Package for BLE Secure DFU bootloader step by step guide for S132 PCA10040

[inghowe83]

Hi There,

I was trying to understand the step to create a test app for dfu bootloader update via BLE for PCA10040. Below is the documentation I read.

http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v14.2.0%2Fble_sdk_app_dfu_bootloader.html

I'm interested to further explore the Testing part by create my own firmware package for testing, and I not sure which example I could use for putting public key and generate the programming zip package.

Can I use the below package?

By the way, I tested flashing the dfu bootloader firmware which i have my public key place before generate the hex file.

Guide: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk52.v0.9.2%2Fbledfu_example_running.html

Example: 

I received flashing error as below.

Mind to share similar document as the following link for S132 PCA10040? It would be much appreciated.

devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader

[Bjørn Kvaale]

I would suggest following the secure dfu blog post that you posted at the bottom. It works for your PCA10040 board. An easy way to get started is just by updating the application on the nrf52 PCA10040 DK. The application you could update could be the Blinky example located at: nRF5_SDK_14.2.0_17b948a\examples\peripheral\blinky\pca10040\s132\ses\

Just follow the blog post & finish steps A to D. At the end, you should notice that the LEDs on your board start blinking one after the other in a loop. Then, you know that the DFU has been successful. 

[inghowe83]

Hi Bjørn Kvaale

I test the step and program the softdevices using the following command.

nrfjprog --program C:\nRF5_SDK_14.2.0_17b948a\components\softdevice\s132\hex\s132_nrf52_5.0.0_softdevice.hex --verify --chiperase -f NRF52
nrfjprog --program C:\nRF5_SDK_14.2.0_17b948a\examples\dfu\bootloader_secure_ble\pca10040\ses\Output\Release\Exe\secure_dfu_ble_s132_pca10040.hex --verify -f NRF52

I notice the DfuTarg won't appear if I use nrfjprog to program the bootloader, while the dfutarg works for segger build and run option.

[Bjørn Kvaale]

It should work with both segger embedded studio & using nrjprog. It seems like both of your nrfjprog commands are correct. Are you getting any error messages when you run the nrfjprog commands? Or does everything build correctly, only that the bootloader does not advertise? I'm guessing you remembered to compile the bootloader with the correct public key & used the built hex file in your second nrfjprog command, right?

Which version of nrfjprog are you using?

[inghowe83]

Hi Bjørn Kvaale

Here is my reply.

Are you getting any error messages when you run the nrfjprog commands?

Ans: No errors

Or does everything build correctly, only that the bootloader does not advertise?

Ans: Yes my segger compiler output should build complete, the bootloader does not advertise. I have try to push button 4 and reset the PCA10040

I'm guessing you remembered to compile the bootloader with the correct public key & used the built hex file in your second nrfjprog command, right?

Ans: Yes, I followed the step in the blog to build and I replace the dfu_public_key and regenerate the private_key

Which version of nrfjprog are you using?

Ans:

nrfjprog version: 9.7.2
JLinkARM.dll version: 6.22d

[Bjørn Kvaale]

As stated in the Nordic Infocenter:

Important: This version of the nrfjprog executable has been developed and tested for SEGGER software, JLink_V612a. It will most likely work with other versions of the SEGGER software, but keep in mind that there could be major changes that break the compatibility.

Could you try testing with Jlink v6.12 to see if that fixes the issue?

[inghowe83]

Hi Bjørn Kvaale

Thanks. But where can I obtain Jlink v6.12a? The seggar website only provides the latest Jlink.