ST7735 interfacing instructions

[Raja]

After going through the SDK i came across the ST7735 LCD screen example.

On the SDK Page it says example uses the ILI9341 controller, But we can also configure it to use the ST7735 controller. After looking into sdk_config.h it is already enabled as:

// <e> ST7735_ENABLED - st7735 - ST7735R TFT controller
//==========================================================
#ifndef ST7735_ENABLED
#define ST7735_ENABLED 1
#endif

Do i need configure it some where else other than this?

Also wiring is not very clear, can some one point me how wire it with nRF52-DK with ST7735.

link

[Edvin]

Hello,

I am not familiar with this device, but you have to change the SPI driver to match the ST7735.

 

In main.c on line 82:

static const nrf_lcd_t * p_lcd = &nrf_lcd_ili9341;

change this to:

static const nrf_lcd_t * p_lcd = &nrf_lcd_st7735;

And the p_lcd pointer should use the ST LCD screen instead of the ili9341 LCD.

 

I am not sure about the wiring. It seems like the defines from the sdk_config seems right, where did you find the numbers in the picture to the right?

Pin 10 (CS)
Pin 08 (SDA
Pin 09 (SCK)

?

I would give this a go:

NRF:                             ST_LCD (not the ones marked "SD", but the others) :

22.................................CS

23.................................SDA

24................................. --

25.................................SCK

19 (DC)........................??

 

I am not sure whether the DC is needed. See this thread, where DC is explained. I am not sure, but I suspect that the DC is supposed to be connected to AO. (see this thread)

 

Best regards,

Edvin

[Raja]

Hi Ediv, i tried to match the pins from sdk_config.h with LCD board. So not sure if they are right but will try it today.

But to which pin should i connect the MISO pin 24 of nRF52-DK to lcd?

[Raja]

Thank you very much for your kind help Edvin. It has worked final pins are:

nRF52-DK	SainSmart
25	SCL
23	SDA
22	CS
19	RS/DC
vdd	RES
5V	VCC
Gnd	GND

Pin 24 not needed.

I used this LCD

[Raja]

It is not working anymore. It was working last night now when i switched on the board white screen appears. I initially thought that LCD is broken so tested it on arduino with adafruit library that worked screen started working after i pressed reset button on arduino nano. 

Then i plugged back lcd for nRF52-DK hoping it will work but it did not work. I pressed reset button even reprogrammed firmware few times but it does not work anymore. It prints the log message on putty but LCD does not work with nRF52-DK now.

Where as when i plug it on arduino LCD works fine after pressing reset button. Not sure what has gone wrong with it now.

(Also i have found when i just connect scl and sda to LCD from arduino it turns on the white screen. But this does not happen on nRF52-DK.)

[Edvin]

Hello,

Not sure, but it might be that it can't deliver enough power if you are using a USB hub. Can you try to connect the USB cable that your DK is connected to directly into the computer?

BR,

Edvin

[Raja]

Hi Edwin, i have checked vcc power is sufficient. Also it is not connected to hub but directly on machine. I am really puzzled what is wrong it was working one day next day it stopped working without any change.

Are we sure RESET pin needs to be connected to VDD? 

I have purchased few other LCD none of them works now. Do i need to power up the scl, sda, dc, cs pin to 5 v like arduino?

What LCD was used in the GFX example at nordic? I can buy and try that.

[Edvin]

You don't have a logic analyzer, like the saleae logic analyzer, by chance? It would be interresting to see if there are any difference between SDA (MOSI) on the Arduino and the nRF. 

 

regarding the RESET, I am not sure how it behaves. You have to check the datasheet of your screen whether it needs to be grounded or connected to VDD. I believe VDD is typical for these kind of pins. That means that when the pin gets a GND pulse, it will reset.

 

As you can see here, it uses the ILI9341.

 

Are you sure that there were no changes between the time that it was working and now? Can you try to unzip the SDK again and try with an unmodified version of the example? (only with the changes described to change to the ST LCD screen).

 

BR,

Edvin

[Raja]

Thanks for advice I have purchased it now, will receive it soon. Will test it and send the difference here.