Cannot Flash Thing53 using the debugger on a nrf52840DK with nrfConnect for Visual Studio Code

[lcj]

I am trying to flash and use the debugger on a nrf52840 DK to flash a Thingy53, using the ribbon connector as outlined in this video. I tried to follow the steps in this post:

1. Open nRF Connect for Desktop -> Programmer
2. Connect Thingy:53 and nRF52840 DK as in the image you uploaded.
   

   Yurii_B said:

   
3. Turn the thingy off. Turn on the DK.
4. Then press and hold SW2 (marked in pink, located next to SW3) while flipping SW1 to 'on''.
   
5. Verify that "Bootloader Thingy:53" is visible in Programmer. This indicates a bootlader is present

But I don't see the nrf5340 in my nrfConnect for Visual Studio Code:


Like it's shown in the video:

I get this error:

-- west flash: using runner nrfutil
-- runners.nrfutil: reset after flashing requested
-- runners.nrfutil: Flashing file: /Users/xxxxxxxxxx/Projects/xxxxxx/xxxxxx/xxxxxx/build_thingy53/merged_CPUNET.hex
Error: One or more batch tasks failed:
 * xxxxxxxxxx: Device error: Setting the debug port SELECT register failed while powering up sys and debug regions (Unknown Error in J-Link DLL (error code =-1)).
   
   This might indicate that the debug port is unavailable. Please double-check device power supply and SWD lines, and that SWD isn't disabled (Generic)

FATAL ERROR: command exited with status 1: nrfutil --json device x-execute-batch --batch-path /Users/xxxxxxxxxx/Projects/xxxxxx/xxxxxx/xxxxxx/build_thingy53/generated_nrfutil_batch.json --serial-number xxxxxxxxxx

When I use this command:

JLinkExe -device NRF5340_XXAA_APP -if SWD -speed 200

I get:

SEGGER J-Link Commander V8.90 (Compiled Nov 26 2025 17:27:22)
DLL version V8.90, compiled Nov 26 2025 17:26:30

Connecting to J-Link via USB...O.K.
Firmware: J-Link OB-nRF5340-NordicSemi compiled Jul  8 2025 10:15:34
Hardware version: V1.00
J-Link uptime (since boot): 0d 00h 38m 47s
S/N: XXX0XXXXXX
License(s): RDI, FlashBP, FlashDL, JFlash, GDB
USB speed mode: Full speed (12 MBit/s)
VTref=3.300V

When I type connect I get:

Device "NRF5340_XXAA_APP" selected.


Connecting to target via SWD
ConfigTargetSettings() start
ConfigTargetSettings() end - Took 8us
InitTarget() start
InitTarget() end - Took 139ms
ConfigTargetSettings() start
ConfigTargetSettings() end - Took 8us
InitTarget() start
InitTarget() end - Took 16.3ms
Error occurred: Could not connect to the target device.
For troubleshooting steps visit: https://kb.segger.com/J-Link_Troubleshooting

[Turbo J]

Not possible with some older DKs - they don't support the Cortex-M33 MCU cores:

This screenshot was taken with the NRF52840 DK clone from rigado.

Don't have a newer nordic nrf52840 DK here.

[lcj]

I just ordered another nrf5340 DK but this is my nrf52840dk:

[runsiv]

Hi Leo

It seems to be a bit of a mix here. So let's clarify what the goal is

1. Can you show me an image of your setup?

2. Is the goal here to remove the bootloader on the thingy or maybe restore it?

Regards

Runar

[lcj]

I want to flash and debug the Thingy53 from VS Code with the nrfConnect for VS Code Add-In like I do with a Development Kit.

[Turbo J]

Default firmware image may be locked.

Try west flash --recover or west flash --recover -r nrfjprog

Note that this will erase the bootloader from the device - it will be bricked until you can connect a debugger that supports Armv8-M. No idea if your DK does - it has the newer style debug chip which I am not familiar with.