This post is older than 2 years and might not be relevant anymore
More Info: Consider searching for newer posts

How optimize high current consumption in sleep mode using nRF52840?

Hello to all,

We have developed our application & the following platform we are using:

  • SDK 15.0, Segger IDE on windows PC
  • Softdevice version is 6.0.0
  • Hardware version nRF52840 SoC.
  • Our product is battery operated, so high power consumption is serious an issue for us.

In our application we have used ble_app_uart example with SAADC because our sensor is analog. We also made custom PCB using nRF52840 and it working well not an issue. But our problem is very too much high current consumption is sleep mode means system OFF mode.

Here is below measured analysis with the help of Nordic Power Profile kit:

  1. The average current consumption while advertising is 962uA - 1.62mA I think this is OK.
  2. The average current consumption when sensor device enter into sleep mode is 562uA (Which is very high)

We have disabled all used peripheral before enter device into sleep mode as like below:

void sleep_mode_enter() {
  uint32_t err_code;
  NRF_LOG_INFO("Sleep mode Enter");
  flash_data_sending = false;
  start_measurement = false;
  nrf_gpio_pin_clear(SENSOR_PIN);  // OFF Sensor
  nrf_gpio_pin_set(GREEN_LED_PIN); // OFF Green LED
  nrf_gpio_pin_set(BLUE_LED_PIN);  // OFF BLUE LED
  stop_adc();
  err_code = app_uart_close();
  APP_ERROR_CHECK(err_code);
  NRF_LOG_INFO("UART close: %d", err_code);
}

void stop_adc() {
  nrf_drv_timer_disable(&m_timer);
  nrf_drv_timer_uninit(&m_timer);
  nrf_drv_ppi_channel_disable(m_ppi_channel);
  nrf_drv_ppi_uninit();
  NRF_SAADC->TASKS_STOP = 1;
  nrf_drv_saadc_uninit();
}

We have tested our hardware and sure this not hardware problem because when our device enter into deep sleep mode system OFF that time the current consumption near about 0.7uA to 1uA. Even when our designed firmware upload into nRF52840 DK and measured consumption using PPK that time got same results.

Questions:

  1. Why this too much very high power consumption getting in sleep mode?
  2. Is any wrong in our sleep mode enter function and disabled module functions?

Will you please suggest any solution, We should need to optimize this consumption to increase battery life because our sensor devices is battery operated.

Looking forward your response..!!

Thanks in advanced..!! 

Parents
  • Hi

    Do you call a sleep mode function after disabling all your functions, because I can't see that you set sd_power_system_off() anywhere in the attached code snippet. If not, your device will still be on, just not do anything. See this sleep mode enter function for reference:

    /**@brief Function for putting the chip into sleep mode.
     *
     * @note This function will not return.
     */
    static void sleep_mode_enter(void)
    {
        ret_code_t err_code;
    
        err_code = bsp_indication_set(BSP_INDICATE_IDLE);
        APP_ERROR_CHECK(err_code);
    
        // Prepare wakeup buttons.
        err_code = bsp_btn_ble_sleep_mode_prepare();
        APP_ERROR_CHECK(err_code);
    
        // Go to system-off mode (this function will not return; wakeup will cause a reset).
        err_code = sd_power_system_off();
        APP_ERROR_CHECK(err_code);
    }

    Best regards,

    Simon

Reply
  • Hi

    Do you call a sleep mode function after disabling all your functions, because I can't see that you set sd_power_system_off() anywhere in the attached code snippet. If not, your device will still be on, just not do anything. See this sleep mode enter function for reference:

    /**@brief Function for putting the chip into sleep mode.
     *
     * @note This function will not return.
     */
    static void sleep_mode_enter(void)
    {
        ret_code_t err_code;
    
        err_code = bsp_indication_set(BSP_INDICATE_IDLE);
        APP_ERROR_CHECK(err_code);
    
        // Prepare wakeup buttons.
        err_code = bsp_btn_ble_sleep_mode_prepare();
        APP_ERROR_CHECK(err_code);
    
        // Go to system-off mode (this function will not return; wakeup will cause a reset).
        err_code = sd_power_system_off();
        APP_ERROR_CHECK(err_code);
    }

    Best regards,

    Simon

Children
  • Thanks for fast reply...

    Yes this function has for enter device into deep sleep mode like same as you provided:

    void deep_sleep_mode_enter(void) {
      NRF_LOG_INFO("Deep Sleep mode Enter");
      deep_sleep_enter = false;
      nrf_gpio_pin_clear(SENSOR_PIN); // OFF Sensor
      nrf_gpio_pin_set(BLUE_LED_PIN); // OFF BLUE LED
      nrf_gpio_pin_set(GREEN_LED_PIN); // OFF Green LED
      nrf_gpio_pin_set(RED_LED_PIN); // OFF Red LED
      uint32_t err_code = bsp_indication_set(BSP_INDICATE_IDLE);
      APP_ERROR_CHECK(err_code);
      // Prepare wakeup buttons.
      err_code = bsp_btn_ble_sleep_mode_prepare();
      APP_ERROR_CHECK(err_code);
      // Go to system-off mode (this function will not return; wakeup will cause a reset).
      err_code = sd_power_system_off(); // ALl internal system clock functionality turn OFF
      APP_ERROR_CHECK(err_code);
    }

    But our sensor device not goes into deep sleep mode (System OFF) it will go into sleep mode (System ON) keep RTC running and wake up as per time configured and take measurement.

    When device is not using we put device into deep sleep and got current consumption = 1 - 5 uA which is acceptable for us.

    But when device working after taking sensor data it will go into sleep mode and will wake up as per configured time. In this mode the current consumption = 500 - 600 uA. Which is very high.

    We are trying to reduced this consumption got one issue for enabled and disabled UART peripheral. When i comment uart_init() function from my main. Then measured consumption with PPK got 31uA.

    Whats going wrong with UART module enabled or disable, Will you please suggest correct way for nRF52840 with SDK 15.0 version.

    Thanks...

Related