Programming a custom PCB with host MCU and Murata MBN52832 through NRF52DK P20 pins. ( "No idcode detected" Error)

[FurkanSenol]

Hello. I have a custom board which contains S32K148 MCU and Murata MBN52832 BLE Module and several other modules like GPS, LTE etc. Board is powered via external 12 V adapter but through voltage regulators modules are powered with 3.3V.

I am using SEGGER Embedded Studio as IDE.

I am trying to program MBN52832 module through its SWD pins using NRF52DK's P20 pins and pin connections goes like this:

P20.SWDIO          ---->  Custom Board SWDIO

P20.SWCLK         ---->  Custom Board SWCLK

P20.VTG               ---->  P20.VDD (To activate external flashing)

P20.GND Detect   ---->  Custom Board GND ( Custom board and NRF52DK have common grounds on a breadboard )

Now the problem is when I try to flash my code into custom PCB I get the following error.

"Failed to connect to target. No idcode detected. Please check connection and Target Interface Type."

I have read almost every post about external programming on here DevZone but the suggested solutions on other posts did not work for my problem.

I double-checked the board for soldering problems etc.

Application works fine on NRF52DK's internal NRF52832 SoC so I do not think it's a software based problem.

I'd appreciate any suggestion regarding this matter. Thanks in advance.

Best regards,

Furkan

 

[Vidar Berg]

Hi Furkan,

No idcode detected indicates that the debugger is unable to communicate with the target IC. This usually means that there is a connection problem, or that the IO voltages don't match. Can you measure the voltage on the SWDIO pad on your custom board when it is powered but not connected to the debugger? The SWDIO line has an internal pull-up hand should therefore match the VDD voltage on your board. 

Best regards,

Vidar

[FurkanSenol]

Hi Vidar,

Thanks for your reply. I measured the voltage on SWDIO and got the result of 3.31 Volts

Best regards,

Furkan

[Vidar Berg]

Hi Furkan,

Reset and SWO are optional, and SWO is rarely used anyway. The UART lines should not be a problem either. 

Do you have only one board to test on?

Best regards,

Vidar

[FurkanSenol]

Hi Vidar,

Unfortunately yes I have only one board to test on, at least for now. 

I watched the voltage change on SWDCLK and SWDIO pins (pin 25 and 26) of DK's internal SoC with an oscilloscope while flashing the chip just to see what I'm expecting from the module on my custom board. I can see clear square signals on the pins and SWDIO starts from HIGH state and SWDCLK starts from LOW state, but when I measured the SWDCLK pin on the MBN52832 module I got 3.3 Volts. I read that nRF52832 has internal pull-up resistor on SWDIO and internal pull-down resistor on SWDCLK pins. Could this be a problem? If so I'll ask my hardware team colleagues to check the module's connection again.

Best regards,

Furkan

[Vidar Berg]

Hi Furkan,

Yes, you are right, there CLK line should be low due to the internal pull up. Is there any chance it may be connected to the wrong pin on the module?

Best regards,

Vidar

[FurkanSenol]

Hi Vidar,

After detecting the SWDCLK pin's problem we tried to diagnose why it is pulled-up to HIGH. It seems there were several internal issues on the board. Now I am working on different board and we are able to flash the MBN52832 module. Thanks for your help and interest!

Best regards,

Furkan

[Vidar Berg]

Hi Furkan,

Thanks for reporting back to us. This confirms that it was some kind of connection issue at least.

Best regards,

Vidar