nrf9160 uart Pull-Up and power consumption

[MosheSmartAmr]

hi all,

i'm trying to disable uart for lower power consumption, i've disables it with:

NRF_UARTE1->TASKS_STOPTX = 1;
NRF_UARTE1->TASKS_STOPRX = 1;

but when i measure the voltage on the rx pin i see 1.8V  (this seems to consume current on the device on the other side of the uart interface - which is turned off )
i assume its in pulled up state, so i'm trying to change it's state to no-pull:

nrf_uarte_txrx_pins_disconnect(NRF_UARTE0);
gpio_pin_configure(uart_wifi, 18, GPIO_PUD_PULL_DOWN);
gpio_pin_configure(uart_wifi, 19, GPIO_PUD_PULL_DOWN);
gpio_pin_write(uart_wifi, 18,0);
gpio_pin_write(uart_wifi, 19,0);

 but it doesnt seem to have any effect.

how can i set this pin to 0, and back to 1 when I need it , on runtime?

Thanks

Moshe

[Vidar Berg]

Hi Moshe, 

Is the external IC power gated? It should drive the RX line to 'high' when it's inactive and powered. So that may explain why you see the current draw when you set the output to 0. 

Also, from your code snippets, it appears that you are stopping UART instance 1 while nrf_uarte_txrx_pins_disconnect() call takes instance 0 as an argument. Not sure if this is intended or not.

Best regards,

Vidar

[MosheSmartAmr]

Hi Vidar,

Thanks for your answer, 

1. I called `nrf_uarte_txrx_pins_disconnect()` on both UARTs (didnt copy it into the snippet).

2. I test this while the external IC is powered off  (it is gated ) . 

3. Just to be clear, even when I  disable UART from the SW, I still measure 1.8v on the TX pin . I guess it is still pulled up . 

Thanks and BR

[Vidar Berg]

Yes, it seems correct to me. So I don't see how the RX line could be 1.8v when the ext. device is powered off. But you mentioned that the external device seems to draw current. Did you determine that based on the total current consumption? 

[MosheSmartAmr]

Hi Vidar , 

>> Did you determine that based on the total current consumption? 

yes, I did.

How can I further debug this issue? 

[Vidar Berg]

Could you let me know the current consumption you see is? Here are some things you can try:

- Verify GPIO pin configuration RX and TX by reading out the configuration registers with your debugger. Also, the pin that controls the power to the external device if you use an output pin for it.

- If possible, get a baseline measurement by measuring the current consumption before enabling UARTE and power to external circuitries.  

- Check the enable registers for all UART instances. 

[MosheSmartAmr]

Hi,

1. current consumption is around 1ma.

2. Verified the GPIO's from the register and they look ok, the pins that contols the external device I measured the voltage and it looks corrct.

3. checked the ENABLE , they look ok . 

[Vidar Berg]

Hi,

To get a baseline measurement, is it possible to add a long sleep at the beginning of your code before you enable the UART instances, then try to measure the idle current? Or did you do that already?

[MosheSmartAmr]

what I did was to disable UART completely (from the code) and measure.

however, the issue is that i still measure 1.8v on the uart pin. 

somehow nothing I do seems to disable the uart pull-up.

[Håkon Alseth]

Hi Moshe,

 

Are you 100 % certain that its the nRF that is keeping this line high?

If you power off only the nrf91, does the voltage drop to gnd?

Is this measured on a nRF91-DK or a custom board? 

If it still is set high, can you please post any changed overlay/dts files?

 

PS: your stop/disable routines will not work as you intend them to, because when you issue TASKS_STOPRX=1, you have to wait for the EVENTS_RXTO to occur before you disable the UART instance (same goes for the TX, although its less of a change for that the occurring while you disable the peripheral), as stated here in the PS:

https://infocenter.nordicsemi.com/topic/ps_nrf9160/uarte.html?cp=2_0_0_5_18_6#concept_twi_low_power

 

Kind regards,

Håkon

[MosheSmartAmr]

Hi Hakon,

1. I'm pretty sure it is the NRF since the device on the other size is powered off.

2. if I disable UART completely, I see the line on LOW.

3. it is measured on a costum board.

4. attached. 

Thanks !!!

[Håkon Alseth]

Hi Moshe,

 

MosheSmartAmr said:

2. if I disable UART completely, I see the line on LOW.

 Never initialize it? ie: CONFIG_SERIAL=n? 

MosheSmartAmr said:

4. attached. 

 Looks like they weren't attached. Could you try .zip'ing it and then attach it? 

Did you try disabling per the recommendation in the datasheet, ie: wait for the events on RX and TX before completely disabling the peripheral to see if this has a difference on the behavior?

 

Kind regards,

Håkon

[MosheSmartAmr]

Hi,

Sorry for the delay ,

1.about CONFIG_SERIAL=n, this is exactly wht i did .

