Related to BLE lon range

[Alan Ajit]

Dear nordic

I changed my BLE application to coded phy for long range (chip used nrf52840) . application works fine(debug). 

But i cant see any advertising  in smart phone BLE appliation's 

I need a help to see my device advertising packet . I think device advertising has no problem but its not seen in smart phones  

can you help me to find out why smart phone not detect the advertisings.

is it any other way to find device properly advertise or not?

need some helps

[awneil]

What smart phones?

And running what operating system(s)?

And what version(s) ?

Do the phones and/or operating systems support BT 5 features?

blog.bluetooth.com/exploring-bluetooth-5-going-the-distance

[Alan Ajit]

SDK 15 are used in device

Android 8.0 and Bluetooth 5 are also supported

Nothing will see in phones but code works fine no hangs this is for coded phy

but in 1mb phy phone get advertising and find device 

i don't know where the problem (device side or phone side)? i need some help to solve this

[Alan Ajit]

Thanks for your reply i need one more help i tested BLE central relay example for long range 

i dont know it is right procedure to setting

can you check that?

I changed in ble_advertising .c like below(bolded below)

uint32_t ble_advertising_init(ble_advertising_t * const p_advertising,
ble_advertising_init_t const * const p_init)
{
uint32_t ret;
if ((p_init == NULL) || (p_advertising == NULL))
{
return NRF_ERROR_NULL;
}
if (!config_is_valid(&p_init->config))
{
return NRF_ERROR_INVALID_PARAM;
}

p_advertising->adv_mode_current = BLE_ADV_MODE_IDLE;
p_advertising->adv_modes_config = p_init->config;
p_advertising->conn_cfg_tag = BLE_CONN_CFG_TAG_DEFAULT;
p_advertising->evt_handler = p_init->evt_handler;
p_advertising->error_handler = p_init->error_handler;
p_advertising->current_slave_link_conn_handle = BLE_CONN_HANDLE_INVALID;
p_advertising->p_adv_data = &p_advertising->adv_data;

memset(&p_advertising->peer_address, 0, sizeof(p_advertising->peer_address));

// Copy advertising data.
if (!p_advertising->initialized)
{
p_advertising->adv_handle = BLE_GAP_ADV_SET_HANDLE_NOT_SET;
}
p_advertising->adv_data.adv_data.p_data = p_advertising->enc_advdata;
p_advertising->adv_data.adv_data.len = BLE_GAP_ADV_SET_DATA_SIZE_MAX;

ret = ble_advdata_encode(&p_init->advdata, p_advertising->enc_advdata, &p_advertising->adv_data.adv_data.len);
VERIFY_SUCCESS(ret);

if (&p_init->srdata != NULL)
{
p_advertising->adv_data.scan_rsp_data.p_data = p_advertising->enc_scan_rsp_data;
p_advertising->adv_data.scan_rsp_data.len = BLE_GAP_ADV_SET_DATA_SIZE_MAX;

ret = ble_advdata_encode(&p_init->srdata,
p_advertising->adv_data.scan_rsp_data.p_data,
&p_advertising->adv_data.scan_rsp_data.len);
VERIFY_SUCCESS(ret);
}
else
{
p_advertising->adv_data.scan_rsp_data.p_data = NULL;
p_advertising->adv_data.scan_rsp_data.len = 0;
}

// Configure a initial advertising configuration. The advertising data and and advertising
// parameters will be changed later when we call @ref ble_advertising_start, but must be set
// to legal values here to define an advertising handle.
p_advertising->adv_params.primary_phy = BLE_GAP_PHY_CODED;
p_advertising->adv_params.duration = p_advertising->adv_modes_config.ble_adv_fast_timeout;
p_advertising->adv_params.properties.type = BLE_GAP_ADV_TYPE_EXTENDED_CONNECTABLE_NONSCANNABLE_UNDIRECTED;
p_advertising->adv_params.p_peer_addr = NULL;
p_advertising->adv_params.filter_policy = BLE_GAP_ADV_FP_ANY;
p_advertising->adv_params.interval = p_advertising->adv_modes_config.ble_adv_fast_interval;

ret = sd_ble_gap_adv_set_configure(&p_advertising->adv_handle, NULL, &p_advertising->adv_params);
VERIFY_SUCCESS(ret);

p_advertising->initialized = true;
return ret;
}

above two line i changed 

 is it any wrong in my procedure i need some help

[awneil]

how to properly post source code:

