO_SYNC_RECEIVER is not set

#
# Bluetooth buffer configuration
#
# end of Bluetooth buffer configuration

#
# Bluetooth Host
#

#
# Bluetooth Classic Options
#
# end of Bluetooth Classic Options
# end of Bluetooth Host

CONFIG_BT_CTLR_ENTROPY_SUPPORT=y
CONFIG_BT_CTLR_CRYPTO_SUPPORT=y
CONFIG_BT_CTLR_LE_ENC_SUPPORT=y
CONFIG_BT_CTLR_EXT_REJ_IND_SUPPORT=y
CONFIG_BT_CTLR_DATA_LEN_UPDATE_SUPPORT=y
CONFIG_BT_CTLR_PRIVACY_SUPPORT=y
CONFIG_BT_CTLR_EXT_SCAN_FP_SUPPORT=y
CONFIG_BT_CTLR_PHY_UPDATE_SUPPORT=y
CONFIG_BT_CTLR_PHY_2M_SUPPORT=y
CONFIG_BT_CTLR_PHY_CODED_SUPPORT=y
CONFIG_BT_CTLR_ADV_EXT_SUPPORT=y
CONFIG_BT_CTLR_ADV_EXT_CODING_SELECTION_SUPPORT=y
CONFIG_BT_CTLR_ADV_PERIODIC_SUPPORT=y
CONFIG_BT_CTLR_ADV_PERIODIC_RSP_SUPPORT=y
CONFIG_BT_CTLR_SYNC_PERIODIC_SUPPORT=y
CONFIG_BT_CTLR_SYNC_PERIODIC_RSP_SUPPORT=y
CONFIG_BT_CTLR_SYNC_TRANSFER_SENDER_SUPPORT=y
CONFIG_BT_CTLR_SYNC_TRANSFER_RECEIVER_SUPPORT=y
CONFIG_BT_CTLR_ADV_ISO_SUPPORT=y
CONFIG_BT_CTLR_SYNC_ISO_SUPPORT=y
CONFIG_BT_CTLR_CENTRAL_ISO_SUPPORT=y
CONFIG_BT_CTLR_PERIPHERAL_ISO_SUPPORT=y
CONFIG_BT_CTLR_CHAN_SEL_2_SUPPORT=y
CONFIG_BT_CTLR_SCA_UPDATE_SUPPORT=y
CONFIG_BT_CTLR_CONN_RSSI_SUPPORT=y
CONFIG_BT_CTLR_LE_POWER_CONTROL_SUPPORT=y
CONFIG_BT_CTLR_LE_PATH_LOSS_MONITORING_SUPPORT=y
CONFIG_BT_CTLR_SUBRATING_SUPPORT=y
CONFIG_BT_CTLR_FRAME_SPACE_UPDATE_SUPPORT=y
CONFIG_BT_CTLR_EXTENDED_FEAT_SET_SUPPORT=y
CONFIG_BT_CTLR_SHORTER_CONNECTION_INTERVALS_SUPPORT=y
CONFIG_HAS_BT_CTLR=y
CONFIG_BT_CTLR_HCI=y
CONFIG_BT_CTLR_HCI_NUM_CMD_PKT_MAX=1

#
# Bluetooth Controller configuration
#
CONFIG_BT_CTLR_ENTROPY=y
CONFIG_BT_CTLR_CRYPTO=y
CONFIG_BT_CTLR_HCI_VS_BUILD_INFO=""
# CONFIG_BT_CTLR_TX_PWR_PLUS_8 is not set
# CONFIG_BT_CTLR_TX_PWR_PLUS_7 is not set
# CONFIG_BT_CTLR_TX_PWR_PLUS_6 is not set
# CONFIG_BT_CTLR_TX_PWR_PLUS_5 is not set
# CONFIG_BT_CTLR_TX_PWR_PLUS_4 is not set
# CONFIG_BT_CTLR_TX_PWR_PLUS_3 is not set
# CONFIG_BT_CTLR_TX_PWR_PLUS_2 is not set
CONFIG_BT_CTLR_TX_PWR_0=y
# CONFIG_BT_CTLR_TX_PWR_MINUS_4 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_8 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_12 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_16 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_20 is not set
# CONFIG_BT_CTLR_TX_PWR_MINUS_40 is not set
CONFIG_BT_CTLR_TX_PWR_DBM=0
CONFIG_BT_CTLR_TX_PWR_ANTENNA=0
# CONFIG_BT_CTLR_TX_PWR_DYNAMIC_CONTROL is not set

