5340DK can't be recognized as Jlink

[helen]

Hi Noridc,

I have a nRF5340DK, it has worked well for some months, and now it grows wrong.

When connect to the PC via USB, the device is not recongized as Jlink or any other device, and the programmer(nrf connect for PC) shows 'no devices available'.

The LED5 turn on to nromal brightness in about 1 second, not like good DK wihch will blink some times and keep on.

I have searched the devzone, and only found some topic about 52840DK, I have tried to power on the 5340DK with pressed the RESET button, nothing happened.

I think maybe the firmware of Jlink lose but I don't know how to fix it.

What can I do with this DK?

[Priyanka]

Hi,

Could you tell me what OS are you trying this on? (Windows, Linux, Mac OS)

Regards,

PK

[helen]

Hi PK

Windows10 64bit.

[helen]

Hi PK,

Yes, I have tried 3 USB cables, which are fine with other DKs.

[Priyanka]

Hi Helen,

Then you probably have accidentally deleted the firmware like you had suspected. You could follow this Thread and try troubleshooting.

First, we need to confirm whether this is the issue, so please try the steps 1,2,3,5 and 6 from the thread and then we can move to step 4.

Then, reinstalling the firmware in the nRF53 DK's is not quite as easy as in the nRF52 DK as mentioned in the thread.

Hope this helps and kindly let me know how it goes. We can go onto the step 4 after you cross out all others.

Kind Regards,

PK

[helen]

Hi PK,
I have try the steps 1,2,3,5,6, and there isn't any exception.

So I tried step 4, power cycling the DK with pressing the RESET button, there is not a Stroage Device named 'bootloader' appear.

What can I do now?

[Priyanka]

Hi Helen,

You cannot do the step 4 as easily as mentioned in the Thread, which is what I mentioned earlier. This is because these downloadable options are currently available only for nRF52 DK. I can guide you through the steps for the nRF53, now that we have ruled out all the options from steps 1,2,3,5 and 6.

1. Could you confirm whether the solder bridge SB40 has been cut at any point on the DK?

2. Also, could you kindly download the latest nrfjprog version (10.15.0)

3. Please tell me which version of DK is it that you are using and also the J-Link version.

[helen]

Hi PK,

Priyanka said:

1. Could you confirm whether the solder bridge SB40 has been cut at any point on the DK?

I have checked the SB40, it havn't been cut.

Priyanka said:

2. Also, could you kindly download the latest nrfjprog version (10.15.0)

I am downloading the nRF Command Line Tools 10.15.0, about 10 minutes later it will be OK.

Priyanka said:

3. Please tell me which version of DK is it that you are using and also the J-Link version.

On the Jlink IC, there is 'PCA10095  0.11.0  2021.10   960127268', maybe this is the Jlink version.

But I can't find the version of DK, where can I find it?

[Priyanka]

Hi,

You can try searching for Jlink in your search and it can be seen

Mine is version V7.54d

[Jason]

Hi,

I encounter the same issue with my nRF5340 DK. How can I recover it?

[Priyanka]

You could try installing the Troubleshooting methods mentioned earlier in this Thread. Also, you can try nrfjprog --recover followed by nrfjprog --eraseall in your command prompt.

See if this helps.