stop and restart SAADC to power saving

[mdido]

Hello, I'm using softdevice 6.0 and SDK 15.

In my application, I would like stop the SAADC at the disconnection and then restart SAADC at the connection to power saving.

To start SAADC I use this code:

void saadc_init(void)
{
    ret_code_t err_code;

    err_code = nrf_drv_saadc_init(NULL, saadc_callback);
    APP_ERROR_CHECK(err_code);

    err_code = nrf_drv_saadc_channel_init(0, &channel_config_PRESSURE);
    APP_ERROR_CHECK(err_code);

    err_code = nrf_drv_saadc_buffer_convert(m_buffer_pool[0], SAMPLES_IN_BUFFER);
    APP_ERROR_CHECK(err_code);

 }

To launch a sampling I use the call:

nrf_drv_saadc_sample();

To stop the SAADC I use the call:

nrf_drv_saadc_uninit()

The problem is that after the stop the interrupt handler of SAADC no longer works.

The code for interrupt handler is the following:

void saadc_callback(nrf_drv_saadc_evt_t const * p_event)
{
  nrf_saadc_value_t adc_result;
  uint16_t pressure_mV_local;
  uint16_t pressure_mV_acc;
  int i;
  char debug_str[10] = {0};

    if (p_event->type == NRF_DRV_SAADC_EVT_DONE)
    {
        ret_code_t err_code;

        err_code = nrf_drv_saadc_buffer_convert(p_event->data.done.p_buffer, SAMPLES_IN_BUFFER);
        APP_ERROR_CHECK(err_code);

        adc_result = p_event->data.done.p_buffer[0];

    }
}

What is the correct procedure to stop and then to restart the SAADC?

Thanks

 

[Einar Thorsrud]

Hi,

It is fine to call nrf_drv_saadc_uninit() as you do, but then you also have to initialize everything again before the next use. iI is not clear to me whether you do that or not? If not, you should get an assert from the driver if you have built the application with the DEBUG_NRF preprocessor define set (used by default in the Debug target for SES projects in the SDK).

If this is not the problem, can you explain in more detail what you do and how the "interrupt handler of SAADC no longer works"?

[mdido]

Hello,the sequence of the operation is:

connection

saadc_init

nrf_drv_saadc_sample

saadc interrupt handler is triggered

disconnection

nrf_drv_saadc_uninit

connection

saadc_init

nrf_drv_saadc_sample

but at this point the saadc interrupt handler is not triggerd; SDK returns no error

Best regards

[Einar Thorsrud]

Hi,

You are right that if you don't wait for the sampling to finish before disabling you will never get any samples (in the code snippet in my previous answer you can see this by commenting out 78). This is because you uninitialize the driver before sampling has finished, so you never actually get the callback with the sample.

If this is what you are seeing, then I would say you have a bug in your code, as you uninitialize the driver before you are done using it (have not yet received the sample).

[mdido]

Ok, that's all clear.

Thank you for the support

Best regards

[mdido]

Hello, I used a semaphore in saadc_callback and I wait until is cleared before of saadc_unint. If Optimization level is setted "none" everything works fine, but if I set Optimization level as "Optimize for size" seems that micro does not exit from the saadc callback. Do you have any suggest?

Best regards

[Einar Thorsrud]

Hi,

This sounds like a typical thing you could see if the semaphore is not volatile. Is it?

[mdido]

Hello,

you're right. The semaphore was not volatile. Thank you for the quick support.

Best regards