Butttonless DFU issue with CONFIG_NFCT_PINS_AS_GPIOS

[chandan]

I am using nrf52832 for button less DFU. DFU is working fine when  CONFIG_NFCT_PINS_AS_GPIOS is not added in applicaton. When added seems like code is getting reset at bootloader level. Is any connection with CONFIG_NFCT_PINS_AS_GPIOS ? Please suggest.

Thanks

[chandan]

Sorry I was offline last week.

As you suggested, I set a breakpoint at the if statement after nrf_dfu_settings_write_and_backup() call in nrf_dfu_settings_init() ,I found there is no error so on_error() in main is not getting called.

Thanks

[bjorn-spockeli]

Ok, so you reach the return NRF_SUCCESS statement at the end of nrf_dfu_settings_init()? If not then it could be the settings_forbidden_parts_copy_from_backup() function that tries to write data to a protected region. Can you check the value of the pointer passed to settings_forbidden_parts_copy_from_backup()?

Best regards

Bjørn

[chandan]

Also code can able to return NRF_SUCCESS statement at the end of nrf_dfu_settings_init()

[bjorn-spockeli]

Ok, can you just step through the code from that point until you see the device reset? What is the last function call/ line of code executed before the device resets?

The SD is not enabled at this point so stepping through the code should be fine. 

Best regards

Bjørn

[chandan]

In nrf_bootloader_app_start_final() after nrf_bootloader_flash_protect(), I am getting error code as 7 which is NRF_ERROR_INVALID_PARAM. Can this be reason for reset ?

[bjorn-spockeli]

Oh, so you're actually reaching the nrf_bootloader_app_start_final() function?

Any errors here will not cause a reset, just generate a log output. 

If app_start(vector_table_addr) is executed, then it means that the bootloader is branching to the application, i.e. the reset must be occuring in the application, not the bootloader. 

Can you try to debug the application by attaching to the running code in Segger Embedded Studio ( Target->Attach debugger) with the application project used to generate the application hex for the DFU image?

[chandan]

I tried but seems like code is not coming at main of application. I but breakpoint at starting but its not reaching till that point. Thanks

[bjorn-spockeli]

Ok, but you confirmed that app_start() is run til the end in the bootloader? You can also try to set a breakpoint in SystemInit() in system_nrf52.c. This function is called before main().

Best regards

Bjørn

[chandan]

I put breakpoints at SystemInit() at application code, and code is going inside SystemInit().  I feel application is resetting inside defined (CONFIG_NFCT_PINS_AS_GPIOS) at NVIC_SystemReset(). Is this correct ?

 

[chandan]

Below is the code inside, Not sure UICR_NFCPINS_PROTECT_Msk, UICR_NFCPINS_PROTECT_Pos ,

/* Configure NFCT pins as GPIOs if NFCT is not to be used in your code. If CONFIG_NFCT_PINS_AS_GPIOS is not defined,
two GPIOs (see Product Specification to see which ones) will be reserved for NFC and will not be available as
normal GPIOs. */
#if defined (CONFIG_NFCT_PINS_AS_GPIOS)
if ((NRF_UICR->NFCPINS & UICR_NFCPINS_PROTECT_Msk) == (UICR_NFCPINS_PROTECT_NFC << UICR_NFCPINS_PROTECT_Pos)){
NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen << NVMC_CONFIG_WEN_Pos;
while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
NRF_UICR->NFCPINS &= ~UICR_NFCPINS_PROTECT_Msk;
while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos;
while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
NVIC_SystemReset();
}
#endif

[chandan]

bjorn-spockeli please suggest.

[chandan]

Basiclly issue is as I am enabling CONFIG_NFCT_PINS_AS_GPIOS, NRF_UICR->NFCPINS should be disable, each reset it tries to do so but its coming always enable. I tried adding CONFIG_NFCT_PINS_AS_GPIOS in boot loader still its not working.

bjorn-spockeli Please suggest asap as this is bit urgent. 

Thanks