Interaction between timer and saadc

[CktDesigner]

I'm writing software for nRF52832 using nRF5 SDK v17.0.2

I'm using a timer to create a buzz/tone using timer 3.    This works as expected.

I'm also using the SAADC to measure the voltage on input pin AIN3.   Since I only need this value occasionally, I only call the ADC conversion when needed.   Here is the code:

//
// ADC for voltage measurement
//
void saadc_callback(nrfx_saadc_evt_t const * p_event) {
  NRF_LOG_INFO("ADC event");
}

void
saadc_init(void) {
  ret_code_t err_code;

  //err_code = nrf_drv_saadc_init(NULL, saadc_callback);
  //APP_ERROR_CHECK(err_code);
  nrfx_saadc_config_t adcConfig;
  adcConfig.low_power_mode     = true;
  adcConfig.resolution         = NRF_SAADC_RESOLUTION_12BIT;
  adcConfig.oversample         = NRFX_SAADC_CONFIG_OVERSAMPLE;
  adcConfig.interrupt_priority = APP_IRQ_PRIORITY_LOW;
  err_code = nrfx_saadc_init(&adcConfig, saadc_callback);
  APP_ERROR_CHECK(err_code);

  // Configure channel 0
  nrf_saadc_channel_config_t channelConfig0;
  channelConfig0.reference     = NRF_SAADC_REFERENCE_INTERNAL;
  channelConfig0.gain          = NRF_SAADC_GAIN1_6;
  channelConfig0.acq_time      = NRF_SAADC_ACQTIME_10US;
  channelConfig0.mode          = NRF_SAADC_MODE_SINGLE_ENDED;
  channelConfig0.burst         = NRF_SAADC_BURST_DISABLED;
  channelConfig0.pin_p         = VBATT_PIN;   // AIN3 = P0.05
  channelConfig0.pin_n         = NRF_SAADC_INPUT_DISABLED;
  channelConfig0.resistor_p    = NRF_SAADC_RESISTOR_DISABLED;
  channelConfig0.resistor_n    = NRF_SAADC_RESISTOR_DISABLED;
  // Configure Channel 0
  err_code = nrfx_saadc_channel_init(0, &channelConfig0);
  APP_ERROR_CHECK(err_code);
}


nrf_saadc_value_t
getBattVoltage(void) {
  ret_code_t err_code;
  nrf_saadc_value_t sample;

  // Sample channel 0
  err_code =nrfx_saadc_sample_convert(0, &sample);
  APP_ERROR_CHECK(err_code);

  return sample;
}

Since I'm not continuously sampling the ADC, no timer was set up for it.   Is the ADC set up and being used properly?

When the "saadc_init" function executes, the tone generation no longer works.    If I comment out the call to "saadc_init" (obviously the ADC can't be used), the tone generator works.

I didn't see anything in the documentation that mentions any interaction/dependency between the saadc and timer 3.

Did I miss something?

Thanks!

[Kenneth]

When the "saadc_init" function executes, the tone generation no longer works.

Are you sure the code is not asserting? If you build with Debug (not Release) you may get more information about the assert in app_error_fault_handler().

[CktDesigner]

Yes, I'm building in the "Debug" configuration.   No asserts are thrown. 

I don't see anything in the saadc_init() function that should interact with the timer...