#
# Bluetooth Controller features
#
CONFIG_BT_CTLR_LE_ENC=y
CONFIG_BT_CTLR_EXT_REJ_IND=y
CONFIG_BT_CTLR_LE_PING=y
CONFIG_BT_CTLR_DATA_LENGTH=y
CONFIG_BT_CTLR_PHY=y
CONFIG_BT_CTLR_CONN_RSSI=y
# CONFIG_BT_CTLR_LE_POWER_CONTROL is not set
CONFIG_BT_CTLR_FILTER_ACCEPT_LIST=y
CONFIG_BT_CTLR_PRIVACY=y
CONFIG_BT_CTLR_RL_SIZE=8
CONFIG_BT_CTLR_EXT_SCAN_FP=y
CONFIG_BT_CTLR_PHY_2M=y
CONFIG_BT_CTLR_PHY_CODED=y
CONFIG_BT_CTLR_CHAN_SEL_2=y
# CONFIG_BT_CTLR_ADV_EXT is not set
# CONFIG_BT_CTLR_SET_HOST_FEATURE is not set
# CONFIG_BT_CTLR_HCI_CODEC_AND_DELAY_INFO is not set
# CONFIG_BT_CTLR_SUBRATING is not set
# CONFIG_BT_CTLR_EXTENDED_FEAT_SET is not set
CONFIG_BT_CTLR_ASSERT_DEBUG=y
# CONFIG_BT_CTLR_ASSERT_HANDLER is not set
# CONFIG_BT_CTLR_VS_SCAN_REQ_RX is not set
# CONFIG_BT_EAD is not set

#
# Bluetooth logging
#

#
# Common
#
# end of Common

#
# Libraries
#
# end of Libraries

#
# Services
#
# end of Services
# end of Bluetooth logging

#
# Controller Area Network (CAN) bus subsystem
#
# end of Controller Area Network (CAN) bus subsystem

# CONFIG_CONSOLE_SUBSYS is not set
# CONFIG_CPU_LOAD_METRIC is not set
# CONFIG_CPU_LOAD_LOG_LEVEL_OFF is not set
# CONFIG_CPU_LOAD_LOG_LEVEL_ERR is not set
# CONFIG_CPU_LOAD_LOG_LEVEL_WRN is not set
# CONFIG_CPU_LOAD_LOG_LEVEL_INF is not set
# CONFIG_CPU_LOAD_LOG_LEVEL_DBG is not set
CONFIG_CPU_LOAD_LOG_LEVEL_DEFAULT=y
CONFIG_CPU_LOAD_LOG_LEVEL=3
# CONFIG_CRC is not set
# CONFIG_DAP is not set

#
# System Monitoring Options
#
CONFIG_THREAD_ANALYZER=y
# CONFIG_THREAD_ANALYZER_LOG_LEVEL_OFF is not set
# CONFIG_THREAD_ANALYZER_LOG_LEVEL_ERR is not set
# CONFIG_THREAD_ANALYZER_LOG_LEVEL_WRN is not set
# CONFIG_THREAD_ANALYZER_LOG_LEVEL_INF is not set
# CONFIG_THREAD_ANALYZER_LOG_LEVEL_DBG is not set
CONFIG_THREAD_ANALYZER_LOG_LEVEL_DEFAULT=y
CONFIG_THREAD_ANALYZER_LOG_LEVEL=3
# CONFIG_THREAD_ANALYZER_USE_LOG is not set
CONFIG_THREAD_ANALYZER_USE_PRINTK=y
CONFIG_THREAD_ANALYZER_ISR_STACK_USAGE=y
CONFIG_THREAD_ANALYZER_RUN_UNLOCKED=y
CONFIG_THREAD_ANALYZER_AUTO=y
CONFIG_THREAD_ANALYZER_AUTO_INTERVAL=60
CONFIG_THREAD_ANALYZER_AUTO_STACK_SIZE=1024
# CONFIG_THREAD_ANALYZER_AUTO_THREAD_PRIORITY_OVERRIDE is not set
# end of System Monitoring Options

