• State Not Answered
  • Replies 17 replies
  • Subscribers 68 subscribers
  • Views 6984 views
  • Users 0 members are here
Attachments (0)
Nordic Case Info
  • Case ID: 266292
Options
This post is older than 2 years and might not be relevant anymore
More Info: Consider searching for newer posts

Programming custom NRF52832 board using SWD interface

DineshB

Hello NRF,

I have a custom board with NRF52832, and exposed the SWDIO, SWDCLK, GND, VDD, RESET pins for programming the board through the NRF52-DK board.

I started with a sample peripheral_uart, connected the NRF52-DK board to my PC, and managed to BUILD and RUN the sample application.

I verified that the app is working, by connecting to the UART service advertised by this app (on NRF52-DK) through another device that has NRF-TOOLBOX and used the UART service to query the NRF UART (NRF52-DK board) and managed to read write and verified the same over the console.

Now, I want to program my custom board, instead of the NRF52-DK board. Based on some suggestions on this site, I connected the

NRF52-DK        CUSTOM_BOARD

SWDIO             SWDIO

SWDCLK          SWDCLK

GND-DET         GND

VTG                 VDD/3V3

I then powered my board and then tried the BUILD and RUN option on the SEGGER.

It seems like my custom board is not getting programmed.

I would like to know : 

1. Do I have to first program a bootloader on to my custom board. If so, please advise a boot loader that I can download from your site (if possible) and the steps to program the same on to my custom board.

2. How to program the compiled/build binary/hex files on to my custom card? Just BUILD and RUN would download the binary on to the connected custom board, instead of the NRF52-DK board? (because my custom board is connected through the SWD port and GND detected?) If BUILD and RUN wouldn't work, where can I find the compiled binary or hex file where I can program the same on to the custom board , perhaps by using command line nrfjprog tool???

3. I believe the peripheral_uart has it's pin definitions, for the RX, TX, LEDs etc. Since my custom board pin assignments might be different from that of the NRF52-DK, where can I find these definitions, so I can go map the pins?

All I need is to demonstrate this peripheral_uart app on my custom nrf52832 board, where I will connect a serial port on to its RX/TX to a putty terminal (on my pc) and then able to rx/tx data back and forth with the other connected device (NRF toolbox -> UART).

I appreciate your help in this regard.

regards,

Dinesh.

Parents
  • 0

    Hi again Dinesh

    You're using nRFConnect SDK (NCS), correct? And thus this example project? If you only have the one external crystal that explains why it doesn't start advertising. In order to run most of our examples, you also need to use a LF clock (32.768 kHz), and our example projects are configured to use the optional external (XTAL) 32.768kHz crystal. You can configure the example to use the internal RC oscillator instead though, which should make the application run as intended.

    1. NCS does not use the SoftDevices, so it seems like you're mixing up the nRF5 SDK and the nRFConnect SDK.

    2. I believe it should be sufficient to configure the project to use the RC oscillator instead of the XTAL. Please see the documentation here for details. The calibration should be enabled by default when the RC oscillator is enabled it seems.

    Best regards,

    Simon

  • 0 in reply to Simonr

    Hello Simon,

    I connected the NRF52-DK to the Sparkfun dev kit, as per your instructions. (My custom design is based on the Sparkfun dev kit design).  You can check their schematics here,

    sparkfun-nrf52832-breakout.sch

    Based on their schematics (which is what my current designs are based on), both the 32MHz and 32KHz crystals are connected.

    I am using nRF Connect v3.6.1 and nRF Connect SDK v1.4.2 and peripheral_uart project.

    Even with this Sparkfun development board, I am unable to get the peripheral_uart project up and running, whereas I have verified that the Sparkfun board is working through a different (Arduino) toolchain/IDE.

    Please advise, what could be the problem here. I see that both the crystals are connected. When I BUILD & RUN from the SES, there is no error thrown, and looks like the flashing goes smoothly. 

    I believe, if I can get this dev kit to work with the SES + peripheral_uart project, then I can simply get my custom hardware to work with the SES + perhipheral_uart as well.

    Looking forward to hearing back from you soon.

    regards,

    Dinesh.

Reply
  • 0 in reply to Simonr

    Hello Simon,

    I connected the NRF52-DK to the Sparkfun dev kit, as per your instructions. (My custom design is based on the Sparkfun dev kit design).  You can check their schematics here,

    sparkfun-nrf52832-breakout.sch

    Based on their schematics (which is what my current designs are based on), both the 32MHz and 32KHz crystals are connected.

    I am using nRF Connect v3.6.1 and nRF Connect SDK v1.4.2 and peripheral_uart project.

    Even with this Sparkfun development board, I am unable to get the peripheral_uart project up and running, whereas I have verified that the Sparkfun board is working through a different (Arduino) toolchain/IDE.

    Please advise, what could be the problem here. I see that both the crystals are connected. When I BUILD & RUN from the SES, there is no error thrown, and looks like the flashing goes smoothly. 

    I believe, if I can get this dev kit to work with the SES + peripheral_uart project, then I can simply get my custom hardware to work with the SES + perhipheral_uart as well.

    Looking forward to hearing back from you soon.

    regards,

    Dinesh.

Children
No Data
Related