• State Verified Answer
  • Replies 12 replies
  • Subscribers 62 subscribers
  • Views 6169 views
  • Users 0 members are here
Attachments (0)
Nordic Case Info
  • Case ID: 121237
Options
This post is older than 2 years and might not be relevant anymore
More Info: Consider searching for newer posts

Bricked Sparkfun nRF52832?

cswanson420

I have the nRF52DK board and I am using that to reprogram the Sparkfun breakout. However, initially, I was using the Sparkfun Beefy UART device to flash the nRF52832 to begin my SPI project using BLE.

What happened: Firstly, I did something dumb.

Not getting the SPI example to work on the breakout board, I started diminishing the example's main loop to toggle an LED. This, of course, was being done at 3:30AM and I connected the LED to pin 8 and then the board can not be flashed.

In fact, the board does not acknowledge the initial transmission from the nrfutil.py utility.

Onto the nRF52 DK:

I can read the memory on the affected breakout board using the pin 19 interface of the evaluation board. I can erase the memory and write new memory. I even went so far to purchase another breakout board, savebin 512KB of working flash memeory and loadbin this file onto the affected board:

Nothing.

Failed to upgrade target. Error is: No data received on serial port. Not able to proceed.

Possible causes:

  • bootloader, SoftDevice or application on target does not match the requirements in the DFU package.
  • baud rate or flow control is not the same as in the target bootloader.
  • target is not in DFU mode. If using the SDK examples, press Button 4 and RESET and release both to enter DFU mode.

Question:

Is there a low level checksum I can obtain that would indicate whether the board has a hardware failure?

Is the board truly bricked or can it be jump started somehow - like setting a PC register?

Is there a known flash bin file that will do some HelloWorld dance?

Destination green recycle?

Thanks

Parents
  • 0

    Hi, have you checked similar questions on the forum, e.g. this one? It's almost impossible to completely "brick" nRF5x chips, they should always be able to "recover" through Nordic tools like nRFgo Studio or nrfjprog with JTAG/SWD programmer (e.g. any Nordic nRF5x DK with SEGGER J-Link on board).

  • 0 in reply to endnode

    But actually you are right, there might be some UICR register values needed as well (if FW running on Sparkfun board uses it for storing some bootloader information or similar). You can dump UICR as well (at address 0x10001000, 0x210 bytes should be enough but maybe it will give you up to 4kB of data) and analyze it by using nRF52832 Product Specification (to filter "default" values from something what Sparkfun FW uses). I would assume that if certain FW needs some values in UICR it would have default values hardcoded and writes it to particular UICR registers if it detects them "empty" during boot sequence but developers of FW you are using might see it differently...

Reply
  • 0 in reply to endnode

    But actually you are right, there might be some UICR register values needed as well (if FW running on Sparkfun board uses it for storing some bootloader information or similar). You can dump UICR as well (at address 0x10001000, 0x210 bytes should be enough but maybe it will give you up to 4kB of data) and analyze it by using nRF52832 Product Specification (to filter "default" values from something what Sparkfun FW uses). I would assume that if certain FW needs some values in UICR it would have default values hardcoded and writes it to particular UICR registers if it detects them "empty" during boot sequence but developers of FW you are using might see it differently...

Children
No Data
Related