2. attaching again . 

3. just tried what you suggested (waiting for the event before disabling) , thath did not work too ...

overlay file:

/* SPDX-License-Identifier: Apache-2.0 */

&uart1 {
        current-speed = <115200>;
        compatible = "nordic,nrf-uarte";
        status = "okay";
        tx-pin = <19>;
        rx-pin = <18>;
};

dts file :

/*
 * Copyright (c) 2018 Nordic Semiconductor ASA
 *
 * SPDX-License-Identifier: Apache-2.0
 */

/ {
	model = "Nordic PCA10090 Dev Kit";
	compatible = "nordic,pca10090-dk", "nordic,nrf9160-sica",
		     "nordic,nrf9160";

	chosen {
		zephyr,console = &uart0;
		zephyr,shell-uart = &uart0;
		zephyr,uart-mcumgr = &uart0;
	};

	leds {
		compatible = "gpio-leds";
		led0: led_0 {
			gpios = <&gpio0 2 GPIO_INT_ACTIVE_HIGH>;
			label = "Green LED 0";
		};
		led1: led_1 {
			gpios = <&gpio0 3 GPIO_INT_ACTIVE_HIGH>;
			label = "Green LED 1";
		};
		led2: led_2 {
			gpios = <&gpio0 4 GPIO_INT_ACTIVE_HIGH>;
			label = "Green LED 2";
		};
		led3: led_3 {
			gpios = <&gpio0 5 GPIO_INT_ACTIVE_HIGH>;
			label = "Green LED 3";
		};
	};

	buttons {
		compatible = "gpio-keys";
		button0: button_0 {
			gpios = <&gpio0 8 GPIO_PUD_PULL_UP>;
			label = "Switch 1";
		};
		button1: button_1 {
			gpios = <&gpio0 9 GPIO_PUD_PULL_UP>;
			label = "Switch 2";
		};
		button2: button_2 {
			gpios = <&gpio0 6 GPIO_PUD_PULL_UP>;
			label = "Push button 1";
		};
		button3: button_3 {
			gpios = <&gpio0 7 GPIO_PUD_PULL_UP>;
			label = "Push button 2";
		};
	};

	/* These aliases are provided for compatibility with samples */
	aliases {
		led0 = &led0;
		led1 = &led1;
		led2 = &led2;
		led3 = &led3;
		sw0 = &button2;
		sw1 = &button3;
		sw2 = &button0;
		sw3 = &button1;
	};
};

&adc {
	status ="ok";
};

&gpiote {
	status = "ok";
};

&gpio0 {
	status = "ok";
};


&uart0 {
	status = "ok";
	current-speed = <115200>;
	tx-pin = <26>;
	rx-pin = <30>;
};

/*
&uart0 {
	status = "okay";
	current-speed = <115200>;
	tx-pin = <29>;
	rx-pin = <28>;
	rts-pin = <27>;
	cts-pin = <26>;
};
*/
&uart1 {
	status = "ok";
	current-speed = <115200>;
	tx-pin = <1>;
	rx-pin = <0>;
	rts-pin = <14>;
	cts-pin = <15>;
};

&i2c2 {
	status = "ok";
	sda-pin = <12>;
	scl-pin = <31>;
};

&pwm0 {
	status = "ok";
	ch0-pin = <2>;
};

&spi3 {
	status = "ok";
};

&timer0 {
	status = "ok";
};

&timer1 {
	status = "ok";
};

&timer2 {
	status = "ok";
};

&flash0 {
	/*
	 * For more information, see:
	 * http://docs.zephyrproject.org/latest/guides/dts/index.html#flash-partitions
	 */
	partitions {
		compatible = "fixed-partitions";
		#address-cells = <1>;
		#size-cells = <1>;

		boot_partition: partition@0 {
			label = "mcuboot";
			reg = <0x00000000 0x10000>;
		};
		slot0_partition: partition@10000 {
			label = "image-0";
		};
		slot0_ns_partition: partition@40000 {
			label = "image-0-nonsecure";
		};
		slot1_partition: partition@80000 {
			label = "image-1";
		};
		slot1_ns_partition: partition@b0000 {
			label = "image-1-nonsecure";
		};
		scratch_partition: partition@f0000 {
			label = "image-scratch";
			reg = <0x000f0000 0xa000>;
		};
		storage_partition: partition@fa000 {
			label = "storage";
			reg = <0x000fa000 0x00006000>;
		};
	};
};

/ {
	/* SRAM allocated and used by the BSD library */
	sram0_bsd: memory@20010000 {
		device_type = "memory";
		compatible = "mmio-sram";
	};

	/* SRAM allocated to the Non-Secure image */
	sram0_ns: memory@20020000 {
		device_type = "memory";
		compatible = "mmio-sram";
	};
};

/* Include partition configuration file */
#include "nrf9160_pca10090_partition_conf.dts"