Rerouting AT interface for power measurement using external supply

[Frikkie Badenhorst]

Hi there,

We received your devkits on Friday, 25th of June and started evaluation of the modules this morning (Magnus Pederson and Brian Kim @ Nordic arranged the devkits for us). We are able to successfully connect to the network and do current measurements. Since we are on a tight schedule, I was hoping you could assist with the following simple issue:

We will be using a supply voltage of around 3.3 - 3.6V, and would thus want to evaluate the power consumption at that supply. For this, we add an external supply to P21 and bridge SB20. We then add a current meter (Nordic PPK2) to P22. We do however only want to evaluate the power profile of the nRF9160 chip, and not the interface MCU. We thus put SW6 in the "right" position.

When this is the case, the UART interfaces are not available on the USB connector. Also when having the USB cable connected, the supply voltage is 5V, so we do not want to have the USB cable connected at all. Thus to communicate via the serial interface with the nRF9160, we will need to reroute the UART pins to the external connectors. We can then use a serial-to-usb adapter to communicate using a simple terminal program (TeraTerm).

Could you please advise as to what would be the quickest way to do this? Which UART port is the AT interface (UART0/1/2)? I guess we will also have to disable HW flow control for this test as our Serial to USB adapter has only a TX, RX and GND wire.

We are reaching out simply to speed up the evaluation process.

Thanks in advance!

Kind regards,

Frikkie Badenhorst

[Stian Røed Hafskjold]

Hi, please follow my guide here on how to measure current on the nRF9160 DK: https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/hardware-design/posts/getting-started-with-current-measurements-on-the-nrf9160

I think the easiest way is using the SMU method, then you can supply P22 directly with the voltage you need and measure current at the same time. You leave the USB cable plugged in for UART/debugging, and the USB will then power everything on the DK except the nRF91 VDD itself. So there will be now leakage current from the nRF91 to the rest of the DK, nor will the nRF91 be powered by the USB.

No modifications to the DK are needed, and SW6 can be left in the default position.

[Frikkie Badenhorst]

Hi Stian, 

Thank you for your response. Yes the SMU looks as if it will work.

Also, what application can we flash onto the the SiP in order to do manual current testing? 

We currently have the asset tracker application flashed onto the module, however we are having issues installing the nRD Connect SDK and getting it running with SEGGER Embedded Studio (I have created a seperate ticked for that), so thus for now cannot create our own custom apps.

Should simply erasing the firmware on the app processor be fine?

[Stian Røed Hafskjold]

Hi, button 1 on the DK should wake the device up again

[Frikkie Badenhorst]

Thanks Stian.

I have accidentally closed the ticket, but I believe you are still preparing the update LTE Serial Modem app which will allow the expected idle current.

[Stian Røed Hafskjold]

Yes, here is a new hex file with the expected idle current: 8547.merged.hex

[Frikkie Badenhorst]

Excellent, thanks Stian! Your help is greatly appreciated

[Frikkie Badenhorst]

Hi Stian, it looks as if we are still seeing a base current of 30-40uA with 8547.merged.hex in the idle state. 

We have tried both AT#XSLEEP=0 and AT#XSLEEP=1

[Stian Røed Hafskjold]

This is probably due to the SIM card being active. The SIM is active if the DRX interval (the spikes you see every 640ms (?)) is less than 1 minute.

You can check this by measuring the voltage on the SIM current measurement header. If it's 1.8V the SIM is in clock stop mode and is consuming between 20-100 uA depending on the SIM card. It should be 0V when the SIM is shut down.

Try to put the modem in PSM mode, which will turn off the SIM, to get the lowest current consumption. The following AT command requests PSM mode with a 5 minute ("10001010") TAU wakeup interval, and the active time set to 0 ("00000000"). The active time specifies how long the modem should stay in DRX mode after going to PSM, after each wakeup.

AT+CPSMS=1,"","","10001010","00000000"

You should also enable unsolicited notifications at level 5, which will return the PSM settings which is actually given by the network. It does not always match the requested ones.

AT+CEREG=5
AT+CEREG?

The response should look something like this:

+CEREG: 1,"7BD5","0106C601",7,0,2,"00000000","10001010"

If the fields in red above are set to 11100000, PSM is not activated and might not be supported by the network

https://infocenter.nordicsemi.com/topic/ref_at_commands/REF/at_commands/nw_service/cereg_set.html?cp=2_1_7_7_0

https://infocenter.nordicsemi.com/topic/ref_at_commands/REF/at_commands/nw_service/cpsms_set.html?cp=2_1_7_2_0

[Frikkie Badenhorst]

Thanks Stian, we have a fully configurable test network and base station (Amarisoft Callbox Mini), so we force the network to basically accept any timer request by the UEs.

When using the 5 minute TAU wakeup and 0 minute active time as you mentioned, I can see the device going into a 3uA state. 

However, as a test I am setting the following:

Active timer: 30minutes 

TAU: 7 hours

eDRX cycle: 655sec (+- 11 minutes)

PTW: 5.12 sec

From this, 

Stian Røed Hafskjold said:

This is probably due to the SIM card being active. The SIM is active if the DRX interval (the spikes you see every 640ms (?)) is less than 1 minute

I would think that the SIM should be deactived since the DRX cycle is larger than 1minute, but we still see the 39uA current after the PTW is complete:

Is this expected behaviour? Then I guess that the SIM card is always active during the active time, regardless of the DRX cycle?

[Stian Røed Hafskjold]

Sorry, forgot to mention, you need to set the power saving profile. Use the AT%XDATAPRFL command and set the level to 0.

The power saving level has an effect on the shutdown of the UICC during Extended Discontinuous Reception (eDRX) cycles. On power level 0, the modem deactivates the UICC if the eDRX period is longer than 60 seconds and UICC deactivation is allowed through EF-AD under USIM ADF. The modem activates the UICC and performs the necessary checks before setting up any signaling or data connections with the network. Otherwise, the UICC is not activated because of modem functionality.

On power levels 1–4, the modem deactivates the UICC if the eDRX cycles are longer than 10 minutes. The UICC is activated before any signaling or data connections are set up with the network and when waking up from eDRX. This means that the UICC is deactivated and activated at every eDRX cycle.

[Stian Røed Hafskjold]

The text marked in red in the previous answer is kind of important as well. This field has to be set in the SIM, which it's usually not by default. If you have a regular test-SIM for your callbox, you probably have the ADM key and can change this field.

[Frikkie Badenhorst]

Ok for now we are still not able to get it in a lower power between DRX cycles. Will have to look into the setting of the field on the SIM. When testing a modem from a different manufacturer however, we are not seeing this, which makes me wonder if it is indeed the SIM.

Nonetheless for now we can work with this value we are seeing as a test.

Thanks for all your assistance, Stian.