[Alan Ajit]

uint32_t ble_advertising_init(ble_advertising_t            * const p_advertising,
                              ble_advertising_init_t const * const p_init)
{
    uint32_t ret;
    if ((p_init == NULL) || (p_advertising == NULL))
    {
        return NRF_ERROR_NULL;
    }
    if (!config_is_valid(&p_init->config))
    {
        return NRF_ERROR_INVALID_PARAM;
    }

    p_advertising->adv_mode_current               = BLE_ADV_MODE_IDLE;
    p_advertising->adv_modes_config               = p_init->config;
    p_advertising->conn_cfg_tag                   = BLE_CONN_CFG_TAG_DEFAULT;
    p_advertising->evt_handler                    = p_init->evt_handler;
    p_advertising->error_handler                  = p_init->error_handler;
    p_advertising->current_slave_link_conn_handle = BLE_CONN_HANDLE_INVALID;
    p_advertising->p_adv_data                     = &p_advertising->adv_data;

    memset(&p_advertising->peer_address, 0, sizeof(p_advertising->peer_address));

    // Copy advertising data.
    if (!p_advertising->initialized)
    {
        p_advertising->adv_handle = BLE_GAP_ADV_SET_HANDLE_NOT_SET;
    }
    p_advertising->adv_data.adv_data.p_data = p_advertising->enc_advdata;
    p_advertising->adv_data.adv_data.len    = BLE_GAP_ADV_SET_DATA_SIZE_MAX;

    ret = ble_advdata_encode(&p_init->advdata, p_advertising->enc_advdata, &p_advertising->adv_data.adv_data.len);
    VERIFY_SUCCESS(ret);

    if (&p_init->srdata != NULL)
    {
        p_advertising->adv_data.scan_rsp_data.p_data = p_advertising->enc_scan_rsp_data;
        p_advertising->adv_data.scan_rsp_data.len    = BLE_GAP_ADV_SET_DATA_SIZE_MAX;

        ret = ble_advdata_encode(&p_init->srdata,
                                  p_advertising->adv_data.scan_rsp_data.p_data,
                                 &p_advertising->adv_data.scan_rsp_data.len);
        VERIFY_SUCCESS(ret);
    }
    else
    {
        p_advertising->adv_data.scan_rsp_data.p_data = NULL;
        p_advertising->adv_data.scan_rsp_data.len    = 0;
    }

    // Configure a initial advertising configuration. The advertising data and and advertising
    // parameters will be changed later when we call @ref ble_advertising_start, but must be set
    // to legal values here to define an advertising handle.
    p_advertising->adv_params.primary_phy     = BLE_GAP_PHY_CODED;
    p_advertising->adv_params.duration        = p_advertising->adv_modes_config.ble_adv_fast_timeout;
    p_advertising->adv_params.properties.type = BLE_GAP_ADV_TYPE_EXTENDED_CONNECTABLE_NONSCANNABLE_UNDIRECTED;
    p_advertising->adv_params.p_peer_addr     = NULL;
    p_advertising->adv_params.filter_policy   = BLE_GAP_ADV_FP_ANY;
    p_advertising->adv_params.interval        = p_advertising->adv_modes_config.ble_adv_fast_interval;

    ret = sd_ble_gap_adv_set_configure(&p_advertising->adv_handle, NULL, &p_advertising->adv_params);
    VERIFY_SUCCESS(ret);

    p_advertising->initialized = true;
    return ret;
}

just change phy and type.

[Marjeris Romero]

Hi,

I think this will work. Have you try to test it?

And if you haven't had a look at it I will post the link to our long range demo with nRF52840 DK here.

In the demo the secondary phy was also set to BLE_GAP_PHY_CODED. You can read more about advertising in Bluetooth 5 in this blog post.

If it doesn't work just let med know and I will try to implement long range with the relay example myself on Monday.

Best Regards,

Marjeris

[Alan Ajit]

Thanks for your support i tested but its not working so i debugged the program and check current phy

I found that the phy automatically changes to 1mb phy i need some help to solve this 

The problem i have no DK board i have only my own custom board i tested with my custom board so i want to change in relay application to get long range if any wrong in my procedure(code)  it is very difficult to find because i have no DK board. so need some help to implement long range

[Marjeris Romero]

Hi Alan,

I will take a look at how to implement long range in the relay example for your application and try to help you as good as I can. But could you open a new ticket for this question? Since it can get messy and the original post was about not seeing the device advertising with your smartphone.

Best Regards,

Marjeris

[Alan Ajit]

Thanks for replay new ticket are open now. I need some help to achieve this

[awneil]

So how about giving a link to it, then?

[Alan Ajit]

This is the link of new ticket

https://devzone.nordicsemi.com/f/nordic-q-a/39718/how-to-implement-long-range-in-ble-central-peripheral-example-relay

[awneil]

Alan Ajit said:

it is very difficult to find because i have no DK board

Surely, the answer to that is to get a DK board!

This is exactly why Nordic - and all the others - make Development Boards!

Using a DK (or DKs) gives you 2 key advantages:

1. You have a known-good working platform
2. It's a standard platform - so everyone knows what you're talking about, and can reproduce your setup.