Simple SPI

[verulia]

Hello,

I am using nrf9160 and want to test the just simple SPI function. The code that I found from github(https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/spi c) is old and gives me too many errors. Are there any simple SPI code that I can try in my nrf9160 board in order to test whether I can send a simple data via SPI. I also found spi_flash_at45 however I don't have any device from at45 family to test it so another simple example would be so helpful for me. 

Thank you

[Håkon Alseth]

Hi,

 

Generic test code for nRF5340 can be found here:

https://devzone.nordicsemi.com/f/nordic-q-a/67065/how-to-configure-and-setup-an-spi-device-to-nrf5340/276687

 

I added some small modifications to the above sample, as SPI0 is shared with UART0/TWIM0 etc on nRF9160:

4520.simple_spi_test_nrf9160.zip

 

Kind regards,

Håkon

[verulia]

Hi,

Thank you for the fast reply. I just ran the code however I am always receiving 0 in the RX_recv. Shouldn't the value in RX_recv be similar with TX_sent since this code is just tries to send a value and receive it back as far as I understood? I didn't make any change in the code yet.

Q2:

I want to send data from nrf9160 to an external device, in order to just make a simple test before implementing a flash driver, I want to test the pins and spi, for that I am using scana to check the signals coming from spi ports. My question here is that how can I send my data to scana rather than making a loopback. For instance first I have to ad a chip select for scana, adding ss=<13> to the overlay file can be the first step right? What should I change other than this?

Thank you

[verulia]

Hi,

I tested the logic analyzer for testing other gpio pins and it working however I still can't see any signal from spi code. GND is connected and I can't see clock,miso and mosi. I reverse the pins for mosi and clk however I am always getting 1(high) from <10> port. I also tried to decrease the sampling rate but still I am always getting hi from <10> port even though the GND is not connected. I should be able to directly observe the clk signal from logic analyzer right without changing anything in the code? 

Thank you

[Håkon Alseth]

The sample doesn't send all the time (once per second), are you sure you're triggering on the correct channel, with the correct edge triggering?

[verulia]

I didn't do any triggering, I just connected one port to the ground and other port to clk output. As trial I triggered the output channel of clk port both risinf and falling but result didn't change. 

[verulia]

Hello,

I think I misunderstood the switching part because I just try to switch the pins of mosi and clk in the overlay file by just writing mosi<10> clk<11> however this doesn't work. How can I switch them what is the right way?

Thank you

[Håkon Alseth]

You can use another gpio by setting the .overlay file.

For instance:

&spi3 {
	compatible = "nordic,nrf-spim";
	status = "okay";
	sck-pin = <x>;
	mosi-pin = <y>;
	miso-pin = <z>;
};

 

Where x, y, z are a valid and unused gpio. If it doesn't switch the gpios, try deleting your build folder and re-importing the project.

 

Kind regards,

Håkon

[verulia]

Hi Hakan,

The pins are changed no problem in that part rigth now but still I can't see the rigth signal in the logic analyzer. I adjusted edge triggering with rising edge( also tried with falling and all other triggering options) I see that clk signal seems always high. Not 0-1-0-1 its always one.I played with sampling frequency but it also didn't change the result. I tested the logic analyzer with different chip and I saw 1-0-1-0 clk signal so logic analyzer is working fine. I didn't change the code that you sent me and it is doing loopback so no problem in spi functionality. Then what should I do in this case? I just want to see the clk signal and mosi in this case I thought that just attaching the logic analyzer to those output pins was sufficient to see the outputs am I missing something in this point?

Thank you

[verulia]

Hi, I couldn't get an answer for my last reply do you have any idea of what can I also try?

Thank for the help so much

[Håkon Alseth]

Hi,

 

On the UART terminal (serial terminal), are you getting the expected output when connecting MISO to MOSI using a patch wire?

ie: 

TX sent: X

RX recv: X

 

BR,

Håkon

[verulia]

Hi,

Yes when I connect miso to mosi with a wire I receive the same value. I also changed the gpio pins for clk and miso it also works fine when I change them I can still see the outputs on lte link monitor. The only problem is I cant even see the clk ouput 1-0-1-0 on logic analyzer, I also cant see mosi. The clk pin always gives 1 in logic analyzer but it should be 0-1-0-1. I changed the sampling rate, frequenct however still result is same. I didn't understand what I am missing. Should I have to make additional changes in the code or should I need to do some adjustments in the logic analyzer. But in logic analyzer when I just send 1-0-1-0 from gpio pins(different from spi pins) I was be able to see the output clearly without doing any modification

Thank you

[Håkon Alseth]

Hi,

 

verulia said:

Yes when I connect miso to mosi with a wire I receive the same value. I also changed the gpio pins for clk and miso it also works fine when I change them I can still see the outputs on lte link monitor. The only problem is I cant even see the clk ouput 1-0-1-0 on logic analyzer, I also cant see mosi.

If you are not able to view the data on your logic analyzer when looking at MISO, but the serial output shows that it sends for instance 10 and receives 10 when you connect MISO to MOSI, then the pin itself does toggle.

It is then a problem with your logic analyzer PC setup.

 

Kind regards,

Håkon