#
# Debugging Options
#
# CONFIG_DEBUG is not set
# CONFIG_UBSAN is not set
# CONFIG_STACK_USAGE is not set
CONFIG_PRINTK=y
CONFIG_EARLY_CONSOLE=y
CONFIG_ASSERT_LEVEL=2
CONFIG_SPIN_VALIDATE=y
# CONFIG_FORCE_NO_ASSERT is not set
CONFIG_ASSERT_VERBOSE=y
# CONFIG_ASSERT_NO_FILE_INFO is not set
# CONFIG_ASSERT_NO_COND_INFO is not set
# CONFIG_ASSERT_NO_MSG_INFO is not set
# CONFIG_ASSERT_TEST is not set
# CONFIG_OVERRIDE_FRAME_POINTER_DEFAULT is not set
# CONFIG_DEBUG_THREAD_INFO is not set
# CONFIG_DEBUG_COREDUMP is not set
# CONFIG_SYMTAB is not set
# end of Debugging Options

# CONFIG_MIPI_STP_DECODER is not set
# CONFIG_CS_TRACE_DEFMT is not set
# CONFIG_CPU_LOAD is not set
CONFIG_CPU_LOAD_LOG_PERIODICALLY=0
# CONFIG_DISK_ACCESS is not set
# CONFIG_DSP is not set
# CONFIG_EMUL is not set
# CONFIG_CHARACTER_FRAMEBUFFER is not set

#
# File Systems
#
# CONFIG_FILE_SYSTEM_LIB_LINK is not set
# CONFIG_FILE_SYSTEM is not set
# end of File Systems

# CONFIG_GNSS_RTK is not set

#
# Inter Processor Communication
#
# CONFIG_RPMSG_SERVICE is not set
# CONFIG_IPC_SERVICE is not set
# end of Inter Processor Communication

# CONFIG_JWT is not set
# CONFIG_LLEXT is not set
# CONFIG_LLEXT_EDK is not set

#
# Logging
#
CONFIG_LOG_CORE_INIT_PRIORITY=0
CONFIG_LOG_MODE_DEFERRED=y
# CONFIG_LOG_MODE_IMMEDIATE is not set
# CONFIG_LOG_MODE_MINIMAL is not set
# CONFIG_LOG_FRONTEND is not set
# CONFIG_LOG_FRONTEND_OPT_API is not set
# CONFIG_LOG_CUSTOM_HEADER is not set
# CONFIG_LOG_MULTIDOMAIN is not set
CONFIG_LOG_FLUSH_SLEEP_US=10000

#
# Logging levels filtering
#
# CONFIG_LOG_RUNTIME_FILTERING is not set
CONFIG_LOG_DEFAULT_LEVEL=3
CONFIG_LOG_OVERRIDE_LEVEL=0
CONFIG_LOG_MAX_LEVEL=4
# end of Logging levels filtering

