Migrating a design from Raspberry pi Zero to nRF9160 DK - Need I2C and SPI interfaces

[RodWatt]

Hi,

I have developed a simple system based around a Raspberry Pi Zero. The system uses a couple of sensors to measure temperature and water pressure using a ADS51115 A/D and a MAX 31865 RTD to digital convertor. These connect to the Pi zero via the !2C bus and the SPI interface. I would like to replace the Pi zero with the nRF9160 dev board, can some one point me to some example hw and sw that will enable me to quickly convert. Thanks, Rod

[Jan Tore Guggedal]

Hi, RodWatt

In order to use SPI and I2C peripherals, the following configurations can be placed in `prj.conf` to enable them and select the nrfx driver:

CONFIG_I2C=y
CONFIG_I2C_NRFX=y
CONFIG_I2C_2=y
CONFIG_I2C_2_NRF_TWIM=y

CONFIG_SPI=y
CONFIG_SPI_NRFX=y
CONFIG_SPI_3=y
CONFIG_SPI_3_NRF_SPIM=y

This will enable I2C instance 2 and SPI instance 3, configure them to use nrfx driver. Note that these are the ones declared in the default secure boot to be available for a non-secure application:
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160/secure_boot/src/main.c#L321

You can choose other instances as long as you also adjust which peripherals are set as non-secure.

You then need to defined the peripherals in an overlay file for the board where you can set the pin numbers and clock speed. Name it `nrf9160_pca10090.overlay` and place it in the application folder. The contents of the file may be as follows:

&i2c2 {
        status = "ok";
        sda-pin = <30>;
        scl-pin = <31>;
        clock-frequency = <I2C_BITRATE_FAST>;
};

&spi3 {
        status = "ok";
        sck-pin = <6>;
        mosi-pin = <7>;
        miso-pin = <8>;
        spi-max-frequency = <4000000>;
};

The devices get the labels "I2C_2" and "SPI_3" to be used in the `device_get_binding()` call, according to their instance numbers.

When you have the configuration set, you will be able to use the generic I2C and SPI drivers in Zephyr, and can build use those samples and the API documentation as reference:

I2C API:
https://docs.zephyrproject.org/latest/api/io_interfaces.html?#i2c-interface

SPI API:
https://docs.zephyrproject.org/latest/api/io_interfaces.html?#spi-interface

Samples:
https://github.com/zephyrproject-rtos/zephyr/tree/master/samples/drivers 

[RodWatt]

Jan, thank you for your reply. A couple  of follow on questions.

1. Am I correct in saying that I can assign any GPIO pins as SPI and I2C interfaces?

2. As part of my development process, I want to phase in the replacement of the Raspberry Pi. In the next version on the prototype, I would like to keep the Pi zero and add the nRF9160DK effectively as a peripheral. 

So, please can you advise how I can add the nRF9160DK as a peripheral to the Pi. Do I just connect over UART or can you suggest a better way?

[RodWatt]

Thanks Jan,

OK, I have created an overly file, nrf9160_pca10090.overlay and have added the code as detailed in your message above. This is in my application directory

Watts-MacBook-Pro:BME280_Test_Code Watt$ ls

CMakeLists.txt prj_spi.conf

build sample.yaml

nrf9160_pca10090.overlay src

prj.conf

When I try to build

cmake -GNinja -DSHIELD=nrf9160_pca10090 -DBOARD=nrf9160_pca10090 ..

I get an error

Zephyr version: 1.14.0

-- Found PythonInterp: /usr/local/bin/python3 (found suitable version "3.7.3", minimum required is "3.4") 

-- Selected BOARD nrf9160_pca10090

No shield named 'nrf9160_pca10090' found

Any ideas?

[Jan Tore Guggedal]

Hi,

I might be misunderstanding here, but it looks liek you're trying to use another nRF91 DK as a shield. If you build without the -DSHIELD option, this should work. If you have a (BME280?) shield connected to your board, you can create an overlay with its name like you did for the board. Then you can feed the shield name into the build system using -DSHIELD. 

Please correct me if I'm not understanding what you want to achieve.

Best regards,

Jan Toe

[RodWatt]

Hi Jan,

Replying to this as your latest comments don't have an associated reply button.

Yes, I am connecting the BME280 to the 9160 DK. As per your previous reply, I created an overlay file, which I called nrf9160_pca10090.overlay and added the I2C and SPI code above.

I then try to build this with the command

cmake -GNinja -DSHIELD=nrf9160_pca10090 -DBOARD=nrf9160_pca10090 ..

I get an error

Zephyr version: 1.14.0

-- Found PythonInterp: /usr/local/bin/python3 (found suitable version "3.7.3", minimum required is "3.4") 

-- Selected BOARD nrf9160_pca10090

No shield named 'nrf9160_pca10090' found

So, are you suggesting that I create a shield called BME280.overlay which contain the I2C and SPI code above and then build using

cmake -GNinja -DSHIELD=BME280 -DBOARD=nrf9160_pca10090 ..

Regards,

Rod

Sorry, I thought I ad replied to this earlier, but my replay seems to have disappeared. 

[Jan Tore Guggedal]

Hi,

I'd just remove the -DSHIELD altogether, as you've already added the BME280 to the PCA10090 overlay. You can also define which pins to use as shown in an earlier reply in this thread in that same overlay. The alternative is as you mention to add an overlay called bme280.overlay and set -DSHIELD=bme280.

Regards,

Jan Tore

[RodWatt]

Hi Jan,

OK, that works!

Cheers