Internal driver Error related to the BME280 on NRF5340

[Rihab]

Hello,
i hope you're doing well 

i'm using NRF5340 kit and trying to display ( H,T,P) values with the BME280 sensor 
but i'm getting this error 

i'm recently having an issue with the display of the values of the BME280
well it's displaying this error when the sensor is connected to the Kit

and it's displaying this error with the other address when it's not connected

Knowing that : 

0x0BAD0001 means "Internal Error" in the I2C driver.

0x0BAE0001 means "Address not acknowledged" in the I2C driver.
and doubting that the issue may be with how the sensor is wired to the board, or setup in some way, causing an error in the driver.


for me i did the wiring like this 

P1.02 to SDI
P1.03 to SCK
GND to SDO
GND to GND
Vin 3-5v to VIN

is there a pre-config to do or some settings to fix before running the sensor ?

can you please help me with the wiring 
if you already tried the sensor, how did it go with you please ?
can you help me please 
i would be very grateful

thank you in advance

[Rihab]

i managed to get out of the driver internal error that i had
but for now i'm getting this output .it's looking for the device but every time it says that there's no device found
i put you the output below

*** Booting Zephyr OS build v2.6.0-rc1-ncs1  ***
Flash regionsDomainPermissions
00 03 0x00000 0x10000 Securerwxl
04 63 0x10000 0x100000 Non-Securerwxl

Non-secure callable region 0 placed in flash region 2 with size 32.

SRAM regionDomainPermissions
00 03 0x00000 0x08000 Securerwxl
04 63 0x08000 0x80000 Non-Securerwxl

PeripheralDomainStatus
00 NRF_P0               Non-SecureOK
01 NRF_CLOCK            Non-SecureOK
02 NRF_RTC0             Non-SecureOK
03 NRF_RTC1             Non-SecureOK
04 NRF_NFCT             Non-SecureOK
05 NRF_NVMC             Non-SecureOK
06 NRF_UARTE1           Non-SecureOK
07 NRF_UARTE2           SecureSKIP
08 NRF_TWIM2            Non-SecureOK
09 NRF_SPIM3            Non-SecureOK
10 NRF_TIMER0           Non-SecureOK
11 NRF_TIMER1           Non-SecureOK
12 NRF_TIMER2           Non-SecureOK
13 NRF_SAADC            Non-SecureOK
14 NRF_PWM0             Non-SecureOK
15 NRF_PWM1             Non-SecureOK
16 NRF_PWM2             Non-SecureOK
17 NRF_PWM3             Non-SecureOK
18 NRF_IPC              Non-SecureOK
19 NRF_VMC              Non-SecureOK
20 NRF_FPU              Non-SecureOK
21 NRF_EGU1             Non-SecureOK
22 NRF_EGU2             Non-SecureOK
23 NRF_DPPIC            Non-SecureOK
24 NRF_REGULATORS       Non-SecureOK
25 NRF_DCNF             SecureSKIP
26 NRF_CTRLAP           SecureSKIP
27 NRF_SPIM4            Non-SecureOK
28 NRF_WDT0             Non-SecureOK
29 NRF_WDT1             Non-SecureOK
30 NRF_COMP             Non-SecureOK
31 NRF_LPCOMP           Non-SecureOK
32 NRF_PDM0             Non-SecureOK
33 NRF_I2S0             Non-SecureOK
34 NRF_QSPI             Non-SecureOK
35 NRF_NFCT             Non-SecureOK
36 NRF_MUTEX            Non-SecureOK
37 NRF_QDEC0            Non-SecureOK
38 NRF_QDEC1            Non-SecureOK
39 NRF_USBD             Non-SecureOK
40 NRF_USBREGULATOR     Non-SecureOK
41 NRF_P1               Non-SecureOK
42 NRF_OSCILLATORS      Non-SecureOK
43 NRF_RESET            Non-SecureOK
44 NRF_GPIOTE1          Non-SecureOK

SPM: NS image at 0x10000
SPM: NS MSP at 0x20008d00
SPM: NS reset vector at 0x12295
SPM: prepare to jump to Non-Secure image.
*** Booting Zephyr OS build v2.6.0-rc1-ncs1  ***

Error: no device found.

do you can help me with this please
do you know how to make the device visible please
i really need your help

[Rihab]

update to the ticket and the display of the BME280 on NRF5340
make sure the voltage is what your sensor needs in this case it needs to be connected to VDDnrf pin in order to get the right so just follow the right steps and then make sure your pins are wired correctly 
like below : 
P1.02 to SDI
P1.03 to SCK
GND to SDO
GND to GND
VDDnRF to VIN