nRF52840 Sensor Network with SPI Sensor

[Ekmekci]

Dear All,

I am working with nRF52840 product. According to my scenario i have 1central unit(master) and up to 19 peripheral unit(slave).

I downloaded SDK 15.3.0 ble_central and ble_pripheral examples. These examples are very very good. They are sending button and led situations.

In my project, i have SPI sensor at slaves. So, i should read Spi register value and send to the master. 

How i can add Spi reading in to the ble_peripheral example

Best regards,

[Simon]

If you want to merge SPI functions into the ble_peripheral example you'll have to do the following:

• Copy the example examples/ble_peripheral into the same folder with a new name, then open it and add the SPI related code
• The SPI functions you have added will have both header and source files associated with it and you have to make these files visible for the compiler
  • Add the paths to all the header files
  • Add the source (.c) files to Project Explorer
• Enable necessary peripherals and settings in the sdk_config.h file (look at the SPI examples to see what needs to be enabled)

Some cases about merging:

• https://devzone.nordicsemi.com/f/nordic-q-a/39199/cdc_acm-with-softdevice
• https://devzone.nordicsemi.com/f/nordic-q-a/39871/facing-an-error-while-initializing-nrf-crypto-library-and-ble-stack-together/155098#155098

If anything is unclear, or if you are struggling with any of the steps above please tell me and I will explain more thoroughly.

Best regards,

Simon

[Ekmekci]

Dear Simon,

First of all, thank for your quick help.

Let me explain my point to you.

There is one master, and one slave. 

In slave side i connected acceloremeter via SPI to nRF52840.

My point is just, get one register value from my acceloremeter and send to the master via BLE

I just want to learn which example code i need to use. 

Please show way to do it to me

[Nguyen Hoan Hoang]

This blog post shows you an easy way to achieve it. 

http://embeddedsoftdev.blogspot.com/2018/01/

[Ekmekci]

Actually,

Multilik central and peripheral example is OK for me.

But, all these examples just are sending button state and led state (1bit) 

I need to send data (variable, counter, etc) and when sended data in receiver side i should compare this data ( if (rec_data == "Hello World!")) 

[Simon]

If you want to transfer strings over a BLE connection, from a peripheral to a central, you have to set some parameters which you provide to sd_ble_gatts_hvx():

char my_array[] = "HEY";
uint16_t length = sizeof(my_array);
.
.
.

params.p_len  = &length;
params.p_data = my_array;  
sd_ble_gatts_hvx(p_our_service->conn_handle, &hvx_params);

On the central side, you will receive the data as ASCII number. In the case above, the central will receive 0x48 45 59. If you cast these hex values to a char's after receiving, you'll be able to read the string 

Best regards,

Simon

[Ekmekci]

I really dont understand, 

Either Nordic examples are very complex, or i dont understand.

I am trying to send my data over ble almost with 2months but i still cant do it.

I am just trying to sen "Counter = xxx" string to center unit. 

It seems it is impossible...

[Simon]

Ekmekci said:

I am trying to send my data over ble almost with 2months but i still cant do it.

I am just trying to sen "Counter = xxx" string to center unit. 

Could you be more specific on where you are stuck? Did you see my answer below? Did that make sense? If not, what specifically did you not understand?

Could you provide some code? Then it will be easier for me to understand what you are trying to do.

Best regards,

Simon