#
# Processing
#
CONFIG_LOG_PRINTK=y
CONFIG_LOG_MODE_OVERFLOW=y
# CONFIG_LOG_BLOCK_IN_THREAD is not set
CONFIG_LOG_PROCESS_TRIGGER_THRESHOLD=10
CONFIG_LOG_PROCESS_THREAD=y
CONFIG_LOG_PROCESS_THREAD_STARTUP_DELAY_MS=0
CONFIG_LOG_PROCESS_THREAD_SLEEP_MS=1000
# CONFIG_LOG_PROCESS_THREAD_CUSTOM_PRIORITY is not set
CONFIG_LOG_TRACE_SHORT_TIMESTAMP=y
# CONFIG_LOG_TIMESTAMP_64BIT is not set
# CONFIG_LOG_TIMESTAMP_USE_REALTIME is not set
# CONFIG_LOG_SPEED is not set
# end of Processing

#
# Output Formatting
#

#
# Prepend non-hexdump log message with function name
#
# CONFIG_LOG_FUNC_NAME_PREFIX_ERR is not set
# CONFIG_LOG_FUNC_NAME_PREFIX_WRN is not set
# CONFIG_LOG_FUNC_NAME_PREFIX_INF is not set
CONFIG_LOG_FUNC_NAME_PREFIX_DBG=y
# end of Prepend non-hexdump log message with function name

# CONFIG_LOG_MIPI_SYST_ENABLE is not set
# CONFIG_LOG_THREAD_ID_PREFIX is not set
# CONFIG_LOG_CUSTOM_FORMAT_SUPPORT is not set
# CONFIG_LOG_BACKEND_SHOW_COLOR is not set
CONFIG_LOG_TAG_MAX_LEN=0
CONFIG_LOG_BACKEND_SUPPORTS_FORMAT_TIMESTAMP=y
CONFIG_LOG_BACKEND_FORMAT_TIMESTAMP=y
CONFIG_LOG_OUTPUT_FORMAT_TIME_TIMESTAMP=y
# CONFIG_LOG_OUTPUT_FORMAT_LINUX_TIMESTAMP is not set
# CONFIG_LOG_OUTPUT_FORMAT_CUSTOM_TIMESTAMP is not set
# end of Output Formatting

#
# Backends
#
CONFIG_LOG_BACKEND_RTT=y
# CONFIG_LOG_BACKEND_RTT_MODE_DROP is not set
CONFIG_LOG_BACKEND_RTT_MODE_BLOCK=y
# CONFIG_LOG_BACKEND_RTT_MODE_OVERWRITE is not set
CONFIG_LOG_BACKEND_RTT_OUTPUT_TEXT=y
# CONFIG_LOG_BACKEND_RTT_OUTPUT_DICTIONARY is not set
# CONFIG_LOG_BACKEND_RTT_OUTPUT_CUSTOM is not set
CONFIG_LOG_BACKEND_RTT_OUTPUT_DEFAULT=0
CONFIG_LOG_BACKEND_RTT_OUTPUT_BUFFER_SIZE=16
CONFIG_LOG_BACKEND_RTT_RETRY_CNT=4
CONFIG_LOG_BACKEND_RTT_RETRY_DELAY_MS=5
CONFIG_LOG_BACKEND_RTT_BUFFER=0
CONFIG_LOG_BACKEND_RTT_FORCE_PRINTK=y
# CONFIG_LOG_BACKEND_SWO is not set
CONFIG_LOG_BACKEND_UART=y
# CONFIG_LOG_BACKEND_UART_ASYNC is not set
CONFIG_LOG_BACKEND_UART_BUFFER_SIZE=1
CONFIG_LOG_BACKEND_UART_AUTOSTART=y
CONFIG_LOG_BACKEND_UART_OUTPUT_TEXT=y
# CONFIG_LOG_BACKEND_UART_OUTPUT_DICTIONARY is not set
# CONFIG_LOG_BACKEND_UART_OUTPUT_CUSTOM is not set
CONFIG_LOG_BACKEND_UART_OUTPUT_DEFAULT=0
# CONFIG_LOG_BACKEND_IPC_SERVICE is not set
# end of Backends

