i am not able make it as a controller

[Achyuth]

 Hy 

i am using a nrf5349 Dk board ,i am able to build and flash the board.

but when i am using this by building and flashing the board with hci_uart .in the linux system i am not able to make it as a controller .can any one help me with the steps to be followed for the board to make it as a controller .

Thanks 

[Sigurd Hellesvik]

Hi,

Try to use the HCI USB sample instead.

Then use the "nRF USB" connector to connect after flashing the DK.

Regards,
Sigurd Hellesvik

[Achyuth]

Hy sigurd ,

thank you for the replay 

i tried hci_usb also 

steps i followed 

1. building the hci_usb in the git bash 

2.flashing the hci_usb

3. then i connected the board to the linux laptop 

here i use the commands

a. treminal 1 . btmon

b .terminal 2 . sudo btattach -B /dev/ttyACM0 -S 115200 -P h4 

c. terminal 3 .sudo btmgnt -i 1

    [hci1]# auto-power
Found controller with index 1

in my btmon screen i am able to see that status as success 

can you conform this process is correct?

[Sigurd Hellesvik]

Hi,

For pasting long logs, please use the Insert->Code functionality. It will make the case more tidy.

I build the hci_usb project again for the nRF Connect SDK v2.1.0. Here is the hex: 3480.merged.hex

Which version of Linux are you using?

Regards,
Sigurd Hellesvik

[Achyuth]

Hi sigurd 

i have tried flashing the merged hex file which you sent .
i am using the 22.04 linux version .

But when i tried to do btattach .its shows this in the btmon

[Sigurd Hellesvik]

Hi,

Do you get the same error for other ttyACM channels as well?

Regards,
Sigurd Hellesvik

[Achyuth]

yes , i got the same error for all the channels 

[Achyuth]

hi check this file for what i am getting , and i tried with the three channels

$ sudo dmesg
[ 4974.576258] usb 2-1: new full-speed USB device number 3 using xhci_hcd
[ 4974.723952] usb 2-1: New USB device found, idVendor=1366, idProduct=1055, bcdDevice= 1.00
[ 4974.723965] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4974.723998] usb 2-1: Product: J-Link
[ 4974.724002] usb 2-1: Manufacturer: SEGGER
[ 4974.724006] usb 2-1: SerialNumber: 000960124132
[ 4974.733106] cdc_acm 2-1:1.0: ttyACM0: USB ACM device
[ 4974.734862] cdc_acm 2-1:1.2: ttyACM1: USB ACM device
[ 4974.735884] cdc_acm 2-1:1.4: ttyACM2: USB ACM device
[ 4974.736969] usb-storage 2-1:1.7: USB Mass Storage device detected
[ 4974.737378] scsi host3: usb-storage 2-1:1.7
[ 4975.756681] scsi 3:0:0:0: Direct-Access     SEGGER   MSD Volume       1.00 PQ: 0 ANSI: 4
[ 4975.758772] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 4975.759775] sd 3:0:0:0: [sdb] 21829 512-byte logical blocks: (11.2 MB/10.7 MiB)
[ 4975.760512] sd 3:0:0:0: [sdb] Write Protect is off
[ 4975.760519] sd 3:0:0:0: [sdb] Mode Sense: 0b 00 00 08
[ 4975.760980] sd 3:0:0:0: [sdb] No Caching mode page found
[ 4975.761014] sd 3:0:0:0: [sdb] Assuming drive cache: write through
[ 4975.770900]  sdb:
[ 4975.772511] sd 3:0:0:0: [sdb] Attached SCSI removable disk

[Sigurd Hellesvik]

Hi,

Sample: v2.1.0/zephyr/bluetooth/hci_usb
nRF Connect SDK: v2.1.0
Board: nrf5340dk_nrf5340_cpuapp

8154.merged.hex

merged_CPUNET.hex

Flash:

nrfjprog--recover--coprocessor CP_NETWORK
nrfjprog--recover

nrfjprog -f NRF53 --coprocessor CP_NETWORK --program build/hci_rpmsg/zephyr/merged_CPUNET.hex --chiperase
nrfjprog -f NRF53 --coprocessor CP_NETWORK --verify build/hci_rpmsg/zephyr/merged_CPUNET.hex
nrfjprog -f NRF53 --verify build/zephyr/merged.hex
nrfjprog -f NRF53 --program build/zephyr/merged.hex --chiperase

nrfjprog --reset

Regards,
Sigurd Hellesvik