#
# Misc
#
CONFIG_LOG_USE_VLA=y
CONFIG_LOG_SIMPLE_MSG_OPTIMIZE=y
# CONFIG_LOG_ALWAYS_RUNTIME is not set
# CONFIG_LOG_FMT_SECTION is not set
# CONFIG_LOG_FMT_STRING_VALIDATE is not set
# CONFIG_LOG_MEM_UTILIZATION is not set
CONFIG_LOG_FAILURE_REPORT_PERIOD=1000
# end of Misc

CONFIG_LOG_RATELIMIT=y
CONFIG_LOG_RATELIMIT_INTERVAL_MS=5000
CONFIG_LOG_OUTPUT=y
# end of Logging

CONFIG_MEM_ATTR=y
# CONFIG_MEM_ATTR_HEAP is not set

#
# Device Management
#

#
# Host command handler subsystem
#
# CONFIG_EC_HOST_CMD is not set
# end of Host command handler subsystem

# CONFIG_OSDP is not set
# end of Device Management

# CONFIG_MODBUS is not set
# CONFIG_MODEM_MODULES is not set

#
# Networking
#
# CONFIG_NETWORKING is not set
# end of Networking

#
# Power Management
#
# CONFIG_PM_POLICY_LATENCY_STANDALONE is not set
# end of Power Management

#
# Platform Management Communications Infrastructure (PMCI)
#
# CONFIG_MCTP is not set
# end of Platform Management Communications Infrastructure (PMCI)

#
# Portability
#
# end of Portability

# CONFIG_PROFILING is not set

#
# Random Number Generators
#
# CONFIG_TEST_RANDOM_GENERATOR is not set
CONFIG_TIMER_RANDOM_INITIAL_STATE=123456789
CONFIG_ENTROPY_DEVICE_RANDOM_GENERATOR=y
# CONFIG_XOSHIRO_RANDOM_GENERATOR is not set
CONFIG_CSPRNG_AVAILABLE=y
CONFIG_CSPRNG_ENABLED=y
CONFIG_HARDWARE_DEVICE_CS_GENERATOR=y
# end of Random Number Generators

# CONFIG_RTIO is not set

#
# SD
#
# CONFIG_MMC_STACK is not set
# CONFIG_SDMMC_STACK is not set
# CONFIG_SDIO_STACK is not set
# end of SD

# CONFIG_SECURE_STORAGE is not set
# CONFIG_SETTINGS is not set
# CONFIG_SHELL is not set
# CONFIG_STATS is not set

#
# Storage
#
# CONFIG_STREAM_FLASH is not set
# end of Storage

# CONFIG_TASK_WDT is not set

#
# Testing
#
# CONFIG_ZTEST is not set
# CONFIG_ZTEST_MOCKING is not set
# CONFIG_ZTRESS is not set
# CONFIG_TEST is not set
# CONFIG_FORCE_COVERAGE is not set
# CONFIG_TEST_USERSPACE is not set
# end of Testing

# CONFIG_TIMING_FUNCTIONS is not set
# CONFIG_TRACING is not set
# CONFIG_USB_DEVICE_STACK is not set
# CONFIG_USB_DEVICE_STACK_NEXT is not set
# CONFIG_USB_HOST_STACK is not set
# CONFIG_USBC_STACK is not set
# CONFIG_ZBUS is not set
# CONFIG_MODULES is not set
# end of Subsystems and OS Services

CONFIG_TOOLCHAIN_ZEPHYR_0_17=y
CONFIG_TOOLCHAIN_ZEPHYR_SUPPORTS_THREAD_LOCAL_STORAGE=y
CONFIG_TOOLCHAIN_ZEPHYR_SUPPORTS_GNU_EXTENSIONS=y

#
# Build and Link Features
#

#
# Linker Options
#
# CONFIG_LINKER_ORPHAN_SECTION_PLACE is not set
CONFIG_LINKER_ORPHAN_SECTION_WARN=y
# CONFIG_LINKER_ORPHAN_SECTION_ERROR is not set
CONFIG_FLASH_LOAD_SIZE=0
CONFIG_ROM_END_OFFSET=0
CONFIG_LD_LINKER_SCRIPT_SUPPORTED=y
CONFIG_LD_LINKER_TEMPLATE=y
# CONFIG_CMAKE_LINKER_GENERATOR is not set
# CONFIG_HAVE_CUSTOM_LINKER_SCRIPT is not set
CONFIG_LINKER_SORT_BY_ALIGNMENT=y

#
# Linker Sections
#
# CONFIG_LINKER_USE_BOOT_SECTION is not set
# CONFIG_LINKER_USE_PINNED_SECTION is not set
CONFIG_LINKER_GENERIC_SECTIONS_PRESENT_AT_BOOT=y
CONFIG_LINKER_LAST_SECTION_ID=y
CONFIG_LINKER_LAST_SECTION_ID_PATTERN=0xE015E015
CONFIG_LINKER_USE_RELAX=y
# end of Linker Sections

CONFIG_LINKER_ITERABLE_SUBALIGN=4
CONFIG_LINKER_DEVNULL_SUPPORT=y
# CONFIG_LINKER_DEVNULL_MEMORY is not set
# end of Linker Options

#
# Compiler Options
#
# CONFIG_STD_C90 is not set
CONFIG_STD_C99=y
# CONFIG_STD_C11 is not set
# CONFIG_STD_C17 is not set
# CONFIG_STD_C23 is not set
CONFIG_TOOLCHAIN_SUPPORTS_GNU_EXTENSIONS=y
# CONFIG_GNU_C_EXTENSIONS is not set
# CONFIG_CODING_GUIDELINE_CHECK is not set
# CONFIG_COMPILER_FREESTANDING is not set
CONFIG_SIZE_OPTIMIZATIONS=y
# CONFIG_SIZE_OPTIMIZATIONS_AGGRESSIVE is not set
# CONFIG_SPEED_OPTIMIZATIONS is not set
# CONFIG_DEBUG_OPTIMIZATIONS is not set
# CONFIG_NO_OPTIMIZATIONS is not set
# CONFIG_COMPILER_WARNINGS_AS_ERRORS is not set
# CONFIG_DEPRECATION_TEST is not set
# CONFIG_COMPILER_SAVE_TEMPS is not set
CONFIG_COMPILER_TRACK_MACRO_EXPANSION=y
CONFIG_COMPILER_COLOR_DIAGNOSTICS=y
# CONFIG_FORTIFY_SOURCE_NONE is not set
CONFIG_FORTIFY_SOURCE_COMPILE_TIME=y
# CONFIG_FORTIFY_SOURCE_RUN_TIME is not set
CONFIG_COMPILER_OPT=""
# CONFIG_MISRA_SANE is not set
CONFIG_TOOLCHAIN_SUPPORTS_VLA_IN_STATEMENTS=y
# end of Compiler Options

# CONFIG_ASSERT_ON_ERRORS is not set
# CONFIG_NO_RUNTIME_CHECKS is not set
CONFIG_RUNTIME_ERROR_CHECKS=y

#
# Build Options
#
CONFIG_KERNEL_BIN_NAME="zephyr"
CONFIG_OUTPUT_STAT=y
# CONFIG_OUTPUT_SYMBOLS is not set
CONFIG_OUTPUT_PRINT_MEMORY_USAGE=y
# CONFIG_CLEANUP_INTERMEDIATE_FILES is not set
CONFIG_BUILD_GAP_FILL_PATTERN=0xFF
# CONFIG_BUILD_NO_GAP_FILL is not set
# CONFIG_BUILD_OUTPUT_HEX_GAP_FILL is not set
# CONFIG_BUILD_OUTPUT_EXE is not set
# CONFIG_BUILD_OUTPUT_S19_GAP_FILL is not set
# CONFIG_BUILD_OUTPUT_UF2 is not set
# CONFIG_BUILD_OUTPUT_MOT is not set
# CONFIG_BUILD_OUTPUT_STRIPPED is not set
# CONFIG_BUILD_OUTPUT_COMPRESS_DEBUG_SECTIONS is not set
# CONFIG_BUILD_ALIGN_LMA is not set
# CONFIG_APPLICATION_DEFINED_SYSCALL is not set
# CONFIG_MAKEFILE_EXPORTS is not set
# CONFIG_BUILD_OUTPUT_META is not set
CONFIG_BUILD_OUTPUT_STRIP_PATHS=y
CONFIG_CHECK_INIT_PRIORITIES=y
# CONFIG_EMIT_ALL_SYSCALLS is not set
# end of Build Options

CONFIG_WARN_DEPRECATED=y
CONFIG_ENFORCE_ZEPHYR_STDINT=y
# end of Build and Link Features

#
# Boot Options
#
# CONFIG_IS_BOOTLOADER is not set
# CONFIG_BOOTLOADER_BOSSA is not set
# end of Boot Options

#
# Compatibility
#
CONFIG_LEGACY_GENERATED_INCLUDE_PATH=y
# end of Compatibility

Have you tried with v3.2.0 as well?

Best regards,

Vidar

[Burt]

Vidar, I have spent way too much time on this...no, I should not say that, because I found another "trick." I almost found a trick. It worked a few times. The trick was to hold down the reset button for several seconds, rather than a standard quick push and release. With a standard lets say half second click, the board almost always fails to succeed more than once. Hold it down for 4 or 5 seconds, and you might get 7 or 8 successful Bluetooth initializations before the controller initialization failure. 

It's too difficult to try to compare your .config files. You would have to provide the proven board files for nRF9160DK.

I don't know why we are getting such different results, but I have zero confidence in LPUART with Bluetooth. I hate to say it has no value, as I understand it to be a Nordic "special sauce". In our project, we will probably always use an nRF9160DK board for our Central, so low power is not very exciting. Regardless, I would have felt good if I presented a problem to you folks and, using brain power I don't have, the problem went away. But for practical purposes, we are perfectly fine using zephyr's hci_uart and eliminating the references to lpuart on the central_uart side. Interesting that the lpuart stuff is completely outside of standard Bluetooth HCI. I hope you will still try to replicate my problematic results--I don't even connect anything on the far side (perifpheral)--I just want to see the local side start reliably when continuously restarting at a short interval. Then I could look at stuff beyond that.

Burt

Hello
Starting Bluetooth Central UART sample
*** Booting nRF Connect SDK v3.2.0-5dcc6bd39b0f ***
*** Using Zephyr OS v4.2.99-a57ad913cf4e ***
Hello
Starting Bluetooth Central UART sample
*** Booting nRF Connect SDK v3.2.0-5dcc6bd39b0f ***
*** Using Zephyr OS v4.2.99-a57ad913cf4e ***
Hello
Starting Bluetooth Central UART sample
*** Booting nRF Connect SDK v3.2.0-5dcc6bd39b0f ***
*** Using Zephyr OS v4.2.99-a57ad913cf4e ***
Hello
Starting Bluetooth Central UART sample
*** Booting nRF Connect SDK v3.2.0-5dcc6bd39b0f ***
*** Using Zephyr OS v4.2.99-a57ad913cf4e ***
Hello
Starting Bluetooth Central UART sample
*** Booting nRF Connect SDK v3.2.0-5dcc6bd39b0f ***
*** Using Zephyr OS v4.2.99-a57ad913cf4e ***
Hello
ASSERTION FAIL [err == 0] @ WEST_TOPDIR/zephyr/subsys/bluetooth/host/hci_core.c:504
        Controller unresponsive, command opcode 0x0c03 timeout with err -11

I added the Hello at the beginning of main.

[Vidar Berg]

Hi Burt,

We have made some progress, but it has taken time to get there, and still the issue not fully resolved, unfortunately. The nRF9151 DK is what I had on hand when creating the project, but it "should" behave exactly like the nRF9160 DK in this case. I will see if I can find time to redo this using an nRF9160 DK after Christmas.

Best regards,

Vidar